期刊文献+

聚合物溶液在多孔介质中流动规律实验研究 被引量:2

Flow Regular Pattern Experiment of Polymer Solution in Porous Medium
下载PDF
导出
摘要 由于孔隙介质的复杂性和聚合物溶液的黏弹性,导致聚合物溶液在多孔介质中流动与在流变仪中的流动相比更加复杂,同时聚合物溶液在多孔介质中的流动规律直接关系到驱油方案的制定。因此本研究设计并开展了聚合物溶液(部分水解聚丙烯酰胺)在岩心中流动参数测定实验,给出了岩心渗透率、聚合物溶液质量浓度、聚合物相对分子质量、聚合物溶液注入速度对阻力系数、岩心中流动黏度的影响规律。结果表明,聚合物溶液存在一个临界质量浓度,当溶液质量浓度低于临界质量浓度时,阻力系数与表观黏度基本相等;当溶液质量浓度高于临界质量浓度时,阻力系数远小于溶液表观黏度,且随着溶液质量浓度增加,两者之间差值增大。聚合物溶液在岩心中流动黏度远小于溶液在流变仪中表观黏度,且随着溶液质量浓度增加,溶液在岩心中流动黏度的增加幅度远小于溶液表观黏度的增加幅度。 Due to the complexi ty of porous media and viscoelast ici ty of polymer solution, the flow behavior of polymer solution in porous media is more complex than that in the rheometer and the flow regular pattern of polymer solution in porous media directly affects the formulation of polymer flooding projects. In this paper, experiment of polymer solution (partially hydrolyzed polyacrylamide.) in porous media was designed, and the regular pattern of influence on resistance factor and flow viscosity in porous media caused by core permeability,polymer concentration,polymer molecular weight and polymer injection rate was given. The followings are the results: there exists a critical polymer concentration , whenpolymer concentration is lower than critical concentration,resistance factor is basical ly equal to apparenpolymer concentration is higher than critical concentration, resistance factor is far less than apparent viscosity and the difference value is increased with the increase of polymer concentration. F'low viscosity of polymer solution in porous apparent viscosity in the rheometer and when polymer concentration increases, the increase extent of flow viscosity is far lessthan the increase of apparent viscosity.
出处 《石油化工高等学校学报》 CAS 2016年第6期23-26,共4页 Journal of Petrochemical Universities
基金 国家自然科学基金项目(51474070) 黑龙江省自然科学基金项目(D2015008)
关键词 聚合物溶液 多孔介质 阻力系数 表观黏度 流动黏度 Polymer solution Porousmedia Resistance factor Apparent viscosity Flow viscosity
  • 相关文献

参考文献4

二级参考文献18

  • 1黄家贤.高分子化学基础[M].北京:化学工业出版社,1986.
  • 2Noik Ch, Delaplace Ph. Physico- chemical characteristics of polyacrylamide solutions after mechanical degradation through a porous medium[J].SPE 28954 MS,1995.
  • 3国家技术监督局.GB12005.1-1989聚丙烯酰胺特性粘数测定方法[S].北京:中国标准出版社,1989.
  • 4Seright R S. The effects of mechanical degradation and viscoelastic behavior on injectivity of polyacrylamide solutions[J]. SPE 9297--PA,1983.
  • 5[4]利特马恩 W.聚合物驱油[M].杨普华,杨育深,译.北京:石油工业出版社,1991.
  • 6[5]庞宗威.聚合物分子量与岩心渗透率匹配关系的研究[M].北京:石油工业出版,1990.
  • 7Audibert A, Arjillier J F. Thermal stability of sulfonated polymers[R].SPE 28953,1995:81-91.
  • 8梁兵,代华,黄荣华.AM/DMAM/AMPS共聚物的合成及结构分析[J].油田化学,1997,14(3):248-251. 被引量:26
  • 9王滨玉,张军,贾忠盛.大庆油田聚合物驱油工业化推广应用研究[J].石油勘探与开发,1997,24(6):51-55. 被引量:10
  • 10孔柏岭,唐金星,谢峰.聚合物在多孔介质中水动力学滞留研究[J].石油勘探与开发,1998,25(2):68-70. 被引量:10

共引文献32

同被引文献30

引证文献2

二级引证文献6

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部