期刊文献+

转动副临界角分析及其在四连杆机构中的应用 被引量:3

Critical angle of revolute pin joint and its application in a four-bar mechanism
下载PDF
导出
摘要 滑动配合条件下,转动副(R副)通过接触面间的相对滑动提供一个转动自由度。由于接触面间的摩擦和间隙共同作用,R副会在一个小的摆角范围内发生自锁,这一摆角将在机构平衡时带来连杆长度误差和连杆偏角误差。本文指出了R副中临界角的存在,讨论了使得R副实现自锁的临界角范围,在考虑接触变形和不考虑接触变形2种条件下对临界角进行了计算,并以一平面四连杆机构作为应用算例,综合对比了铰链间隙、接触变形和摩擦因素对所在连杆机构输出精度的影响。算例结果表明,在一般的精度计算中铰链间隙及连杆弹性变形起主要影响作用,铰链本身的接触变形量可忽略。 Revolute pin joint (revolute pair) possesses one degree of freedom, i.e. rotation movement, through relative sliding between contact pairs. Existence of friction and clearance in revolute joints has crucial effects on the overall precision of mechanism. Using the concept of critical angle, the marginal value in which revolute joints could keep in balance state is discussed in this study. Firstly, frictional angle and self-lock caused by friction and clearance in revolute pin joints are investigated, which contribute to not only length er- ror but also angle error in mechanism with such joints. Then, critical angles are calculated with and without contact deformation respectively. Moreover, a four-bar mechanism with one revolute joint studied above is cho- sen as a case study to evaluate the impact of clearance of joint, contact deformation and friction on the overall precision. Analytical results indicate that the clearance in revolute joint and elastic deformation of mechanism play the most important roles in the system, and the contact deformation of joint could be neglected in the overall precision analysis.
出处 《北京航空航天大学学报》 EI CAS CSCD 北大核心 2016年第12期2738-2744,共7页 Journal of Beijing University of Aeronautics and Astronautics
基金 国家自然科学基金(51305013)~~
关键词 转动副(R副) 临界角 摩擦角 平面四连杆机构 精度分析 revolute pin joint (revolute pair) critical angle frictional angle four-bar mechanism pre-cision analysis
  • 相关文献

参考文献3

二级参考文献121

  • 1王伟,贠超.机器人机构精度综合的正交试验法[J].机械工程学报,2009,45(11):18-24. 被引量:18
  • 2赵杰,王卫忠,蔡鹤皋.可重构机器人封闭形式的运动学逆解计算[J].机械工程学报,2006,42(8):210-214. 被引量:17
  • 3廖启征 梁崇高 张启先.空间7R机构位移分析的新研究.机械工程学报,1986,22(3):1-9.
  • 4Duffy J. Analysis of mechanisms and robot manipulators [ M ]. London:Edwart Arnold Ltd,1980.
  • 5Etzel K R, McCarthy J M. A metric for spatial displacement using biquaternions on SO ( 4 ) [ C ]//Proceedings of IEEE International Conference on Robotics and Automation. Piscataway, NJ:IEEE ,1996:3185 - 3190.
  • 6Geng Q J, Varshney A, Menon J P,et al. Double quaternions for motion interpolation [ C ]//Proceedings of the ASME DETC' 98. Atlanta:ASME,1998:13 - 16.
  • 7McCarthy J M. Mechanisms synthesis theory and the design of robots[ C ]//Proceedings of IEEE International Conference on Robotics and Automation. San Francisco, CA : IEEE ,2000:24 - 28.
  • 8Clifford W K. A preliminary sketch of biquaternions[ G]//Tucker R. Mathematical Papers. London : London Mathematical Society, 1582:655.
  • 9Machine axis identification standard EIA-267-B Axis and motion nomenclature for numerically controlled machines.2001.
  • 10ISO 841:2001 Industrial automation systems and integration-numerical control of machines-coordinate system and motion nomenclature.ISO,Geneva.

共引文献59

同被引文献9

引证文献3

二级引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部