期刊文献+

The Effect of Heating Direction on Flow Boiling Heat Transfer of R134a in Microchannels 被引量:2

The Effect of Heating Direction on Flow Boiling Heat Transfer of R134a in Microchannels
原文传递
导出
摘要 This paper presents effects of heating directions on heat transfer performance of R134 a flow boiling in micro-channel heat sink. The heat sink has 30 parallel rectangular channels with cross-sectional dimensions of 500mm width 500mm depth and 30 mm length. The experimental operation condition ranges of the heat flux and the mass flux were 13.48 to 82.25 W/cm^2 and 373.3 to 1244.4 kg/m^2 s respectively. The vapor quality ranged from 0.07 to 0.93. The heat transfer coefficients of top heating and bottom heating both were up to 25 k W/m^2 K. Two dominate transfer mechanisms of nucleate boiling and convection boiling were observed according to boiling curves. The experimental results indicated that the heat transfer coefficient of bottom heating was 13.9% higher than top heating in low heat flux, while in high heat flux, the heat transfer coefficient of bottom heating was 9.9%.higher than the top heating, because bubbles were harder to divorce the heating wall. And a modified correlation was provided to predict heat transfer of top heating. This paper presents effects of heating directions on heat transfer performance of R134 a flow boiling in micro-channel heat sink. The heat sink has 30 parallel rectangular channels with cross-sectional dimensions of 500mm width 500mm depth and 30 mm length. The experimental operation condition ranges of the heat flux and the mass flux were 13.48 to 82.25 W/cm^2 and 373.3 to 1244.4 kg/m^2 s respectively. The vapor quality ranged from 0.07 to 0.93. The heat transfer coefficients of top heating and bottom heating both were up to 25 k W/m^2 K. Two dominate transfer mechanisms of nucleate boiling and convection boiling were observed according to boiling curves. The experimental results indicated that the heat transfer coefficient of bottom heating was 13.9% higher than top heating in low heat flux, while in high heat flux, the heat transfer coefficient of bottom heating was 9.9%.higher than the top heating, because bubbles were harder to divorce the heating wall. And a modified correlation was provided to predict heat transfer of top heating.
出处 《Journal of Thermal Science》 SCIE EI CAS CSCD 2017年第2期166-174,共9页 热科学学报(英文版)
基金 supported by the National Natural Science Foundation of China(No.51376019)
关键词 流动沸腾传热 内加热 微通道 R134A 换热性能 通道宽度 截面尺寸 质量流量 top heating, bottom heating, flow boiling, micro-channels, R134a, correlation
  • 相关文献

参考文献1

二级参考文献33

  • 1Mertens, R. G., Chow, L., Sundaram, K. B., Cregger, R. B., Rini, D. E, Turek, L., Saarloos, B. A., (2007), Spray Cooling of IGBT Devices, Journal of Electronic Packag- ing, Vol. 129, No. 3, pp. 316-323.
  • 2Bhunia, A., Chandrasekaran, S., Chen, C. L., (2007), Performance Improvement of a Power Conversion Mod- ule by Liquid Micro-jet Impingement Cooling, Journal of Components and Packaging Technologies, Vol. 30, No. 2, pp. 309-316.
  • 3Pautsch, A. G, Gowda, A., Stevanovic, L., Beanpre, R., (2009), Double-Sided Microchannel Cooling of a Power Electronics Module Using Power Overlay, Proceedings of ASME 2009 InterPACK Conference collocated with the ASME 2009 Summer Heat Transfer Conference and the ASME 2009 3rd International Conference on Energy Sustainability, San Francisco, California, USA, July 19-23, pp.427-436.
  • 4Mudawar, I., Bharathan, D., Kelly, K., Narumanchi, S., (2009), Two-phase Spray Cooling of Hybrid Vehicle Electronics, Joumal of Components and Packaging Technologies, Vol. 32, No. 2, pp. 501-512.
  • 5Rahimo, M., Kopta, A., Eicher, S., Schlapbach, U., Lind- er, S., (2004), Switching-Self-Clamping-Mode" SSCM', a Breakthrough in SOA Performance for High Voltage IGBTs and Diodes, Proceedings of the 16th International Symposium on Power Semiconductor Devices and ICs (ISPSD 10), Kitakyushu, Japan, May 24-27, pp. 437-440.
  • 6Hitachi, T., Gohara, H. and Nagaune, F., (2012), Direct Liquid Cooling IGBT Module for Automotive Applica- tions, Power Semiconductor Contributing in Energy and Environment Region, Vol. 58, No. 2, pp. 55.
  • 7Campbell, J. B., Tolbert, L. M., Ayers, C. W., Ozpineci, B., Lowe, K. T. , (2007), Two-phase Cooling Method Using the R134a Refrigerant to Cool Power Electronic Devices, Journal of Industry Applications, Vol. 4, No. 33, pp. 648-656.
  • 8Kim, D. W., Rahim, E., Bar-Cohen, A., Han, B., (2010), Direct Submount Cooling of High-power LEDs, Journal of Components and Packaging Technologies, Vol. 33, No. 4, pp. 698-712.
  • 9Bar-Cohen, A., Rahim, E., (2009), Modeling and Predic- tion of Two-phase Microgap Channel Heat Transfer Cha- racteristics, Journal of Heat Transfer Engineering, Vol. 30, No. 8, pp. 601-625.
  • 10do Nascimento, F. J., Le~o, H. L. S. L., Ribatski, G., (2013), An Experimental Study on Flow Boiling Heat Transfer of R134a in a Microchannel-based Heat Sink, Journal of Experimental Thermal and Fluid Science, Vol. 45, pp. 117-127.

共引文献2

同被引文献2

引证文献2

二级引证文献5

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部