期刊文献+

汽车内饰把手气辅注射成型模具设计 被引量:5

Design of Gas-assisted Injection Molds for Car Interior Door Handles
下载PDF
导出
摘要 采用满射型逆吹式气辅成型技术,对汽车内饰把手进行了模具设计。在溢料槽结构设计中,通过增设切断阀和使用热流道针阀式喷嘴,改善了溢料效果,克服了以往逆吹式气辅成型的缺点。浇口采用牛角式潜伏浇口,并通过合理选择顶出位置,保证了产品外观无浇口与顶出痕迹。该模具成型出的产品表面无缩痕,获得了良好的外观品质,较同类产品质量减轻了20%。 An injection mould for a car interior handle was designed by using an inverse blowing gasassisted molding technology in a full injection mode.When designing the groove structure for melt overflow,cut-off valve and hot runner nozzle were introduced into the mould so as to improve the efficiency of melt overflow and also to overcome the defects appearing in the inverse blowing gasassisted molding.With the use of a horn-shape latent gate and the reasonable setting of ejection position,the aspects without any gate and ejector marks were guaranteed for the injection-molded parts.This mould has been used for the production of parts,and the products exhibit a good appearance as well as a lightweight feature with a reduction in weight by 20 % compared with the similar products.
出处 《中国塑料》 CSCD 北大核心 2017年第4期102-105,共4页 China Plastics
关键词 逆吹式 气辅成型 溢料槽 切断阀 缩痕 inverse blowing type gas-assisted injection molding resin-overflow groove cut-off valve shrinkage mark
  • 相关文献

参考文献5

二级参考文献37

  • 1许一德.工艺参数在气辅注塑成型中的活用[J].模具技术,2004(5):43-46. 被引量:2
  • 2王小新,刁军臣,张明磊,邵振,于昕世,单义旭.CAE技术在电视机前壳气辅模具开发中的应用[J].模具工业,2005,31(1):34-37. 被引量:13
  • 3申长雨,王利霞,李倩,陈静波,刘春太.注塑成型充填过程的可压缩流动分析[J].化工学报,2006,57(7):1537-1542. 被引量:3
  • 4李健辉,黄志高,周华民,李德群,蔡考群.塑料注射成型滞流现象分析及其解决方法[J].塑料工业,2007,35(6):26-28. 被引量:4
  • 5李倩,王小峰,申长雨.气辅成型过程气体穿透行为[J].化工学报,2007,58(7):1847-1850. 被引量:3
  • 6CHIANG H H, HIEBER C A, WANG K K. A unified simulation of the filling and posffilllng stages in injection molding. Part I: Formulation[J]. Polymer Engineering and Science,2004,31 (2) :116-124.
  • 7HUA Min, LI De-qun. Filling simulation and penetration modeling for gas assisted injection molding [ J ]. Applied Mathematical Modelling, 2003,27 (11) :851-852.
  • 8CHEN S C, CHENG N T. A simple model for evaluatlon of contribution factors to skin melt formation in gas assisted injection molding[ J]. International Communications in Heat and Mass Transfer, 1996,23 (2) :216.
  • 9LI C T, ISAYEV A I. Primary and Secondary Gas Penetration During Gas-assisted Injection Molding Part I: Formulation and Modeling[ J]. Polymer Engineering And Science,2004,44(5) :985.
  • 10CHIANG H H, HIEBER C A, WANG K K. A unified simulation of the filling and postfilling stages in injection molding Part Ⅱ: Experimental verification [ J]. Polyluer Engineering and Science,2004,31 (2) :125-139.

共引文献10

同被引文献57

引证文献5

二级引证文献11

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部