期刊文献+

某后桥半轴密封垫的选用与半轴螺栓力矩性能的影响分析

The Selecting of Seal Spacer and Torque Analysis of the Shaft Bolt for a Rear Drive Axle
下载PDF
导出
摘要 后桥总成是整车的重要组成部分,通常全浮式轮端密封主要依靠油封密封,为了辅助密封,防止半轴与轮毂结合面渗油,则在两者之前增加一层密封垫作为一种辅助密封方式,如何选择密封垫需要进行验证分析,最终选定合适的密封垫。既能起到辅助密封的作用,又不会因半轴密封垫的材质等性能因素影响原半轴螺栓的拧紧力矩的性能,并为后期半轴密封垫设计提供一定的参考依据。 Rear drive axle is one of the most important parts of the vehicles , we normally apply oil seal to the full-floating wheel end to avoid leaking oil. And also , we add a paper spacer to the joint of sh-,Lft and wheel hub to enhance sealing effect. How to select a proper paper spacer is also proved by the analysis of the experiment. Se- lecting a proper paper spacer will be very much helpful to avoid leaking oil and the material of paper spacer will not affect the torque of the shaft bolt. It also makes a reference to designers of this field.
作者 马寅锟 刘松
出处 《装备制造技术》 2017年第4期59-61,共3页 Equipment Manufacturing Technology
关键词 后桥总成 半轴密封垫 拧紧力矩 wheel hub assembly paper spacer the shaft bolt torque
  • 相关文献

参考文献1

二级参考文献20

  • 1John H. Biekford. Gaskets and Gasketed Joints[M],New York: 1998.
  • 2Bazergui, A. Payne, J. Progress in Gasket Testing-Milestone Results[J]. Press. Vess. Tech. 1984,106(1):93-103.
  • 3J. R. Payne, R. T. Mueller, A. Bazergui. A Gasket Qualification Test Scheme for Petrochemical Plants: Part 1-Test Methods and Application Results [J].ASME/PVP. 1989,158 : 53-68.
  • 4A. Bazergui. Short Term Creep and Relaxation Behavior of Gaskets[J]. WRC Bulletin, 1984,294:922.
  • 5M. Derenne, L. Marchand et al. Polytetrafluoroethylene(PTFE) Gasket Qualification. WRC Bulletin 422[J]. 1999,(11),1-47.
  • 6L. Marchand, M. Derenne. Long Term Performance of Elastomeric Sheet Gasket Materials Subjected to Temperature Exposure[J]. International Conference on Pressure Vessel Technology, ASME 1996,1 : 107-123.
  • 7A. Bazergui, R. Payne et al. Summary Report on Elevated Temperature Tests for Asbestos-free Gasket Materials[J]. MTI Publication No. 35.
  • 8L. Marchand, M. Derenne, A. Bazergui. Weight Loss Correlation for Sheet Gasket Materials [J].Pressure Vessel Technology, 1992,114(2) : 1 -7.
  • 9J. R. Payne, R. T. Mueller, A. Bazergui. A. Gasket Qualification Test Scheme for Petrochemical Plants: Part Ⅱ-Quality Criteria and Evaluation Schemes[J]. ASME/PVP. 1989,158:69-79.
  • 10M. Derenne, J. R. Payne et al. Development of Test Procedures for Fire Resistance Qualification of Gaskets[J]. WRC Bullrtin, 1992,377 : 1-19.

共引文献3

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部