期刊文献+

基于人工视觉的运动成绩校对标准器的嵌入式设计

Embedded design of sport performance calibrator based on artificial vision
下载PDF
导出
摘要 针对传统校对标准器一直存在嵌入式设计不准确的问题,提出基于人工视觉的运动成绩校对标准器的嵌入式设计。硬件采用ARM处理器代替传统的大型换算处理器、嵌入式待换机以及集成电源电路;软件上利用人工视觉进行反汇编视觉模型设计,通过设计的反汇编视觉模型能够进行运动成绩的分项标准测定,优化寄存代码计算,对设计的视觉模型标准化进行了标准限定。为了验证设计的基于人工视觉的嵌入式运动成绩校对标准器的有效性,模拟应用环境进行仿真试验,通过实验的数据分析,有效地证明了设计的基于人工视觉的嵌入式运动成绩校对标准器的有效性。 As the inaccurate problem existing in the embedded design of the traditional proofreading standard,the embedded design of sport performance calibrator based on artificial vision is proposed. The hardware ARM processor is used to replace the traditional large conversion processor,embedded changing machine and integrated circuit. The software uses artificial vision for the disassembly visual model design. The determination of subitem standard for sport performance can be performed through the design of disassembly visual model to optimize storage of code calculation. A standardization design criteria is made for the visual model. In order to verify the effectiveness of the embedded sport performance calibrator based on visual design,a simulation test of application environment was carried out. The analysis the experiment data demonstrated the effectiveness of the embedded sport performance calibrator based on artificial vision effectively.
作者 曾红武 彭丽
出处 《现代电子技术》 北大核心 2018年第2期60-62,67,共4页 Modern Electronics Technique
基金 重庆市科技计划项目专项(cstc2015shms-ztzx10011)~~
关键词 人工视觉 运动成绩校对 嵌入式标准器 集成电路源 ARM处理器 分项标准 artificial vision sports performance proofreading embedded standard integrated circuit ARM processor subitem standard
  • 相关文献

参考文献2

二级参考文献21

  • 1王晓嘉,高隽,王磊.激光三角法综述[J].仪器仪表学报,2004,25(z3):601-604. 被引量:167
  • 2刘健庄,栗文青.灰度图象的二维Otsu自动阈值分割法[J].自动化学报,1993,19(1):101-105. 被引量:357
  • 3王少清,庄葆华,张文伟.基于朗伯定律重建光学三角法测位移原理公式[J].光学学报,1996,16(12):1802-1808. 被引量:15
  • 4L Thivillon, I M Bertrand. B Lagel, et aL. Potential of direct metal deposition teclinology for manufacturing thick fiinclionallygraded coatings and parts for reactors components[J]. Journal of Nuclear Materials, 2009,385(2): 236-241.
  • 5K I Schwendner, R Banerjee, P C Collins, et al.. Direct laser deposition of alloys from elemental powder blends[J]. Scripta Materialia,2001,45(10): 1123-1129.
  • 6C L Atwood, M L Griffith, M E Schlienger, et al. Laser engineered net shaping (LENSTM): A tool for direct fabrication of metal parts[C]. Processing of the Laser Materials Processing Conference Section A-ICALEO/1998, 1998, 16-19: E-l.
  • 7T Gareth, Mark Pridham. Improvements to laser forming through process control refinements[J]. Optics & Laser Technology, 1998,30(2): 141-146.
  • 8G J Bi, A Gasser, K Wissenbach, et al.. Investigation on the direct laser metallic powder deposition process via temperature measurement[J]. Appl Surf, 2006, 253(3): 1411-1416.
  • 9Zhu Gangxian, Li Dichen,Zhang Anfeng, et al.. The influence of laser and powder defocusing characteristics on the surface qualityin laser direct metal deposition[J]. Optics & Laser Technology, 2012, 44(2): 349-356.
  • 10H Dongming, R Kovacevic. Sensing, modeling and control for laser-based additive manufacturing[J]. International Journal of MachineTools and Manufacture, 2003, 43(1): 51-60.

共引文献23

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部