期刊文献+

金属粉末注射成型催化脱脂料POM/PP/Ti的流变行为及脱脂工艺 被引量:4

Rheological Behaviors and Degreasing Process of Polyformaldehyde/Polypropylene/Titanium Catalytic Degreasing Materials Used for Metal Powder Injection Molding
下载PDF
导出
摘要 利用聚甲醛(POM)/聚丙烯(PP)复合黏结剂与钛合金粉末制备出催化脱脂型专用料。结果表明:提高粉末含量会使专用料粘度增大,且专用料对温度的敏感性较低,能在较宽范围内注射成型;加入EVA和硬脂酸锂可进一步降低体系的表观粘度。当氮气通入速率为100 cm^3/min,硝酸通入速率为0.010~0.050 cm^3/min时,注射坯脱脂效率高。POM被脱脂去除后,样品依然保持原有的形状与结构。 Polyformaldehyde(POM)/polypropylene (PP) composite binder and titanium alloy powder were used to prepare catalytic degreasing dedicated materials. The results show that increasing the content of titanium alloy powder can increase the viscosity of dedicated materials. The sensitivity of dedicated materials to the temperature is low, which can be injected in a wide temperature range. In addition, adding EVA and lithium stearate can furtherly reduce the apparent viscosity of the system. The injection billet degreasing efficiency is high when the nitrogen inlet rate is 100 cm3/min and the nitric acid inlet rate is 0.010-0.050 cm3/min. The sample still maintains the original shape and structure after the catalytic degreasing of POM.
作者 章诚 刘春林
出处 《热加工工艺》 CSCD 北大核心 2017年第24期45-49,54,共6页 Hot Working Technology
基金 江苏省产学研前瞻性联合研究项目(BY2016029-06)
关键词 聚甲醛 聚丙烯 钛合金粉末 流变行为 催化脱脂 polyformaldehyde polypropylene titanium alloy powder rheological behaviors catalytic degreasing
  • 相关文献

参考文献4

二级参考文献41

  • 1杜学丽,秦明礼,冯培忠,曲选辉.AlN粉末注射成形喂料的流变性能研究[J].材料工程,2007,35(4):35-38. 被引量:12
  • 2王霖林,杨现锋,张振庭,谢志鹏.陶瓷注射成型热脱脂与水基脱脂的机理研究[J].稀有金属材料与工程,2007,36(A01):330-333. 被引量:13
  • 3Fleischer J, Dieckmann A M. Automation of the powder injection molding process [ J ]. Microsystem Technologies,2006,12 ( 7 ) :702 - 706.
  • 4Antusch S, Norajitra P, Piotter V, et al. Powder injection molding-an innovative manufacturing method for He - cooled DEMO divertor components[ J ]. Fusion Engineering and Design,2011,86(9) :1575 - 1578.
  • 5Wang Q, Yin H,Qu X,et al. Effects of mold dimensions on rheological of feedstock in micro powder injection molding [ J ]. Powder Technology ,2009,193 ( 1 ) : 15 - 19.
  • 6Piotter V, Mueller T, Plewa K, et al. Manufacturing of complex - shaped ceramic components by micropowder injection molding [ J ]. The International Journal of Advanced Manufacturing Technology, 2010, 46(1 -4) :131 - 134.
  • 7Rub A,Piotter V, Plewa K, et al. Studies on size accuracy of mierogear wheels produced by powder injection molding of zirconia feedstocks[ J]. The International Journal of Advanced Manufacturing Technology,2012, 58(9 - 12) :1051 - 1059.
  • 8Piotter V, Muener T, Plewa K, et al. Manufacturing of complex - shaped ceramic components by micropowder injection molding [ J ]. The International Journal of Advanced Manufacturing Technology, 2010, 46(1 -4) :131 - 134.
  • 9Abolhasani H, Muhamad N. A new starch - based binder for metal injection molding [ J ]. Journal of Materials Processing Technology, 2010,210(6) :961 -968.
  • 10Enneti R K,Shivashankar T S,Park S J,et al. Master debinding curves for solvent extraction of binders in powder injection molding [ J ]. Powder Technology,2012,228 : 14 - 17.

共引文献15

同被引文献48

引证文献4

二级引证文献6

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部