期刊文献+

SUS430不锈钢制品侧壁开裂原因分析及改进 被引量:1

Analysis and Improvement of Side Wall Cracking of SUS430 Stainless Steel Products
下载PDF
导出
摘要 对SUS430铁素体不锈钢冲压制品侧壁开裂样品进行研究分析,开裂钢卷45°方向的r值为0.6,正常钢卷45°方向r值为0.75,开裂钢卷45°方向r值较低。通过SEM分析开裂处,主要是富含Mg、Al、O的镁铝尖晶石类夹杂导致SUS430原料在冲压过程中抗45°方向变薄的能力降低,因此造成侧壁出现开裂。现场通过采取提升第一炉钢水纯净度控制措施,连铸钢包钢水全氧含量达到了40mg/L以下,钢水纯净度得到了较大的提升,后续跟踪改进后的SU430钢卷,冲压开裂现象已经得到了明显的控制。 The sidewall cracking samples of SUS430 ferritic stainless steel stamping products were investigated and analyzed.It is found that the R value in the 45°direction of the cracked steel coil is 0.6,the R value of the normal steel coil is 0.75,and the R value in the 45°direction of the cracking steel coil is lower than that of the SUS430 steel.It is found that the magnesia spinel inclusions rich in Mg,Al and O lead to the reduction of the ability of SUS430 material to resist 45°direction thinning during the stamping process,resulting in cracking on the side wall.The scene through enhancing the purity of molten steel in continuous casting ladle control measures,total oxygen content reached 40 ppm,the purity of molten steel can be greatly improved,SU430 steel follow-up improved volume,the phenomenon of cracking by stamping has been obviously controlled.
作者 刘有东 刘天增 程云霞 喻大钢 LIU You-dong;LIU Tian-zeng;CHENG Yun-xia;YU Da-gang(The Stainless Steel Branch of Hongxing Stock Company, Jiayuguan 735100, China)
出处 《甘肃冶金》 2018年第3期22-25,共4页 Gansu Metallurgy
关键词 SUS430 成形性能 开裂 夹杂物 r SUS430 fonnability craze inclusions r
  • 相关文献

参考文献6

二级参考文献32

  • 1杜伟,江来珠,孙全社,余海峰,刘振宇.凝固组织对超低碳铁素体不锈钢皱褶和深冲性的影响[J].宝钢技术,2010,3(2):25-29. 被引量:6
  • 2王明林,成国光,杨新娥,赵沛,仇圣桃,干勇.含钛低碳钢凝固过程中氧化钛的析出和长大[J].钢铁研究学报,2004,16(5):47-50. 被引量:5
  • 3王绪,杨弟,毛为民,章守华.超深冲IF钢退火过程中织构变化的ODF分析[J].钢铁研究学报,1995,7(1):60-65. 被引量:11
  • 4顾善德.不锈钢深拉深件口部开裂初探[J].锻压技术,1990,15(5):32-35. 被引量:3
  • 5姜周华,李阳.洁净不锈钢冶炼技术[c]//2006年全国炼钢、连铸生产技术会议文集.北京:中国金属学会,2006:59.
  • 6Herrera Trejo M, Castro M R, Mendez J N, et al. Evolution of Inclusion Nature During the EAF-LF-CC Process [J]. Scan- dinavian Journal of Metallurgy, 1998, 27(6) : 233.
  • 7路世英,张廷凯,康喜范.不锈钢[M].北京:原子能出版社,1995.
  • 8Yazawa Y, Muraki M, Kato Y. Effect of chromium content on relationship between r-value and I llll recrystallization texture in ferritic steel[ J ]. ISIJ International, 2003,43 ( 10 ) : 1647 - 1651.
  • 9Sztwiertnia K, Pospiech J. Orientation topography andridging phenomenon in ferritic stainless steel sheets [ J]. Arch Metall, 1999,44(2) :157 165.
  • 10Ray R K, Jonas J J, Hook R E. Cold rolling and annealing textures in low carbon and extra low carbon steels [ J ]. International Materials Reviews, 1994,39 (4) : 129 - 172.

共引文献80

同被引文献7

引证文献1

二级引证文献3

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部