期刊文献+

硅铝粉体陶瓷膜分离过程分析及膜清洗方法探讨 被引量:3

Silicon Aluminum Powder Liquid Ceramic Membrane Separation Process and Membrane Cleaning Method Discussed
下载PDF
导出
摘要 分析了陶瓷膜分离低浓度硅铝粉体母液的过程,并探讨了膜清洗方法。多批次小试实验结果表明,物料浓缩10倍时,膜通量在300L/m2h左右且保持稳定,浓缩液中硅铝粉体浓度相应提高10倍左右。膜清洗首先考虑使用高温碱溶液或常温酸溶液,但单独的高温碱或酸并不能恢复膜通量,需两者组合清洗才能使膜通量恢复,酸碱的使用顺序不影响洗膜效果。由于常温下物料本身呈强碱性,因此常温碱对膜清洗没有效果。大批量实验结果表明,浓缩40倍后,膜通量虽有下降,但仍保持较好过滤性能。膜清洗后膜通量恢复,浓缩液中硅铝粉体含量符合要求,保证了实际工程的可行性。浓缩液循环实验表明,高浓度条件下长时间过滤,陶瓷膜仍然保持良好过滤性能。膜清洗后仍可恢复膜通量,保证了陶瓷膜使用寿命。 Analyzed the ceramic membrane separation process of low concentration silicon aluminum powder mother liquid, and discussed the membrane cleaning method. Multiple batches experimental results showed, membrane flux keep about 300 L/m2 h when material was 10 times concentrated. And the concentration of silicon silicon aluminum powder corresponding increased about 10 times. Membrane cleaning using high temperature alkali or normal temperature acid solution, but the high temperature alkali or normal temperature acid alone did not recover the membrane flux. The combination of high temperature alkali and normal temperature acid cleaning could restore the membrane flux, and the acid and alkali using order didn't affect the washing effect of membrane. Because materials are strong alkaline, normal temperature alkali on membrane cleaning hadn't effect. Large scale experimental results showed that the concentration after 40 times, membrane flux was decreased, but still maintained well filtering performance. Membrane flux was recovery after cleaning and silicon aluminum powder content in the concentrate met requirements,which ensured the feasibility of practical engineering. Concentrate cycle experiments showed that ceramic membrane maintain well filtering performance after high conce ntration for a long time filtration. Membrane flux could be recovery after cleaning, which ensured the service life of ceramic membrane.
作者 杨晓明 彭文博 吴正雷 熊福军 赵宏亮 Yang Xiaoming;Peng Wenbo;Wu Zhenglei;Xiong Fujun;Zhao Hongliang(Jiangsu Jiuwu Hi-Tech Co., Ltd., Nanjing 211808, China)
出处 《广东化工》 CAS 2018年第11期99-101,共3页 Guangdong Chemical Industry
关键词 硅铝粉体 陶瓷膜 膜清洗 silicon aluminum powder membrane cleaning ceramic membrane
  • 相关文献

参考文献5

二级参考文献37

  • 1张健,岳敏.单个气泡在加压液-固流化床中上升速度的模型与计算[J].应用基础与工程科学学报,2000,8(1):78-83. 被引量:2
  • 2邹国发,龙国荣,万建平,严旭,陆榕海,马军.树脂基复合材料蜂窝夹层结构修补技术研究[J].玻璃钢/复合材料,2005(6):42-44. 被引量:10
  • 3[1]Ghiorse S R. Effect of Void Content on The Mechanical Properties of Carbon/Epoxy Laminates SAMPE Q., 1993, 24(2): 54 ~ 59
  • 4[2]Bowies K J, Frimpong S J. Void Effects on the Interlaminar Shear Strength of Unidirectional Graphite-Fiber-Reinforced Composites.Composite Mater., 1992, 26( 10): 1487 ~ 1509
  • 5[3]Bascom W D, Romans J B. Micro Voids in Glass-Resin Composite. Ind. Eng. Chem. Prod. Res. Dev., 1968, 7:172 ~ 178
  • 6[4]Kohn E J, Sands A G, and Clark R C. Quantitative Measurement of Void Content in Glass-Filament-Wound Composites and Correlation of Interlaminar Shear Strength with Void Content.Ind. Eng. Chem. Prod. Res. Dev., 1968, 7:179 ~ 183
  • 7[5]Rohatgi V, Patel N, and L James Lee. Experimental Investigation of Flow-Induced Mierovoids During Impregnation of Unidirectional Stitched Fiberglass Mat. Polymer Composite, 1996, 17(2): 161 ~ 170
  • 8[6]Yung-Tin Chen, Davis H T, and Macosko W. Wetting of Fiber Mat for Composites Manufacturing: I. Visualizition Experiments. AICHE J.,1995, 41 (10): 2261 ~ 2273
  • 9[7]Parnas R S, Frederick R, and Phelan Jr. The Effect of Heterogeneous Porous Media on Mold Filling in Resin Transfer Molding. SAMPE Q., 1991,22:35 ~ 60
  • 10[8]Chan A W, Morgan F J. A Model on Formation of Rod-Like Voids in Fiber Tows. SAMPE Q., 1993, 24:49 ~ 536

共引文献37

同被引文献41

引证文献3

二级引证文献4

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部