摘要
Hierarchical zeolite materials were prepared via one‐pot synthesis of ZSM‐11zeolites with different molar ratios(R)of a mesoporogen,i.e.,cetyltrimethylammonium bromide template(CTAB),to a microporogen,i.e.,tetra‐n‐butylammonium bromide(TBABr).The structures,morphologies,and textural properties of the resultant materials were investigated.Initially,with increasing R,the crystal size of the synthesized product decreased,the number of intercrystalline mesopores increased,and a pure ZSM‐11zeolite phase was present.Then an MCM‐41‐like phase was produced and embedded in the ZSM‐11zeolite phase.Finally,an MCM‐41‐like phase was obtained.The alkalinity had important effects on the physicochemical and textural properties of the prepared samples.A possible mechanism of formation of the hierarchical ZSM‐11zeolite was proposed on the basis of a combination of various characterization results.The role of CTAB varied depending on the R value,and it showed a capping effect,micellar effect,and template effect.These effects of CTAB were synergetic in ZSM‐11synthesis,but they were competitive with the structure‐directing effect of TBABr.In addition,the impact of the acidic properties and porosities of the hierarchical ZSM‐11catalysts on their performances in the alkylation of benzene with dimethyl ether was investigated.?2018,Dalian Institute of Chemical Physics,Chinese Academy of Sciences.Published by Elsevier B.V.All rights reserved.
ZSM-11与ZSM-5分子筛具有相似的孔道结构,通常表现出相似的催化性能,但近年来的研究发现,ZSM-11分子筛在某些反应过程具有明显优于ZSM-5的催化性能,因而逐渐引起科研界和工业界的广泛重视.但受其微孔尺寸的限制,在使用过程中往往容易积碳,并导致快速失活.为此,向微孔体系引入介孔制备多级孔ZSM-11分子筛是一种规避上述问题的有效方式.我们研究组前期已对分子筛进行碱处理脱硅及在该体系中加入CTAB制备多级孔分子筛进行了系统研究.在此基础上本文通过改变介孔模板剂十六烷基三甲基溴化铵(CTAB)和微孔模板剂四丁基溴化铵(TBABr)的摩尔比(R),采用一步法制备了一系列多级孔ZSM-11分子筛材料,并通过多种表征手段对材料的性质进行了系统研究.随着R值的增加,广角XRD测试结果表明,产物的结晶度逐渐下降,同时小角XRD测试结果表明产物中逐渐产生有序介孔相;XRF测试结果表明,产物的总包硅铝比呈上升趋势;SEM表征结果表明,首先棒状纳米晶团聚体形貌的ZSM-11分子筛的晶粒尺寸逐渐降低,随后晶粒之间插入无定形样品,直至最终产物几乎完全为无定形材料构成;TEM图片与上述表征结果一致,样品初始晶格条纹清晰且晶粒边缘规整,随后晶粒边缘开始弯曲不平,接着晶体样品中开始产生有序介孔材料,最终几乎完全变为有序介孔材料.综合上述表征结果和相关文献可推测,该有序介孔材料为类MCM-41材料.另外,我们采用N_2物理吸附对材料的织构性质进行了考察,发现随着R值增大,产物的微孔减少,介孔增多.然而TEM结果表明,在类MCM-41产生之前,样品中介孔的增多并非来源于晶内孔,而是来源于晶粒之间的堆积孔,这是由于在合成过程中CTAB胶束嵌入ZSM-11的晶粒之间所导致.合成体系的碱度对产物的物化性质和织构性质也起了非常重要的作用.我们将这个体系与NaOH+CTAB对分子筛进行脱硅后处理体系进行了对比,发现虽然前者只能产生晶间孔而后者可产生晶内孔,但碱度对两者的作用相似,即降低碱度均可导致类MCM-41有序介孔相的产生.此外,还通过NH_3-TPD和Py-IR技术对材料的酸性进行了考察.基于上述研究结果,提出了多级孔ZSM-11分子筛的形成机理.随着R值的变化,CTAB分别起了覆盖效应、胶束效应和模板效应.这些效应在合成多级孔ZSM-11分子筛过程中相互协同,同时又与TBABr的结构导向效应相互竞争,进而影响合成产物的孔结构、形貌、酸性以及用于二甲醚和苯烷基化的催化性能.
