期刊文献+

数字化技术在口腔上前牙区种植修复中的临床研究 被引量:19

Clinical research of digital design in implant rehabilitation of oral maxillary anterior teeth area
下载PDF
导出
摘要 目的评价数字化技术在口腔上前牙区种植修复中应用的临床效果。方法选取拟行种植修复的上前牙缺失患者,向患者详细介绍治疗方案后由患者自主选择,最终确定选择数字化种植修复患者8人作为实验组,选择传统种植修复患者10人作为对照组,分别对两组的种植体偏倚、修复体初戴时间及修复后满意度进行评价。结果实验组与对照组种植体的颈部偏移无明显差异[(0.85±0.19)mm vs(1.08±0.22)mm,P>0.05],实验组种植体根部偏移小于对照组[(0.91±0.20)mm vs(1.75±0.31)mm,P<0.05]。实验组每单位修复体初戴调改时间少于对照组[(8.9±2.1)min vs(19.0±5.7)min,P<0.05],且实验组患者对修复体及修复后面部整体外观满意度高于对照组(P<0.05)。结论数字化技术的应用能够精确种植,有助于缩短修复体初戴时间,并提高患者对种植修复效果的满意度。 Objective To evaluate the clinical efficacy of digital design in implant rehabilitation of oral maxillary anterior teeth area.Methods Patients with maxillary anterior teeth missing who needed implant surgery were chosen and divided into experimental group and control group according to their will after detailed introduction of the treatment plan.Finally 8 patients undergoing digital implant rehabilitation were chosen as experimental group,and 10 patients undergoing traditional implant rehabilitation were chosen as control group.The deviation of implants,time consuming in the first insertion and patient’s satisfaction rate were compared between two groups.Results There was no significant difference in neck deviation between experimental groupand control group[(0.85±0.19)mm vs(1.08±0.22)mm,P>0.05].The apical deviation in experimental group was less than that in control group[(0.91±0.20)mm vs(1.75±0.31)mm,P<0.05].The time consuming in the first insertion in experimental group was shorter than that in control group[(8.9±2.1)min vs(19.0±5.7)min,P<0.05].The satisfaction rate in experimental group was significantly higher than that in control group(P<0.05).Conclusion The application of digital design could reach the precise implant,shorten the time consuming of restoration,and improve the patient’s satisfaction rate.
作者 范亚伟 孙福星 张鹏飞 FAN Yawei;SUN Fuxing;ZHANG Pengfei(Department of Stomatology,First Hospital of Shanxi Medical University,Taiyuan 030001,China;Department of Oral and Maxillofacial Surgery,Stomatological Hospital of Shanxi Medical University)
出处 《山西医科大学学报》 CAS 2018年第7期870-873,共4页 Journal of Shanxi Medical University
关键词 数字化技术 种植导板 口内扫描 种植 修复 digital design implant plate introal scanning implant restoration
  • 相关文献

参考文献4

二级参考文献38

  • 1黄晋杰,谭建国,栾庆先.计算机图像处理技术在前牙美学修复中的应用[J].中华口腔医学杂志,2007,42(7):387-390. 被引量:11
  • 2Pani St_;, Hedge AM. Impressions in cleft lip and palate: a novel lwo slage technique. J Clin Pediatr Dent, 2008,33 (2) :93-96.
  • 3Mormann WH. The evolution of the CEREC system. J Am Dent Assoc,2006,137 Supph7S-13S.
  • 4Scotti R, Cardelli P, Baldissara P, et al. Clinical fitting of CAD/CAM zirconia single crowns generated from digital intraoral impressions based on active wavefront sampling. J Dent,2011,17.
  • 5Kachalia PR, Geissberger MJ. Dentistry a la carte: in of{ice CAD/CAM technology. J Calif Dent Assoc, 2010, 38 (5) : 323-330.
  • 6Tsitrou EA, Helvatjoglu-Antoniades M, van Noort R. A preliminary evaluation of the structural integrity and fracture mode of minimally prepared resin bonded CAD/CAM crowns. J Dent,2010,38(1) : 16-22.
  • 7da Costa JB, Pelogia F, Hagedorn B, et al. Evaluation of different methods of optical impression making on the marginal gap of onlays created with CEREC 3D. Oper Dent, 2010,35(3):324-329.
  • 8Persson AS, Oden A, Andersson M, et al. Digitization of simulated clinical dental impressions: virtual three dimensional analysis of exactness. Dent Mater, 200, 25 ( 7 ) 929-936.
  • 9Wiranto MG, Engelbrecht WP, Tutein Nokhenius HE,et al. Validity, reliability, and reproducibility of linear measurements on digital models obtained from intraoral and cone-beam computed tomography scans of alginate impressions. Am J Orthod Dentofacial Orthop, 2013,143 ( 1 ) : 140-147.
  • 10Cuperus AM, Harms MC;, Rangel FA, et al. Dental models made with an intraoral scanner: a validation study. Am J Orthod Dentofacial Orthop, 2012,142(3) : 308-313.

共引文献117

同被引文献143

引证文献19

二级引证文献112

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部