期刊文献+

基于Smith预估器的热轧监控AGC研究 被引量:1

Research on Monitor AGC of Hot Rolling Mill Based on Smith Predictor
下载PDF
导出
摘要 本文针对热轧生产线由于厚度仪与轧机机架存在的物理距离导致的检测滞后问题给带钢成品厚度的影响进行研究,采用Smith预估器来消除滞后对厚度控制的影响。首先,介绍Smith补偿的原理。其次,给出监控厚度控制(Monitor Automatic Gauge Control MAGC)原理。再次,将Smith补偿与监控AGC相结合,避免了由于检测滞后给厚度造成的不良影响。最后,通过仿真可以看出采用Smith预估器补偿的方法能够有效提升带钢的厚度控制精度。 In this paper,due to the physical distance between the gauge and the mill stand,the influence of the detection delay on the thickness of the finished strip is studied,and the Smith predictor is used to eliminate the influence of the delay on the thickness control.Firstly,the principle of Smith compensation is introduced.Secondly,the control principle of monitoring AGC is given.Thirdly,the Smith compensation is combined with the monitoring AGC to avoid the bad influence on the thickness caused by the detection delay.Finally through the simulation,we can see that the Smith predictor compensation method can effectively improve the thickness control accuracy of the strip.
作者 田超 韩永成 高丹 TIAN Chao;HAN Yong-cheng;GAO Dan(Tangshan Polytechnic College,Tangshan Hebei 063299)
出处 《数字技术与应用》 2020年第5期5-5,7,共2页 Digital Technology & Application
关键词 SMITH预估器 厚度自动控制(AGC) 纯滞后 Smith predictor automatic gain control time delay
  • 相关文献

参考文献2

二级参考文献10

  • 1Guesalaga A. Modelling end-of-roll dynamics in positioning ser- vos[J]. Control Engineering Practice, 2004,45 (12) : 217.
  • 2Garciia P, Santos T, Normey Rico J E, et al. Smith predictor- based control schemes for dead-time unstable cascade processes [J]. Industrial and Engineering Chemistry Research, 2010,49 (22) :11471.
  • 3Kaya I. IMC based automatic tuning method for PID control- lers in a Smith predictor configuration [J]. Computers and Chemical Engineering, 2004,28(3) : 281.
  • 4Hideki Yanada, Kazumasa Furuta. Adaptive control of an elec- tro-hydraulic servo system utilizing online estimate of its natu- ral frequency [J]. Meehatronics, 2007,17(6) : 337.
  • 5Sadeghieh A, Sazgar H, Goodarzi K, et al. Identification and real-time position control of a servo-hydraulic rotary actuator by means of a neurobiologically motivated algorithm[J]. ISA Transactions, 2012 (51) :208.
  • 6Albayrak M, Allahverdi N. Development a new mutation oper- ator to solve the traveling salesman problem by aid of genetic algorithms [J]. Expert Systems with Applications, 2011,38 (3) :1313.
  • 7姚建勇,焦宗夏,黄澄.基于动态逆模型的电液位置伺服系统复合控制[J].机械工程学报,2011,47(10):145-151. 被引量:20
  • 8孙权,何建忠,王文华.双输入双输出时滞过程解耦Smith控制[J].计算机系统应用,2012,21(3):59-62. 被引量:2
  • 9马永杰,云文霞.遗传算法研究进展[J].计算机应用研究,2012,29(4):1201-1206. 被引量:432
  • 10黄长清,赵旻.冷轧板带板形识别及控制的研究进展[J].钢铁研究学报,2013,25(12):1-7. 被引量:18

共引文献2

同被引文献9

引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部