换流变有载分接开关非电量保护优化配置试验研究被引量：13

Experimental Study on Optimal Configuration of Pressure Relief Device,Pressure and Oil Flow Relay of On-load Tap-changer

下载PDF

导出

摘要基于有载分接开关油室进行研发改造,搭建了短路燃弧试验平台并开展了16次短路燃弧试验,基于试验结果分析,提出压力释放阀投报警、油流继电器投跳闸的有载分接开关非电量保护装置标准化配置建议方案。 Based on the R&D and transformation of the oil compartment of the OLTC,a short-circuit arc test platform is built and 16 short-circuit arc tests are carried out.Based on the analysis of the test results,the on-load points for the pressure release valve to alarm and the oil flow relay to trip were proposed.Proposal for standardized configuration of non-electrical switch protection devices.

作者徐海军王进廖文锋陕华平王佳妮 XU Hai-jun;WANG Jin;LIAO Wen-feng;SHAN Hua-ping;WANG Jia-ni(DC Technical Center of State Grid Corporation of China,Beijing 100052,China;North China Electric Power University,Beijing 102206,China)

机构地区国家电网有限公司直流技术中心华北电力大学经济与管理学院

出处《变压器》 2021年第10期48-52,共5页 Transformer

基金国家电网有限公司总部管理科技项目资助-国内外分接开关制造运行经验统计分析研究(项目编号:5500-202049355A-0-0-00)。

关键词有载分接开关内部燃弧试验压力释放阀继电器 On-load tap-changer Internal arcing test Pressure relief device Relay

分类号 TM403.4 [电气工程—电器]

引文网络
相关文献

参考文献9

1耿伟,耿洁宇.变压器有载分接开关常见问题的分析和处理[J].变压器,2012,49(3):71-72. 被引量：18
2江丹宇,吕鹏瑞,韦教玲,万书亭,马志钦.瞬态油流冲击下气体继电器动作特性试验研究[J].变压器,2021,58(2):57-61. 被引量：10
3周显宏,周永明,陈桂芬,姜世凯,振玉民.压力释放阀动作性能的试验研究[J].变压器,2001,38(12):38-42. 被引量：7
4乔小冬,阎乃臣.换流变压器油流继电器故障原因分析[J].电世界,2018,59(1):14-17. 被引量：1
5闫晨光,郝治国,张保会,郑涛.电力变压器油箱形变破裂建模及仿真[J].电工技术学报,2016,31(3):180-187. 被引量：23
6闫晨光,张保会,郝治国,晁光,王龙,付科源,梁栋.电力变压器油箱内部故障压力特征建模及仿真[J].中国电机工程学报,2014,34(1):179-185. 被引量：40
7万利,胡红,王乃会,范敏,周小军.一起束缚电阻导致的变压器有载分接开关故障案例分析[J].变压器,2020,57(12):83-87. 被引量：14
8周海滨,刘观伟,颜晓江.换流变压器有载分接开关切换过程油流涌动仿真研究[J].变压器,2020,57(2):26-30. 被引量：16
9张晋寅,潘志城,周海滨,邓军.基于振动测试的真空有载分接开关故障诊断研究[J].变压器,2020,57(11):56-59. 被引量：17

二级参考文献69

1王雪,王增平.变压器内部故障仿真模型的设计[J].电网技术,2004,28(12):50-52. 被引量：43
2赵彤,李庆民,陈平.OLTC振动信号特征提取的动力学分析方法[J].电工技术学报,2007,22(1):41-46. 被引量：35
3张保会.电力系统继电保护[M].2版.北京:中国电力出版社,2009.
4Abi-Samra N,Arteaga J,Darovny B,et al.Power transformer tank rupture and mitigation:a summary of current state of practice and knowledge by the task force of IEEE power transformer subcommittee[J].IEEE Transactions on Power Delivery,2009,24(4):1959-1967.
5Mahieu W R.Prevention of high fault ruptures of pole-type distribution transformers[J].IEEE Transactions on Power Apparatus Systems,1975,94(5):1698-1707.
6Foata M,Iordanescu M,Hardy C.Computational methods for the analysis of explosions in oil-insulated electrical equipment[J].IEEE Transactions on Power Systems,1988,3(1):186-293.
7Hamel A,Dastous J-B,Foata M.Estimating overpressures in pole-type distribution transformers,part I:tank withstand evaluation[J].IEEE Transactions on Power Delivery,2003,18(1):113-119.
8Dastous J-B,Foata M,Hamel A.Estimating overpressures in pole-type distribution transformers,part II:prediction tools[J].IEEE Transactions on Power Delivery,2003,18(1):120-127.
9Muller S,Brady R.Prevention of transformer tank explosion,part 1:experimental tests on large transformers[C]//2008 ASME Pressure Vessels and Piping Division Conference.Chicago,USA:ASME,2008:357-365.
10Brady R,Muller S.Prevention of transformer tank explosion,part 2:development and application of a numerical simulation tool[C]//2008 ASME Pressure Vessels and Piping Division Conference.Chicago,USA:ASME,2008:49-58.