期刊文献+

风电机组螺栓复用扭矩系数变化的研究 被引量:1

Study on Reuse Torque Coefficient of Bolt of Wind Turbine
下载PDF
导出
摘要 为提高风电紧固件使用效率,从而降低风电机组成本,对风机用高强度紧固件重复使用扭矩系数进行研究。以8组螺栓连接副为研究对象,对其进行10次装-拆拧紧试验用以模拟风机螺栓的重复使用,并在拧紧过程中记录连接副的螺纹摩擦系数、端面摩擦系数、扭矩系数。通过对试验结果的分析发现:螺栓连接副端面摩擦系数和螺纹摩擦系数均随着拧紧次数的增加呈先增后减的趋势;当重复拧紧超过5次后螺纹摩擦系数和端面摩擦系数趋于平稳略低于第1次拧紧摩擦系数;在10次拧紧过程中螺栓连接副的扭矩系数最大值为第1次拧紧扭矩系数的106.8%,最小值为第1次拧紧扭矩系数的94.7%,满足设计要求,可重复使用。 In order to improve the use efficiency of wind power fasteners and reduce the cost of wind turbine,the reuse torque coefficient of high-strength fasteners for wind turbine is studied.Taking 8 groups of bolt connection pairs as the research object,10 assembly disassembly and tightening tests were carried out to simulate the reuse of wind turbine bolts,and the thread friction coefficient,end face friction coefficient and torque coefficient of the connection pairs were recorded during the tightening process.Through the analysis of the test results,it is found that the end face friction coefficient and thread friction coefficient of bolt connection pair show a trend of first and then decreasing with the increase of tightening times;When repeated tightening for more than 5 times,the thread friction coefficient and end face friction coefficient tend to be stable,slightly lower than the friction coefficient of the first tightening;In the process of 10 tightening,the maximum torque coefficient of the bolt connection pair is 106.8%of the first tightening torque coefficient,and the minimum value is 94.7%of the first tightening torque coefficient,which meets the design requirements and can be reused..
作者 郑国龙 刘河 杨炯明 张紫平 ZHENG Guo-Long;LIU He;YANG Jiong-Ming;ZHANG Zi-Ping(Goldwind Science&Creation Windpower Equipment Co.,Ltd.,Beijing100176,China)
出处 《机电产品开发与创新》 2022年第1期124-126,130,共4页 Development & Innovation of Machinery & Electrical Products
关键词 风电机组 紧固件 复用 扭矩系数 Wind turbine Fasteners Reuse Torque coefficient
  • 相关文献

参考文献3

二级参考文献21

  • 1张伟明.达克罗──当今世界表面处理的高新技术[J].材料保护,1995,28(8):19-20. 被引量:44
  • 2风机倒塌原因探讨[EB/OL].http://www.cnwpem.corn/web.php?wid=22&cid=9220&page=O,2011-04-25.
  • 3Germanischer Lloyd Industrial Services GmbH. GL-Wind 2010, Guideline for the Certification of Wind Turbine IS]. Germany: Germanischer Lloyd Industrial Services GmbH, 2010:13-14.
  • 4GB/T3098.1-2010.紧固件机械性能螺栓、螺钉和螺柱[S].北京:中国标准出版社.2011.
  • 5Execution of Steel Structures and Aluminium Structures - Part 2: Technical Requirements for Steel Structures[S]; German Version EN 1090-2:2008+A1:2011.
  • 6GB/T1231-2006.钢结构用高强度大六角头螺栓、大六角头螺母、垫圈技术条件[S].北京:中国标准出版社,2006.
  • 7DIN18800-7-2008.Steel Structures - Part 7: Execution and Constructor's Qualification [S]. German: Standardization Institute.
  • 8JGJ82-2011,钢结构高强度螺栓连接技术规程[S].北京:中国建筑工业出版社.2011.
  • 9周留霞.高压螺栓液压上紧装置的使用与上紧油压的计算[J].甘肃科技,2008,24(6):68-68. 被引量:2
  • 10钟盛钢,张先鸣.风电用与钢结构用高强度紧固件的差异[J].金属制品,2009,35(6):62-65. 被引量:11

共引文献13

同被引文献5

引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部