期刊文献+

某液传轨道工程车动力传动系统扭振分析

Torsional vibration analysis of the power transmission system in a hydraulic rail engineering vehicle
下载PDF
导出
摘要 扭转振动是动力传动系统重要的振动形式,特别是对于动力传递路径较长的轨道工程车。文章针对某液传轨道工程车的动力传动系统,建立多刚体扭振模型,分析了系统自由扭振和强迫扭振特性,对比了有无扭转减振器时曲轴的振动响应,研究了弹性联轴节参数对系统扭振响应的影响。结果表明,单节点弹联模态是频率最低的扭转模态,当联轴节扭转刚度小于0.0057MN∙m/rad时,单节点的联轴节扭振模态能避开工作转速范围内所有谐次的干扰力矩的共振点;曲轴前端扭转角位移、扭转应力随着发动机转速的升高而增大,加装扭转减振器可以明显减小曲轴扭振响应;怠速时(600r/min),联轴节相对阻尼系数在0.5~2.0范围内能明显改善输出力矩不均匀性,而高速时(1800r/min),较小的联轴节阻尼系数有利于改善输出力矩不均匀性。为了兼顾怠速与高速工况,联轴节相对阻尼系数尽量取小一些,比如取0.5。 Torsional vibration represents a crucial aspect of vibration in power transmission systems,especially for rail engineering vehicles featuring long power transmission pathways.In this study,a multi-rigid-body torsional vibration model was created for the power transmission system of a hydraulic rail engineering vehicle.The analysis focused on the free and forced torsional vibration characteristics of the system.A comparison was conducted on the vibration responses of crankshafts with or without a torsional damper.Further study delved into the influence of elastic coupling parameters on the system's torsional vibration responses.The results highlight the single-node elastic coupling mode as the torsional mode with the lowest frequency.In the single-node torsional vibration mode,couplings with a torsional stiffness less than 0.0057 MN·m/rad are determined to effectively avoid resonance points from disturbance torques across all harmonics within the operational speed range.Torsional angular displacements at the crankshaft front end and torsional stress levels exhibit an increase with rising engine speeds.The introduction of a torsional damper lead to a significant reduction in the torsional vibration responses of the crankshaft.At idle speed(600 r/min),controlling the relative damping coefficient of couplings between 0.5 and 2.0 significantly reduces the output torque inequality,while at high speeds(1800 r/min),a lower damping coefficient is conducive to mitigating this inequality.In order to adapt to both idle and high-speed conditions,it is recommended to keep the relative damping coefficient of couplings as minimal as possible,such as 0.5.
作者 徐坤 雒耀祥 张亚禹 李华伟 XU Kun;LUO Yaoxiang;ZHANG Yayu;LI Huawei(Xi'an R&D Center,Baoji CRRC Times Engineering Machinery Co.,Ltd.,Xi'an,Shaanxi 710000,China)
出处 《机车电传动》 2024年第3期70-78,共9页 Electric Drive for Locomotives
关键词 液力传动 轨道工程车 动力传动系统 扭振 hydraulic rail engineering vehicle power transmission system torsional vibration
  • 相关文献

参考文献14

二级参考文献56

  • 1王文平,项昌乐,刘辉.履带车辆动力传动系统扭振的时域仿真研究[J].中国机械工程,2006,17(17):1865-1868. 被引量:6
  • 2计晨,曾凡明.舰船复杂轴系扭振计算的通用模型及系统矩阵法研究[J].船海工程,2006,35(4):55-57. 被引量:9
  • 3重庆大学.SC6350C/SC1020汽车振动及噪声控制研究报告[R].2002.
  • 4陈之炎.轴系振动[M].上海:上海交通大学出版社,1991.
  • 5Klaus Steinel.Clutch tuning to optimize noise and vibration behavior in trucks and buses K[J].Steinel SAE Technical Paper 2000-01-3292E.
  • 6Johson O,Hirami N.Diagnosis and objective evaluation of gear rattle[A].Noise & Vibration Conference and Exposition SAE Technical Paper 911082.
  • 7MA Hongwen. Powershift steering transmission dynamic simulation study on vehicle straight-line running condition [Ph D Thesis]. Beijing:Beijing Institute of Technology, 2003 ( In Chinese) (马洪文. 车辆综合传动装置直驶工况动力学仿真研究[博士学位论文].北京:北京理工大学,2003).
  • 8庞剑.汽车噪声与振动[M].北京:北京理工大学出版社,2006:236-245.
  • 9韩树,王志达.摆盘发动机轴系扭转振动研究[J]噪声与振动控制,1987(06).
  • 10Niaool J, Swiatoniowski A. Numerical analysis of the vertical vibrations of rolling mills and their negative effect on the sheet quality [ J ]. Journal of Materials Processing Technology, 2005, 162(15) :546 -550.

共引文献79

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部