期刊文献+

Interfacial bonding state on different metals Ag, Ni in cold pressure welding

Interfacial bonding state on different metals Ag, Ni in cold pressure welding
下载PDF
导出
摘要 The interfacial bonding state for the different metals Ag, Ni without metallurgic are actions was studied. The tensile test of the joint concludes that the bonding strength of Ag,Ni in cold pressure welding is strong enough to satisfy the demand of application, while the value of bonding strength is larger than that of Ag base. The conclusions further signify that the metals(hardly being mutual soluble) can be welded, and supply extremely important references to the further study either on test or theory for the weldability of different metals. The theoretical analysis and calculations of the bonding strength were made on the base of thermodynamics, crystallography, solid physics etc. Moreover, by means of microscopic test and analysis, especially drawing support from the research of Al Pb, this strong bonding mainly depends on the mechanical bonding power and metal atomic linkage, but not on the atomic diffusion. The interfacial bonding state for the different metals Ag, Ni without metallurgic are actions was studied. The tensile test of the joint concludes that the bonding strength of Ag,Ni in cold pressure welding is strong enough to satisfy the demand of application, while the value of bonding strength is larger than that of Ag base. The conclusions further signify that the metals(hardly being mutual soluble) can be welded, and supply extremely important references to the further study either on test or theory for the weldability of different metals. The theoretical analysis and calculations of the bonding strength were made on the base of thermodynamics, crystallography, solid physics etc. Moreover, by means of microscopic test and analysis, especially drawing support from the research of Al Pb, this strong bonding mainly depends on the mechanical bonding power and metal atomic linkage, but not on the atomic diffusion.
出处 《中国有色金属学会会刊:英文版》 CSCD 2003年第2期276-279,共4页 Transactions of Nonferrous Metals Society of China
关键词 冷压焊 界面结合状态 焊接 metallurgic reactions cold pressure welding interface bonding
  • 相关文献

参考文献2

二级参考文献15

  • 1S. Kúdela,V. Gergely,L. Smr?ok,S. Oswald,S. Baunack,K. Wetzig. Phase transformations of δAl2O3 (Saffil) fibres during their interaction with molten MgLi alloys[J] 1996,Journal of Materials Science(6):1595~1602
  • 2S. Kúdela,V. Gergely,A. Schweighofer,S. Baunack,S. Oswald,K. Wetzig. The δ-Al2O3 (Saffil) fibre degradation during infiltration with MgLi alloy[J] 1994,Journal of Materials Science(19):5071~5077
  • 3S. Kudela,V. Gergely,E. J?nsch,A. Hofmann,S. Baunack,S. Oswald,K. Wetzig. Compatibility between PAN-based carbon fibres and Mg8Li alloy during the pressure infiltration process[J] 1994,Journal of Materials Science(21):5576~5582
  • 4G. Gonzalez-doncel,J. Wolfenstine,P. Metenier,O. A. Ruano,O. D. Sherby. The use of foil metallurgy processing to achieve ultrafine grained Mg-9 Li laminates and Mg-9Li-5B4C particulate composites[J] 1990,Journal of Materials Science(10):4535~4540
  • 5J. F. Mason,C. M. Warwick,P. J. Smith,J. A. Charles,T. W. Clyne. Magnesium-lithium alloys in metal matrix composites — A preliminary report[J] 1989,Journal of Materials Science(11):3934~3946
  • 6Stalmans R,van Humbeeck J and Delaey L.An introduction to martensite and shape memory[].Acta Metallurgica et Materialia.1992
  • 7Tautzenberger P.Thermoactuators: A comparison of shape memory alloys thermostatic bimetals and wax actuators[].Engineering Aspects of SMA.1990
  • 8Perkins J.The two way memory effect (TWME)[].Engineering Aspects of SMA.1990
  • 9Liu Y and McCormick P G.The science and technology of shape memory alloys[].Acta Metallurgica et Materialia.1998
  • 10Morris M A and Lipe T.Ductility and two-way memory effect associated with stress-induced martensite stability produced by deformation of CuAlNi alloys[].Proc Intern Conf on Martensitic Transformations.1993

共引文献16

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部