期刊文献+

复合工质真空相变元件的传热特性 被引量:1

Heat transfer characteristics of vacuum phase-change component with complex working medium
下载PDF
导出
摘要 对新型复合工质真空相变元件传热特性进行了实验研究,得出了传热特性实验关系式。确定了新型复合工质元件的最佳倾角为30°和充液率为18%。该实验研究为新型复合工质真空相变装置及其系统的设计提供了依据。 An experimental study has been taken to determine the heat transfer characteristics of vacuum phasechange component with complex working medium and empirical expressions have been derived.The results show that the optimum inclination angle of the component is 30°,its filling rate is 18%.This paper provides basis for the design of vacclum phasechange heating system.
出处 《吉林大学学报(工学版)》 EI CAS CSCD 北大核心 2003年第3期42-45,共4页 Journal of Jilin University:Engineering and Technology Edition
关键词 真空相交元件 复合工质 倾角 充液率 传热特性 vacuum phase-change component complex working medium inclination angle filling rate heat transfer characteristics
  • 相关文献

参考文献2

  • 1李亭寒 华诚生.热管设计与应用[M].北京:化学工业出版社,1988..
  • 2刘效洲.混合工质热管热工特性的研究[M].长春:吉林工业大学汽车工程学院,1998..

共引文献1

同被引文献13

  • 1闫相桥.轮胎硫化过程的有限元分析技术研究[M].哈尔滨:哈尔滨工业大学出版社,2001.
  • 2Yan Xiang-qiao.Numerical modeling of dynamic cu-ring process of tire by finite element[J].PolymerJournal,2007,39(10),1001-1010.
  • 3Toth W J,Chang J P,Zanichelli C.Finite elementevaluation of the state of cure in a tire[J].Tire Sci-ence and Technology,1991,19(4):178-212.
  • 4Antonucci V,Giordano M,Hsiao K T,et al.Amethodology to reduce thermal gradients due to theexothermic reactions in composites processing[J].International Journal of Heat and Mass Transfer,2002,45(8):1675-1684.
  • 5张建,王国林,唐文献,等.一种模拟全钢子午线轮胎硫化过程的方法[P].中国:201110143542.0,2011-10-19.
  • 6Rafei M,Ghoreishy M H R,Naderi G.Develop-ment of an advanced computer simulation techniquefor the modeling of rubber curing process[J].Com-putational Materials Science,2009,47(2):539-547.
  • 7Isayev A I,Deng J S.Nonisothermal vulcanizationof rubber compounds[J].Rubber Chemistry andTechnology,1988,61(1):340-361.
  • 8Arrillaga A,Zaldua A M,Atxurra R M,et al.Techniques used for determining cure kinetics ofrubber compounds[J].European Polymer Journal,2007,43(11):4783-4799.
  • 9Ghoreishy M H R.Numerical Simulation of the Cu-ring Process of Rubber Articles[M].W.U.Oster(Ed.),Computational Materials Nova Science Pub-lishers,New York,2009:445-478.
  • 10ABAQUS Inc.ABAQUS example problems manual[M].USA:ABAQUS Inc,2007.

引证文献1

二级引证文献5

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部