Preparation of a zeolite-palladium composite membrane for hydrogen separation:Influence of zeolite film on membrane stability

With the development of hydrogen energy,palladium-based membranes have been widely used in hydrogen separation and purification.However,the poor chemical stability of palladium composite membranes limits their commercial applications.In this study,a zeolite-palladium composite membrane with a sandwich-like structure was obtained by using a TS-1 zeolite film grown on the surface of palladium membrane.The membrane microstructure was characterized by SEM and EDX.The effects of the TS-1 film on the hydrogen permeability and stability of palladium composite membrane were investigated in details.Benefited from the protection of the TS-1 zeolite film,the stability of palladium composite membrane was enhanced.The results indicate that the TS-1-Pd composite membrane was stable after eight cycles of the temperature exchange cycles between 773 K and 623 K.Especially,the loss of hydrogen permeance for TS-1-Pd composite membrane was much smaller than that of the pure palladium membrane when the membrane was tested in the presence of C3H6atmosphere.It indicated that the TS-1-Pd composite membrane had better chemical stability in comparison with pure palladium membrane,owing to its sandwich-like structure.This work provides an efficient way for the deposition of zeolite film on palladium membrane to enhance the membrane stability.

Low palladium content CeO_(2)/ZnO composite for acetone sensor with sub-second response prepared by ultrasonic method

In practical applications,noble metal doping is often used to prepare high performance gas sensors,but more noble metal doping will lead to higher preparation costs.In this study,CeO_(2)/ZnO-Pd with low palladium content was prepared by ultrasonic method with fast response and high selectivity for acetone sensing.With the same amount of palladium added,the selectivity coefficient of CeO_(2)/ZnO-Pd is 1.88 times higher than that of the stirred sensor.Compared with the pure PdO-doped CeO_(2)/ZnO-PdO material,the content of Pd in CeO_(2)/ZnO-PdO is about 30%of that in CeO_(2)/ZnO-PdO,but the selectivity coefficient for acetone is 2.56 times higher.The CeO_(2)/ZnO-Pd sensor has a higher response(22.54)to 50×10^(−6) acetone at 300℃and the selectivity coefficient is 2.57 times that of the CeO_(2)/ZnO sensor.The sensor has a sub-second response time(0.6 s)and still has a 2.36 response to 330×10^(−9) of acetone.Ultrasonic doping makes Pd particles smaller and increases the contact area with gas.Meanwhile,the composition of n-p-n heterojunction and the synergistic effect of Pd/PdO improve the sensor performance.It shows that ultrasonic Pd doping provides a way to improve the utilization rate of doped metals and prepare highly selective gas sensors.

Controlling Reactivity of Palladium Amides for Selective Carbonylation towards Urea and Oxamide Derivatives

Carbonylation reactions,crucial for carbonyl group incorporation,struggle with the inherent complexity of achieving selective mono-or double-carbonylation on single substrates,often due to competing reaction pathways.Herein,our study introduces a strategy employing palladium amides,harnessing their unique reactivity control,to direct the selective carbonylation of amines for the targeted synthesis of urea and oxamide derivatives.The palladium amide structure was elucidated using single-crystal X-ray diffraction.Controlled experiments and cyclic voltammetry studies further elucidate that the oxidation of palladium amide or its insertion into a carbonyl group diverges into distinct pathways.By employing sodium percarbonate as an eco-friendly oxidant and base,we have successfully constructed a switchable carbonylation system co-catalyzed by palladium and iodide under room temperature.The utilizing strategy in this study not only facilitates effective control over reaction selectivity but also mitigates the risk of explosions,a critical safety concern in traditional carbonylation methods.

MOF-assisted Synthesis of Dual-atom Palladium Catalysts for Acetylene Semi-hydrogenation

The selective removal of trace acetylene in ethylene feed gas is of great significance in the petrochemicalindustry;however, there are still challenges in designing and developing high-performance catalysts. Here, a MOFassistedencapsulation strategy was adopted for the precise synthesis of diatomic Pd2 sites on a ZnO support. When usedfor the acetylene semi-hydrogenation reaction, the dual-atom Pd2-ZnO catalyst exhibited improved catalytic performance,achieving complete conversion of acetylene at 125 °C with an 89% selectivity to ethene, as compared to Pd single-atom andnanoparticles. This enhancement was mainly attributed to the catalyst’s ability to dissociate H2 and facilitate the desorptionof intermediate C2H4. Moreover, the strong interaction between the support and the diatomic Pd sites was responsible for thecatalyst’s excellent stability during the long-term reaction.

Preparation of palladium-based catalyst by plasma-assisted atomic layer deposition and its applications in CO_(2) hydrogenation reduction

Supported Pd catalyst is an important noble metal material in recent years due to its high catalytic performance in CO_(2)hydrogenation.A fluidized-bed plasma assisted atomic layer deposition(FP-ALD) process is reported to fabricate Pd nanoparticle catalyst over γ-Al_(2)O_(3)or Fe_(2)O_(3)/γ-Al_(2)O_(3)support,using palladium hexafluoroacetylacetonate as the Pd precursor and H_(2)plasma as counter-reactant.Scanning transmission electron microscopy exhibits that highdensity Pd nanoparticles are uniformly dispersed over Fe_(2)O_(3)/γ-Al_(2)O_(3)support with an average diameter of 4.4 nm.The deposited Pd-Fe_(2)O_(3)/γ-Al_(2)O_(3)shows excellent catalytic performance for CO_(2)hydrogenation in a dielectric barrier discharge reactor.Under a typical condition of H_(2)to CO_(2)ratio of 4 in the feed gas,the discharge power of 19.6 W,and gas hourly space velocity of10000 h^(-1),the conversion of CO_(2)is as high as 16.3% with CH_(3)OH and CH4selectivities of 26.5%and 3.9%,respectively.

Inner-pore reduction nucleation of palladium nanoparticles in highly conductive wurster-type covalent organic frameworks for efficient oxygen reduction electrocatalysis

Covalent organic frameworks(COFs)have emerged as a class of promising supports for electrocatalysis because of their advantages including good crystallinity,highly ordered pores,and structural diversity.However,their poor conductivity represents the main obstruction to their practical application.Here,we reported a novel synthesis strategy for synergistically endowing a triphenylamine-based COFs with improved electrical conductivity and excellent catalytic activity for oxygen reduction,via the in-situ redox deposition and confined growth of palladium nanoparticles inside the porous structure of COFs using reductive triphenylamine frameworks as reducing agent;meanwhile,the triphenylamine unit was oxidized to radical cation structure and affords radical cation COFs with conductivity as high as3.2*10^(-1) S m^(-1).Such a uniform confine palladium nanoparticle on highly conductive COFs makes it an efficient electrocatalyst for four-electron oxygen reduction reaction(4e-ORR),showing excellent activities and fast kinetics with a remarkable half-wave potential(E_(1/2))of 0.865 V and an ultralow Tafel slope of 39.7 mV dec^(-1) in alkaline media even in the absence of extra commercial conductive fillers.The generality of this strategy was proved by preparing the different metal and metal alloy nanoparticles supported on COFs(Au@COF,Pt@COF,AuPd@COF,AgPd@COF,and PtPd@COF)using reductive triphenylamine frameworks as reducing agent.This work not only provides a facile strategy for the fabrication of highly conductive COF supported ORR electrocatalysts,but also sheds new light on the practical application of Zn-air battery.

Highly reactive and reusable heterogeneous activated carbons-based palladium catalysts for Suzuki-Miyaura reaction

Suzuki-Miyaura reaction of aryl halides with phenylboronic acid using a heterogeneous palladium catalyst based on activated carbons(AC) was systematically investigated in this work. Two different reaction modes(batch procedure and continuous-flow procedure) were used to study the variations of reaction processing. The heterogeneous catalysts presented excellent reactivity and recyclability for iodobenzene and bromobenzene substrates in batch mode, which can be attributed to stabilization of Pd nanoparticles by the thiol and amino groups on the AC supports. However, significant dehalogenation in the reaction mixture and Pd leaching from the heterogeneous catalysts were observed in continuous-flow mode.This unique phenomenon in continuous-flow mode resulted in a dramatic decline in reaction selectivity and durability of heterogeneous catalysts comparing with that of batch mode. In addition, the heterogeneous Pd catalysts with thiol-and amino-modified AC supports exhibited different reactivity and durability in batch and continuous-flow mode owing to the difference of interaction between Pd species and AC supports.

Green synthesis and characterization of palladium nanoparticles and its conjugates from solanum trilobatum leaf extract

An important area of research in nanotechnology deals with the synthesis of nanoparticles of different chemical compositions,sizes and controlled monodispersity.Currently,there is a growing need to develop environmentally benign nanoparticle synthesis in which no toxic chemicals are used in the synthesis protocol.Palladium nanoparticles(Pd Np) are of interest because of their catalytic properties and affinity for hydrogen.Our protocol for the phyto-synthesis of Pd Np under moderate p H and room temperature offers a new means to develop environmentally benign nanoparticles.Solanum trilobatum is enlightened in our present study as it is enriched with phytochemicals to reduce palladium chloride ions.Poly MVA a dietary supplement based on the nontoxic chemotherapeutic lipoic acid-palladium complex(LA-Pd) is been hypothesized as the new paradigm of cancer therapy.Hence forth we successfully conjugated lipoic acid(S-Pd Np-LA) and vitamins(S-Pd Np-Vitamin-LA) to palladium nanoparticles synthesised from Solanum trilobatum leaf extract.These nanoparticles(S-Pd Np,S-Pd Np-LA,S-Pd Np-Vitamin-LA) were characterized with UV-Vis Spectroscopy,SEM and FTIR analysis,which revealed that S-Pd Np are polydisperse and of different morphologies ranging from 60?70 nm(S-Pd Np),65?80 nm(S-Pd Np-LA) and 75?100 nm(S-Pd Np-Vitamin-LA) in size.

Heck Arylation of Acrylonitrile with Aryl Iodides Catalyzed by a Silica-bound Arsine Palladium(0) Complex

Acrylonitrile reacts with aryl iodides in the presence of tri-n-butylamine and a catalytic amount of a silica-bound arsine palladium(0) complex to afford stereoselectively (E)-cinnamo- nitriles in high yields.

Samarium(II) Diiodide Induced Polarity Inversion of π-Allyl Palladium Complexes: The Formation of Allylic Selenides

Allylic acetates were reduced with Pd(0)-SmI2 in the presence of ArSeBr to form corresponding allylic selenides in good yields.

Progress of Palladium Alloy Membranes in Hydrogen Energy

Palladium and palladium alloy membranes have attracted wide attention in hydrogen permeation areas for their excellent permeability, perm -selectivity and thermal stability. This paper review the principle of hydrogen permeation, type of alloys and the fabrication methods. At last, the progress and achievements on palladium alloy membranes by Northwest Institute for Non-Ferrous Metal Research are emphasized.

Palladium nanoparticles in cross-linked polyaniline as highly efficient catalysts for Suzuki-Miyaura reactions

Palladium nanoparticles supported on cross-linked polyaniline with bulky phosphorus ligands were developed.These catalysts showed high efficiency in the Suzuki-Miyaura reaction of aryl chlorides and bromides with phenylboronic acids.Aryl chlorides and bromides with functional groups,such as CN,MeO,CHO,MeCO and NO_2,were converted to the corresponding biphenyls in high yields with catalyst loading.Additionally,the catalysts combined high activity with good reusability;they could be used at least five times for the Suzuki-Miyaura coupling reaction.

Ionic palladium complex as an efficient and recyclable catalyst for the carbonylative Sonogashira reaction

The neutral palladium（Ⅱ） complex bis-[1-（5＇-diphenylphosphinothiazol-2＇-yl）-imidazolyl]dichloropalladium（Ⅱ）（1A） ligated by thiazolylimidazolyl-based phosphine（L1） in which thiazolylimidazolyl acted as an S- and N-donor provider with weak coordinating nature,and the ionic complex bis-[1-（5＇-diphenylphosphinothiazol-2＇-yl）-3-methylimidazolium]dichloropalladium（Ⅱ） trifluoromethanesulfonate（2A） ligated by thiazolylimidazolium-based phosphine（L2） after quaternization of L1 using methyl trifluoromethanesulphonate were synthesized.It was found that the introduced positive charges and strong electron-withdrawing effect in 2A not only led to changes in the configuration and structural stability of the complex,but also lowered its catalytic performance in carbonylative Sonogashira reactions.These effects reveal the important role of the N-donor in 1A.In addition,as an ionic palladium complex,2A combined with the room-temperature ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate could be recycled eight times as the catalyst in carbonylative Sonogashira reactions without detectable metal leaching.

Arylation of Allylic Alcohols with Aryl Iodides Catalyzed by a Silica-Bound Bidentate Sulfur Palladium (0) Complex

Allylic alcohols react with aryl iodides in the presence of tri-n-butylamine and a catalytic amount of a silica-bound bidentate sulfur palladium (0) complex to form 3-arylaldehydes or ketones in good yields.

A Comparative Assessment of Hydrogen Embrittlement: Palladium and Palladium-Silver (25 Weight% Silver) Subjected to Hydrogen Absorption/Desorption Cycling

The negative effects of hydrogen embrittlement on metallic systems have been investigated through determination of the mechanical properties of two metallic systems that were exposed to hydrogen. An assessment of the effects of hydrogen absorption/desorption cycling on the tensile strength, ductility, and microhardness of pure palladium and the alloy palladium-silver (25 weight% silver) has been undertaken. The variables that are the focus of the study are the amount of hydrogen absorbed by the metal, deuterium isotope effect, number of hydrogen absorption/desorption cycles, and the hydrogen exposure temperature. Under all conditions studied, the mechanical properties of pure palladium were significantly altered as a result of hydrogen exposure, with significant hydrogen embrittlement occurring. In contrast, the mechanical properties of the palladium-silver alloy showed little alteration as a result of hydrogen exposure, including virtually no occurrence of hydrogen embrittlement.

Preparation,Characterization and Catalytic Activity of Palladium Nanoparticles Embedded in the Mesoporous Silica Matrices

Novel in-situ reduction approach was applied for the synthesis of palladium nanoparticles in the pores of mesoporous silica materials with grafted siliconhydride groups. Matrices possessing different structural properties (MCM-41, SBA-15 and Silochrom) were used. Samples were studied by nitrogen adsorption-desorption method, low-angle X-ray diffraction, transmission electron microscopy (TEM) and FT-IR/PAS spectroscopy. The temperature-programmed oxidation (TPO) and reduction (TPR) methods were applied to examine reducibility of palladium species. Palladium containing catalysts were tested in methane oxidation reaction. It was demonstrated that relatively large pores in SBA-15 type silica facilitated formation of well-dispersed palladium nanoparticles confined in the pores channels. In the case of MCM-41 support, metallic palladium nanoparticles were formed on the external surface. The obtained materials showed high catalytic activity. Lower activity of the samples containing small crystallites located in the pore volume at high temperatures was related to worse accessibility of active sites to the reation mixture.

DISLOCATION DISSOCIATIONS AND FAULTENERGIES IN Ni_3Al ALLOYS DOPED WITH PALLADIUM

Dislocation structures in polycrystalline Ni 3Al alloy doped with palladium deformed at room temperature have been investigated by transmission electron microscopy. The structure consists mainly of dislocations dissociated into a /2〈011〉 super partials bounding an anti phase boundary (APB). Dislocations dissociated into a /3〈112〉 super Shockley partials bounding a superlattice intrinsic stacking fault (SISF) are also common debris. The majority of the SISFs are truncated loops, i.e. the partials bounding the SISF are of similar Burgers vector. These faulted loops are generated from APB coupled dislocations, according to a mechanism for formation of SISFs proposed by Suzuki et al , and recently modified by Chiba et al . The APB energies for {111} and {010} slip planes are measured to be 144±20 mJ/m 2 and 102±11 mJ/m 2 respectively, and the SISF energy has been estimated to be 12 mJ/m 2 in this alloy. It is concluded that the dislocation structure in Ni 74.5 Pd 2Al 23.5 alloy deformed at room temperature is similar to that in binary Ni 3Al, and the difference in fault energies between these two alloys is small. Thus, it seems unlikely that the enhancement of ductility of Ni 74.5 Pd 2Al 23.5 results from only such a small decrease of the ordering energy of the alloy. SISF bounding dislocations also have no apparent influence on the ductilization of Ni 74.5 Pd 2Al 23.5 alloy.

Shape-Controlled Synthesis of Palladium Nanoparticles and Their SPR/SERS Properties

Morphological evolution of Pd nanoparticles was studied in a solution-phase synthesis using cetyltrimethylammonium bromide （CTAB） and CTAB/sodium citrate mixture as capping agents, respectively. The morphological diversity of Pd nanoparticles is the combined effect of different Pd twinned seeds formed in the nucleation stage and selectively enlarging one set of crystallographic facets in the growth stage, both of which can be affected by the concentrations of CTAB. Through changing the concentrations of CTAB and sodium ascorbate, Pd nanoparticles with different shapes were obtained. When citrate ions were introduced to manipulate the nucleation and growth process, star-shaped icosahedra and nanorods with pentagram cross-sections were obtained. Pd nanoparticles with different shapes have quite different surface plasmon resonance and surface-enhanced Raman scattering properties.

Influence of CeO_2 and La_2O_3 on properties of palladium catalysts used for emission control of natural gas vehicles

Pd/YZ-Al2O3 （Y and Zr modified Al2O3, and hereafter, labelled as A1） catalysts with 4 wt% additive CeO2 and/or La2O3 were prepared and characterized by X-ray photoelectron spectroscopy （XPS）, NO-temperature programmed desorption （NO-TPD）, Nz-adsorption/desorption （Branauer-Emmet-Teller BET method）, X-ray diffraction （XRD） and CO-chemisorption. Catalytic activities for CH4, CO and NO conversion were tested in a gas mixture simulated the emissions from natural gas vehicles （NGVs） operated under stoichiometric conditions. The results indicated that all catalysts exhibited excellent catalytic performances for CH4 and CO oxidation and the promoting effect of CeO2 or La2O3 was significant for NO conversion. XPS results showed that the electron density around Pd was increased by CeO2 and/or La2O3, the binding energy of Pd 3d decreased as the order： Pd/Al 〉 Pd/Ce/Al 〉 Pd/La/Al 〉 Pd/CeLa/Al. The electron-rich Pd showed Rh-like catalytic properties which exhibited good activity for the reduction of NO. NO-TPD results showed that the addition of CeO2 and/or La2O3 increased NO adsorption on surface, and promoted the conversion of NO.

Determination of Nickel and Palladium in Environmental Samples by Low Temperature ETV-ICP-OES Coupled with Liquid-liquid Extraction with Dimethylglyoxime as Both Extractant and Chemical Modifier

A novel method for the determination of nickel and palladium in environmental samples by low temperature ETV-ICP-OES with dimethylglyoxime（DMG） as both the extractant and chemical modifier has been developed. In this study, it was found that nickel and palladium can form complexes with dimethylglyoxime（0. 05%, mass fraction） at pH 6.0 and can be extracted into chloroform quantitatively. The complexes can be evaporated into plasma at a suita-ble temperature（ 1400℃） for ICP-OES detection. Under the optimized conditions, the detection limits of nickel and palladium are 0.48 and 0. 40 ng/mL, respectively, while the RSD values are separately 5.0% and 3.1% （p = 50 ng/mL, n = 7）. The proposed method was applied to the determination of the target analytes in environmental sam-ples with satisfactory results.