Investigation of Microstructure and Phase Composition of Chromic Oxide, AZS/Cr and High-alumina Refractories after Exposure of Basalt and Aluminaboronsilicate Glasses Melts

The microstructure and phase composition of high-alumina,chromic oxide,and AZS/Cr refractories containing 30%and 60%(by mass)Cr_(2)O_(3) after exposure to aluminaboronsilicate glasses and basalt melts depending on the type of melts and temperature have been studied.The mechanisms of refractory corrosion by the used melts and the factors contributing to the inhibition of corrosion development have been investigated by the method of petrographic analysis.On the basis of obtained results,the use of high-alumina,chromic oxide,and AZS/Cr refractories in the sections of glass furnace linings,experiencing the intensive impact of aluminaboronsilicate glasses and basalt melts,has been confirmed and scientifically substantiated.

Effect of ZrC Modified Graphite on Structure and Properties of Low-carbon Al_(2)O_(3)-C Refractories

To address the issues of reduced performance and shortened lifespan during the low-carbonizating process of Al_(2)O_(3)-C refractories,nano-crystalline ZrC modified graphite was prepared using Zr powder and flake graphite as raw materials,with NaCl and NaF mixed salt serving as the medium.The flake graphite was gradually replaced by ZrC modified graphite in the preparation of Al_(2)O_(3)-C refractories,and its impact on the material’s structure and properties was investigated.The results indicate that,compared to samples with only flake graphite,the introduction of 1 mass%to 5 mass%nano-crystalline ZrC modified graphite can significantly enhance the mechanical performance of low-carbon Al_(2)O_(3)-C refractories.When 5 mass%ZrC modified graphite is added,the mechanical properties of the samples are optimal,with the cold modulus of rupture and elastic modulus reaching 22.5 MPa and 65.0 GPa,respectively.

The 9^(th) International Symposium on Refractories

Organizedby The Chinese Society for Metals The Chinese Ceramic Society Sinosteel Luoyang Institute of Refractories Research Co.,Ltd.Sponsored by Refractories Committee of The Chinese Society for Metals Sinosteel Luonai Materials Technology Corporation Co-Sponsoredby State Key Laboratory of Advanced Refractories The State Key Laboratory of Refractories and Metallurgy Refractories Press Indian Refractory Makers Association The Federation for International Refractory Research and Education.

Microwave-assisted Synthesis of Al_(4)SiC_(4) and Its Effect on Properties of MgO-C Refractories

Al_(4)SiC_(4) was synthesized from Al powder, silicon carbide, and graphite by microwave sintering, and characterized by XRD and SEM. Then the synthesized material was added to the magnesia carbon refractory brick to study its effect on the oxidation resistance, apparent porosity, bulk density, elastic modulus, and modulus of rupture. It is found that Al_(4)SiC_(4) can be synthesized by microwave sintering at 1 300 ℃ and the addition of Al_(4)SiC_(4)-containing material as an antioxidant can enhance the oxidation resistance of the magnesia carbon refractory brick.

Effects of Al_(2)O_(3)-SiO_(2) Raw Material Types on Properties of Anorthite Based Insulation Refractories

To optimize their Al_(2)O_(3)-SiO_(2) raw materials,anorthite based insulation refractories were prepared by the in-situ sintering process combined with the foaming method after sintering at 1350℃for 3 h,using green and pollution-free kaolin,kyanite,andalusite and sillimanite as Al_(2)O_(3)-SiO_(2) raw materials,respectively,and industrial CaCO_(3) as the CaO source.Effects of Al_(2)O_(3)-SiO_(2) raw material types on the physical properties,phase composition and microstructure were investigated.The results are as follows.All samples prepared by different Al_(2)O_(3)-SiO_(2) raw materials have hexagonal flake anorthite and a small amount of mullite and corundum.Their bulk density and thermal conductivity decrease in the order of using kaolin,andalusite,kyanite and sillimanite as the Al_(2)O_(3)-SiO_(2) raw material,but their apparent porosity increases.Moreover,in the sample with kaolin,the bonding between anorthite crystals on the pore walls is closer than that of the other samples,which is conducive to increasing the cold crushing strength.The bonding between anorthite crystals on pore walls gradually decreases in the order of using kyanite,andalusite and sillimanite as the Al_(2)O_(3)-SiO_(2) raw material,thus their cold crushing strength decreases accordingly.In comprehensive consideration,the properties of the sample from kyanite are the optimal.Its apparent porosity,thermal conductivity and cold crushing strength are 84.6%,0.141 W·m^(-1)·K^(-1) and 1.89 MPa,respectively.

Corrosion behavior of co-gasification slag of furfural residue and coal on alumina-silica refractories

Gasification of furfural residue with coal can realize its efficient and clean utilization.But the high alkali metal content in furfural slag is easy to cause the corrosion of gasifier refractory.Two gasification coals with different silica alumina ratio and a furfural residue were selected in the study.The effects of furfural residue additions on corrosion of silica brick,corundum brick,high alumina brick and mullite brick were investigated by using XRD,SEM-EDS and Factsage Software,and the corrosion mechanism was analyzed.With increasing furfural residue addition,the permeability of the slags to high-aluminium-bearing refractories first decreases and then increases,while the permeability on silica brick shows a slight decrease trend.Leucite(KAlSi_(2)O_(6))with high-melting temperature is generated from the reaction of K_(2)O and SiO_(2)in slag with Al_(2)O_(3)in refractories after furfural residue is added,which hinders the infiltration of slag in refractories.Kaliophilite(KAlSiO_(4))of low-melting point is formed when K_(2)O content increases,and this contributes to the infiltration of slag in refractories.The acid-base reaction between slag and silica brick is distinctly occurred,more slag reacts with SiO_(2)in the silicon brick,resulting in a decrease in the amount of slag infiltrating into the silicon brick as furfural residue is added.The corrosion of silica brick is mainly caused by the acid-base reaction,while the corrosion of three alumina based refractory bricks of corundum,mullite and high alumina brick is determined by slag infiltration.A linear correlation between the percolation rate and slag viscosity is established,the slag permeability increases with decreasing viscosity,resulting in stronger permeability for the high Si/Al ratio slag with lower viscosity.

Current Situation and Development of Refractories for Clean Steel Production

The low cost and high efficient clean steels metallur- gy has been focused much attention in China. Among the factors affecting the cleanliness and consequent quali- ty of steel products, refractories are one of the key fac- tors. Meanwhile the restriction of resource, energy and environment is getting stronger, thus the improvement of refractories becontes much more important. In this paper, refractories selection principle Jbr clean steel production according to their thermodynamic features was ex- plained; refractories for tundLsh and flow control in con- tinuous casting, which play important roles in prohibi- ring secondary contamination of molten steel, were intro- duced. Moreover, new development of low-carbon and carbon-free refractory materials was also described.

Chrome-free Basic Refractories for Burning Zone of Cement Rotary Kiln

Based on the relevant phase diagrams of ternary system in MgO - CaO - ZrO2 - SiO2 quarternary systems, the phase diagram of Fe - O system and the condensed phase stability area diagram of iron oxides, the corrosion resistance of MgO - CaO - ZrO2 refractories to silicate cement, and the forming conditions and prepar- ing measures of hercynite are analyzed.

The 4th International Exhibition on Refractories, Industrial Ceramics and Furnaces(RCF Expo'2003)Beijing, China, April 15-17, 2003In conjunction with China Refractories Seminar' 2003-Technology and Markets

Organizers and Sponsors: China Association of Refractories Industry The Chinese Society for Metals The Chinese Ceramic Society

Research on Refractories Technology to Meet the Demands of Steel-making Process

Based on the refractories research of Baosteel, the demands for refractories from the developing steel-making technology as high security, high efficiency, energy saving and environment .friendly are introduced.

Progress of Environment-friendly Basic Refractories for Cement Industry

The chrome pollution from cement industry was introduced briefly,the research on chrome free basic refractories for cement kilns was reviewed,the production technologies of magnesia calcia,magnesium aluminate spinel,magnesia hercynite refractories,etc. were specified,the principles to improve thermal shock resistance and coating adhesiveness of refractories were analyzed,the measures to extend service life by improving production equipment and service conditions of refractories were put forward,the future of chrome free refractories was expected and some developing suggestions were given.

Replacement of Flake Graphite in Aluminacarbon Refractories by Hexagonal Boron Nitride

Three kinds of composite alumina refractories were prepared with tabular alumina （3-1 and 1-0 mm） as aggregates,tabular alumina powder,α-Al2 O3 micropowder,and Si powder as matrix,adding 3 mass％ hexagonal boron nitride （h-BN）,3 mass％ flake graphite and 10 mass％ flake graphite,respectively.Cold physical properties,hot modulus of rupture,oxidation resistance,thermal shock resistance and slag corrosion resistance of the specimens were compared.The results show that：（1） physical properties and hot modulus of rupture of Al2 O3-h-BN refractories are slightly different from those of low carbon Al2 O3-C refractories,but better than those of traditional Al2 O3-C refractories with 10 mass％ graphite ; （2） Al2 O3-h-BN refractories have better thermal shock resistance and oxidation resistance than the carbon containing refractories,while similar slag resistance with low carbon Al2 O3-C refractories ; （3） h-BN can replace flake graphite as a starting material for the preparation of composite alumina refractories,considering the overall properties of the material.

Effect of Heat Treatment Temperature on Properties of Chinese Calcined Flint Clay Based Plastic Refractories

Effects of different heat treatment temperatures on properties of Chinese calcined flint clay based plastic refractories were investigated using Chinese calcined flint clay as starting material, aluminum sulfate and fireclay as binding system. The results showed that with temperature rising, Chinese calcined flint clay based plastic refractories shrinked firstly and then expanded. The modulus of rupture （MOR） and the cold crushing strength （CCS） inereased firstly and then decreased from 110 ℃ to 600 ℃ , then increased obviously. Thermal expansion coefficient increased from 110 ℃ to 760 ℃, decreased from 760 ℃ to 1 300 ℃ , and increased from 1 300 ℃ to1500 ℃.

Major Trends in Refractories Industry at the Beginning of the 21^(st) Century

An analysis of the present and of the future of the refractories industry is being presented , considering some important technical, economical, human and environmental issues , on a worldwide basis. Refractories are still neededas confinement materials to prevent heat and mass transferlosses in many diverse manufacturing industries , and will remain so , but the main challenges , this industry do needto meet, are to adjust to an overcapacity production , to cope with new needs of the customers , in particular the'outsourcing' , which is a new customer / supplier relationship being adopted by many of them, and to keep the research and development alive in a more and more competitive arena. Among the direct consequences , are the need to keep the education world in refractory engineering training alive and to cope with macro and micro projects to change the image of the Refractories , from a commodity material to a sophisticated 'high-tech' composite material . Some suggestions are provided in the text.

Recent Progress on Al_(2)O_(3)-C Refractories with Low/ultra-low Carbon Content:A Review

This work intends to provide a comprehensive review on the development of Al_(2)O_(3)-C refractories with low/ultra-low carbon content.It covers three parts:carbon materials,microstructure optimization of the refractory matrix by ceramic phases,and application of metal Al as raw material.Carbon black,expanded graphite,and ultrafine microcrystalline graphite,as price-competitive carbon materials,can be chosen to prepare the low-carbon Al_(2)O_(3)-C refractories after some special treatment.Ni/Co/Fe-catalyzed phenolic resin contributes to improving the properties of the low-carbon Al_(2)O_(3)-C refractories.The performance deterioration of the low-carbon Al_(2)O_(3)-C refractories can also be improved by in-situ formed or pre-synthesized ceramic phases.Metal Al,characterized by plasticity forming,acceleration of sintering,oxidation resistance,and high reactivity,can be used as raw materials to completely replace graphite,and the prepared resin bonded Al-Al_(2)O_(3)based refractories are one novel development direction of the ultra-low carbon Al_(2)O_(3)-C refractories.

Present Situation of Refractories for Baosteel

The paper reviews the present situation of refractories for Baosteel, including refractories for iron-making system, converters, ladles and tundishes. Descriptions have been also conducted on the environment protection and reutilization of refractories in Baosteel, together with some suggestions for refractories suppliers to meet the advancement in iron and steel making technology of Baosteel.

Influence of Ultra-Fine B_4C and Nano-SiO_2 on the Properties of Alumina-Graphite Refractories

The role of nano-SiO 2 and ultra-fine boron carbide on the properties of alumina-graphite materials was investigated. The study showed that the ultra-fine boron carbide added modified the microstructure of residual carbon and promoted the chemical bond between residual carbon from phenolic resin and flake graphite. The carbon white could strengthen the residual carbon from phenolic resin. These two additives improved the mechanical properties of AG refractories at both room temperature and high temperature, and thermal shock resistance was improved noticeably. When the two additives were doped together, carbon white could retard the evaporation of B 2O 3. Thermal shock resistance was guaranteed with a smaller amount of ultra-fine boron carbide.

Highlights of Recent Advances in Refractories for Iron and Steel Industry in China

Recently procured outstanding achievements in iron and steel industry in China are presented by data or facts in steel output, energy consumption, technical and economical indicators and advanced technologies that are being adopted. The latest achievements in refractonries for this biggest user industry are reviewed, covering new refractories for CDQ coke oven, BF hearth, AOD Lining, long life tundish, SEN for clean steel making and regenerative reheating furnace . The reciprocal relationship is obvious that the rapid development of iron and steel industry has given an impetus to the advance of refractories industry, which in return has contributed greatly to the former.

Some Aspects in the Development of High Performance Refractories for Iron and Steel Making in China

In the past 25 years in China, to meet with the rapid increase in steel production accompanied by adoption of advanced metallurgical technologies, there has been fast development of China＇ s refractories industry in production capacity, in quality improvement and in development of new products. Sophisticated high performance refractory materials mainly based on our rich reserves of magncsite, bauxite and flake graphite have been developed, such as carbon-bonded products, high purity oxide products, bauxite-based low creep and high strength high alumina bricks and LC, ULC and ZC castables. They have been used in blast furnaces, BOFs, EAFs, secondary refining and continuous casting with considerable improvement in service pecformance.

Comprehensive Utilization of Natural Magnesium-Containing Resources and the Development of MgO-Based Refractories

This paper presents the ways of comprehensive utilization of the natural magnesium containing resources and the trends of the MgO based refractories used in high temperature industries. In the first part, the uses and productions of metal Mg, sorel cement, Mg (OH) 2 fire retardant, light magnesium carbonate, light magnesia and magnesium sulphate are described. In the second part, the developments of MgO based refractories used in steelmaking process, nonferrous metallurgy, cement rotary kiln and waste melting furnace are described from some applied theories, including corrosion resistant and slaking resistant MgO CaO materials, chrome free bricks such as MgO CaO ZrO 2 , MgO MgO Al 2 O 3 , MgO MgO·Al 2 O 3 ZrO 2 , MgO MgO·Al 2 O 3 2MgO ·TiO 2 and MgO FeO·Al 2 O 3 , and MgO containing monolithic refractories etc.