Department of Civil Engineering, Universitas Katolik Parahyangan, Bandung, 40141, Indonesiaof loose sand with fungus

This article presents an innovative method of bio-mediated soil improvement for increasing the shear strength of loose sand.The improvement is realized by mixing the loose sand with the inoculum of Rhizopus oligosporus,a kind of fungus widely used in food industry for making Indonesian tempeh.The objective of this article is to investigate the performance and mechanism of mixing tempeh inoculum as a binding agent of loose sand particles.The inoculum dosage,water content of loose sand,and curing time were examined for identifying the increment of unconfined compressive strength(q_u)of the samples.The results showed that q_u of the treated samples increased when the inoculum dosage was elevated.It shows that 5.24%inoculum could yield 68 kPa of q_u,and 5%water content and 3 d curing time produced the maximum q_u.Moreover,the mechanism of hypha and mycelium in binding the soil particles was clearly observed using a digital microscope and scanning electron microscope.

Engineering behaviour of in situ cored deep cement mixed marine deposits subjected to undrained and drained shearing

The deep cement mixing(DCM)is used to improve the capacity and reduce the settlement of the soft ground by forming cemented clay columns.The investigation on the mechanical behaviour of the DCM samples is limited to either laboratory-prepared samples or in-situ samples under unconfined compression.In this study,a series of drained and undrained triaxial shearing tests was performed on the in-situ cored DCM samples with high cement content to assess their mechanical behaviours.It is found that the drainage condition affects significantly the stiffness,peak and residual strengths of the DCM samples,which is mainly due to the state of excess pore water pressure at different strain levels,i.e.being positive before the peak deviatoric stress and negative after the peak deviatoric stress,in the undrained tests.The slope of the failure envelope changes obviously with the confining pressures,being steeper at lower stress levels and flatter at higher stress levels.The strength parameters,effective cohesion and friction angle obtained from lower stress levels(c′0 andφ′0)are 400 kPa and 58°,respectively,which are deemed to be true for design in most DCM applications where the in-situ stress levels are normally at lower values of 50-200 kPa.Additionally,the computed tomography(CT)scanning system was adopted to visualize the internal structures of DCM samples.It is found that the clay pockets existing inside the DCM samples due to uneven mixing affect markedly their stress-strain behaviour,which is one of the main reasons for the high variability of the DCM samples.

Experimental Study on Engineering Behavior of Solidified Soil for Scour Repair and Protection

A new scour countermeasure using solidified slurry for offshore foundation has been proposed recently.Fluidized solidified slurry is pumped to seabed area around foundation for scour protection or pumped into the developed scour holes for scour repair as the fluidized material solidifies gradually.In the pumping operation and solidification,the engineering behaviors of solidified slurry require to be considered synthetically for the reliable application in scour repair and protection of ocean engineering such as the pumpability related flow value,flow diffusion behavior related rheological property,anti-scour performance related retention rate in solidification and bearing capacity related strength property after solidification.In this study,a series of laboratory tests are conducted to investigate the effects of mix proportion(initial water content and binder content)on the flow value,rheological properties,density,retention rate of solidified slurry and unconfined compressive strength(UCS).The results reveal that the flow value increases with the water content and decreases with the binder amount.All the solidified slurry exhibits Bingham plastic behavior when the shear rate is larger than 5 s^(-1).The Bingham model has been employed to fit the rheology test results,and empirical formulas for obtaining the density,yield stress and viscosity are established,providing scientific support for the numerical assessment of flow and diffusion of solidified slurry.Retention rate of solidified slurry decreases with the water flow velocity and flow value,which means the pumpability of solidified slurry is contrary to anti-scour performance.The unconfined compressive strength after solidification reduces as the water content increases and binder content decreases.A design and application procedure of solidified soil for scour repair and protection is also proposed for engineering reference.

Triaxial creep damage characteristics of sandstone under high crustal stress and its constitutive model for engineering application

The creep characteristics of rock under high crustal stress are of important influence on the long‐term stability of deep rock engineering.To study the creep characteristics and engineering application of sandstone under high crustal stress,this study constructed nonlinear creep damage(NCD)constitutive mode based on the triaxial graded loading‒unloading creep test of sandstone in the Yuezhishan Tunnel.A numerical NCD constitutive model and a breakable lining(BL)model were developed based on FLAC3D and then applied to the stability analysis of the Yuezhishan Tunnel.Based on the creep test results of sandstone,a power function of creep rate and stress level was constructed,by which the long‐term strength was solved.The results show that the long‐term strength of the red sandstone based on the related function of the steady‐state creep rate and stress level is close to the measured stress value in engineering.The NCD model considering damage factors reflects the instantaneous and viscoelastic plasticity deformation characteristics of the red sandstone.The numerical NCD constitutive model and the BL model can reflect surrounding rock deformation characteristics and lining failure characteristics in practical engineering.The research results provide theoretical references for long‐term stability analysis of rock engineering and the deformation control of surrounding rock under high crustal stress.

Introduction to the Special Issue on Soft Computing Techniques in Materials Science and Engineering

Soft computing(SC)refers to the ability of a digital computer or robot to perform functions that are normally associated with intelligent individuals,such as reasoning and problem-solving.An example of this would be a project aimed at creating systems capable of reasoning,discovering meaning,generalising,or learning from past experience.Science and engineering problems that are both non-linear and complex can be solved using these methodologies.It has been proven that these algorithms can be used to solve numerous real-world problems.The techniques outlined can be used to increase the accuracy of existing models/equations,or they can be used to propose a newmodel that can address the problem.

Extended wet sieving method for determination of complete particle size distribution of general soils

The traditional standard wet sieving method uses steel sieves with aperture?0.063 mm and can only determine the particle size distribution(PSD)of gravel and sand in general soil.This paper extends the traditional method and presents an extended wet sieving method.The extended method uses both the steel sieves and the nylon filter cloth sieves.The apertures of the cloth sieves are smaller than 0.063 mm and equal 0.048 mm,0.038 mm,0.014 mm,0.012 mm,0.0063 mm,0.004 mm,0.003 mm,0.002 mm,and 0.001 mm,respectively.The extended method uses five steps to separate the general soil into many material sub-groups of gravel,sand,silt and clay with known particle size ranges.The complete PSD of the general soil is then calculated from the dry masses of the individual material sub-groups.The extended method is demonstrated with a general soil of completely decomposed granite(CDG)in Hong Kong,China.The silt and clay materials with different particle size ranges are further examined,checked and verified using stereomicroscopic observation,physical and chemical property tests.The results further confirm the correctness of the extended wet sieving method.

Effect of eccentric and inclined loading on the bearing capacity of strip footing placed on rock mass

This paper deals with the bearing capacity determination of strip footing on a rock mass in hilly area by considering the influence of inclined and eccentric loading. Applying the generalized HoekBrown failure criterion, the failure behavior of the rock mass is modeled with the help of the power cone programming in the lower bound finite element limit analysis framework. Using bearing capacity factor(Ns), the change in bearing capacity of the strip footing due to the occurrence of eccentrically inclined loading is presented. The variations of the magnitude of Ns are obtained by examining the effects of the Hoek-Brown rock mass strength parameters(uniaxial compressive strength(sci), disturbance factor(D), rock parameter(mi), and Geological Strength Index(GSI)) in the presence of different magnitudes of eccentricity(e) and inclination angle(λ) with respect to the vertical plane, and presented as design charts. Both the inclined loading modes, i.e., inclination towards the center of strip footing(+λ) and inclination away from the center of strip footing(-λ), are adopted to perform the investigation. In addition, the correlation between the input parameters and the corresponding output is developed by utilizing the artificial neural network(ANN). Additionally, from sensitivity analysis, it is observed that inclination angle(λ) is the most sensitive parameter. For practicing engineers, the obtained design equation and design charts can be beneficial to understand the bearing capacity variation in the existence of eccentrically inclined loading in mountain areas.

Mapping the geography of editors-in-chief

Purpose:This study aims to explore the geography of editors-in-chief to demonstrate which countries exercise the highest-level decision-making in scholarly communication.In addition,the study seeks to investigate the potential relationships between the origin and nationality of academic publishers and the geography of editors-in-chief.Design/methodology/approach:The analysis involves 11,915 journals listed in Web of Science’s Social Sciences Citation Index(SSCI)and Science Citation Index Expanded(SCIE).These journals employ 15,795 scholars as editors-in-chief.The geographical locations of the institutions the editors-in-chief are affiliated with were identified;then,the data were aggregated at the country level.Findings:The results show that most editors-in-chief are located in countries of the Anglosphere,primarily the United States and the United Kingdom.In addition,most academic publishers and professional organizations that publish academic journals were found to be based in the United States and the United Kingdom,where most editors-in-chief are also based.Research limitations:The analysis involves journals indexed in the Web of Science’s SCIE/SSCI databases,which are demonstrably biased toward the English language.Furthermore,the study only takes a snapshot of the geography of editors-in-chief for the year 2022,but it does not investigate trends.Research implications:The study maps the highest-level decision-making in scholarly communication.Originality/value:The study explores and maps the geography of editors-in-chief by using a massive dataset.

Multi-scale analysis of carbon mineralization in lime-treated soils considering soil mineralogy

Mineral carbonation is emerging as a reliable CO_(2) capture technology that can mitigate climate change.In lime-treated clayey soils,mineral carbonation occurs through the carbonation of free lime and cementitious products derived from pozzolanic reactions.The kinetics of the reactions in lime-treated clayey soils are variable and depend primarily on soil mineralogy.The present study demonstrates the role of soil mineralogy in CO_(2) capture and the subsequent changes caused by carbon mineralization in terms of the unconfined compressive strength(UCS)of lime-treated soils during their service life.Three clayey soils(kaolin,bentonite,and silty clay)with different mineralogical characteristics were treated with 4%lime content,and the samples were cured in a controlled environment for 7 d,90 d,180 d,and 365 d.After the specified curing periods,the samples were exposed to CO_(2) in a carbonation cell for 7 d.The non-carbonated samples purged with N2 gas were used as a benchmark to compare the mechanical,chemical-mineralogical,and microstructure changes caused by carbonation reactions.Experimental investigations indicated that exposure to CO_(2) resulted in an average increase of 10%in the UCS of limetreated bentonite,whereas the strength of lime-treated kaolin and silty clay was reduced by an average of 35%.The chemical and microstructural analyses revealed that the precipitated carbonates effectively filled the macropores of the treated bentonite,compared to the inadequate cementation caused by pozzolanic reactions,resulting in strength enhancement.In contrast,strength loss in lime-treated kaolin and silty clay was attributed to the carbonation of cementitious phases and partly to the tensile stress induced by carbonate precipitation.In terms of carbon mineralization prospects,lime-treated kaolin exhibited maximum carbonation due to the higher availability of unreacted lime.The results suggest that,in addition to the increase in compressive strength,adequate calcium-bearing phases and macropores determine the efficiency of carbon mineralization in lime-treated clayey soils.

Coupled multiphysical model for investigation of influence factors in the application of microbially induced calcite precipitation

The study presents a comprehensive coupled thermo-bio-chemo-hydraulic(T-BCH)modeling framework for stabilizing soils using microbially induced calcite precipitation(MICP).The numerical model considers relevant multiphysics involved in MICP,such as bacterial ureolytic activities,biochemical reactions,multiphase and multicomponent transport,and alteration of the porosity and permeability.The model incorporates multiphysical coupling effects through well-established constitutive relations that connect parameters and variables from different physical fields.It was implemented in the open-source finite element code OpenGeoSys(OGS),and a semi-staggered solution strategy was designed to solve the couplings,allowing for flexible model settings.Therefore,the developed model can be easily adapted to simulate MICP applications in different scenarios.The numerical model was employed to analyze the effect of various factors,including temperature,injection strategies,and application scales.Besides,a TBCH modeling study was conducted on the laboratory-scale domain to analyze the effects of temperature on urease activity and precipitated calcium carbonate.To understand the scale dependency of MICP treatment,a large-scale heterogeneous domain was subjected to variable biochemical injection strategies.The simulations conducted at the field-scale guided the selection of an injection strategy to achieve the desired type and amount of precipitation.Additionally,the study emphasized the potential of numerical models as reliable tools for optimizing future developments in field-scale MICP treatment.The present study demonstrates the potential of this numerical framework for designing and optimizing the MICP applications in laboratory-,prototype-,and field-scale scenarios.

Impact of spatially varying rock disturbance on rock slope stability

Degradation of rock mass produced by rock blasting,stress relief,and other causes is an important factor in the assessment of rock strength.Quantified as a disturbance factor,such degradation varies depending on blasting control,stress state and stress relief,and rock mass quality.This study focuses on the impact of disturbance on the safety of slopes.The disturbance in the rock mass is characterized by the geometry of the disturbed zone,its size,the magnitude,and the decaying rate with the distance away from the slope surface.A method accounting for decay of rock disturbance is presented.A study of the impact of rock disturbance characteristics on the quantitative stability measures of slopes was carried out.These characteristics included disturbed zone geometry,its thickness,the maximum magnitude of the disturbance factor,and the rate of disturbance decaying.The thickness of the disturbed zone and the maximum factor of disturbance were found to have the greatest impact.For example,the factor of safety for a 45slope in low-quality rock mass can decrease from 1.96 to 1.09 as the thickness of the disturbed zone increases from 1/4 of slope height H to the double of H and the maximum disturbance factor increases from 0.5 to 1.Uniform thickness of a disturbed zone was found to yield more conservative outcomes than the triangular zones did.The critical failure surfaces were found to be shallow for high rates of disturbance decay,and they were the deepest for spatially uniform disturbance factors.

Numerical manifold method for thermo-mechanical coupling simulation of fractured rock mass

As a calculation method based on the Galerkin variation,the numerical manifold method(NMM)adopts a double covering system,which can easily deal with discontinuous deformation problems and has a high calculation accuracy.Aiming at the thermo-mechanical(TM)coupling problem of fractured rock masses,this study uses the NMM to simulate the processes of crack initiation and propagation in a rock mass under the influence of temperature field,deduces related system equations,and proposes a penalty function method to deal with boundary conditions.Numerical examples are employed to confirm the effectiveness and high accuracy of this method.By the thermal stress analysis of a thick-walled cylinder(TWC),the simulation of cracking in the TWC under heating and cooling conditions,and the simulation of thermal cracking of the SwedishÄspöPillar Stability Experiment(APSE)rock column,the thermal stress,and TM coupling are obtained.The numerical simulation results are in good agreement with the test data and other numerical results,thus verifying the effectiveness of the NMM in dealing with thermal stress and crack propagation problems of fractured rock masses.

Numerical analysis of moving train induced vibrations on tunnel,surrounding ground and structure

This study is focused on the effect of vibration induced by moving trains in tunnels on the surrounding ground and structures.A three-dimensional finite element model is established for a one-track railway tunnel and an adjacent twelve-storey building frame by using commercial software Midas GTS-NX(2019)and Midas Gen.This study considered the moving load effect of a complete train,which varies with space as well as with time.The effect of factors such as train speed,overburden pressure on the tunnel and variation in soil properties are studied in the time domain.As a result,the variations in horizontal and vertical acceleration for two different sites,i.e.,the free ground surface(without structure)and the area containing the structure,are compared.Also,the displacement pattern of the raft foundation is plotted for different train velocities.At lower speeds,the heaving phenomenon is negligible,but as the speed increases,both the heaving and differential settlement increase in the foundation.This study demonstrates that the effect of moving train vibrations should be considered in the design of new nearby structures and proper ground improvement should be considered for existing structures.

Computer vision-aided DEM study on the compaction characteristics of graded subgrade filler considering realistic coarse particle shapes

The compaction quality of subgrade filler strongly affects subgrade settlement.The main objective of this research is to analyze the macro-and micro-mechanical compaction characteristics of subgrade filler based on the real shape of coarse particles.First,an improved Viola-Jones algorithm is employed to establish a digitalized 2D particle database for coarse particle shape evaluation and discrete modeling purposes of subgrade filler.Shape indexes of 2D subgrade filler are then computed and statistically analyzed.Finally,numerical simulations are performed to quantitatively investigate the effects of the aspect ratio(AR)and interparticle friction coefficient(μ)on the macro-and micro-mechanical compaction characteristics of subgrade filler based on the discrete element method(DEM).The results show that with the increasing AR,the coarse particles are narrower,leading to the increasing movement of fine particles during compaction,which indicates that it is difficult for slender coarse particles to inhibit the migration of fine particles.Moreover,the average displacement of particles is strongly influenced by the AR,indicating that their occlusion under power relies on particle shapes.The dis-placement and velocity of fine particles are much greater than those of the coarse particles,which shows that compaction is primarily a migration of fine particles.Under the cyclic load,the interparticle friction coefficientμhas little effect on the internal structure of the sample;under the quasi-static loads,however,the increase inμwill lead to a significant increase in the porosity of the sample.This study could not only provide a novel approach to investigate the compaction mechanism but also establish a new theoretical basis for the evaluation of intelligent subgrade compaction.

Reinforcing effects of polypropylene on energy absorption and fracturing of cement-based tailings backfill under impact loading

Polypropylene(PP)fiber-reinforced cement-based tailings backfill(FRCTB)is a green compound material with superior crack resistance and has good prospects for application in underground mining.However,FRCTB exhibits susceptibility to dynamic events,such as impact ground pressure and blast vibrations.This paper investigates the energy and crack distribution behavior of FRCTB under dynamic impact,considering the height/diameter(H/D)effect.Split Hopkinson pressure bar,industrial computed tomography scan,and scanning electron microscopy(SEM)experiments were carried out on six types of FRCTB.Laboratory outcomes confirmed fiber aggregation at the bottom of specimens.When H/D was less than 0.8,the proportion of PP fibers distributed along theθangle direction of80°-90°increased.For the total energy,all samples presented similar energy absorption,reflectance,and transmittance.However,a rise in H/D may cause a rise in the energy absorption rate of FRCTB during the peak phase.A positive correlation existed between the average strain rate and absorbed energy per unit volume.The increase in H/D resulted in a decreased crack volume fraction of FRCTB.When the H/D was greater than or equal to 0.7,the maximum crack volume fraction of FRCTB was observed close to the incidence plane.Radial cracks were present only in the FRCTB with an H/D ratio of 0.5.Samples with H/D ratios of 0.5 and 0.6 showed similar distributions of weakly and heavily damaged areas.PP fibers can limit the emergence and expansion of cracks by influencing their path.SEM observations revealed considerable differences in the bonding strengths between fibers and the FRCTB.Fibers that adhered particularly well to the substrate were attracted together with the hydration products adhering to surfaces.These results show that FRCTB is promising as a sustainable and green backfill for determining the design properties of mining with backfill.

Liquefaction susceptibility and deformation characteristics of saturated coral sandy soils subjected to cyclic loadings-a critical review

Coral sandy soils widely exist in coral island reefs and seashores in tropical and subtropical regions.Due to the unique marine depositional environment of coral sandy soils,the engineering characteristics and responses of these soils subjected to monotonic and cyclic loadings have been a subject of intense interest among the geotechnical and earthquake engineering communities.This paper critically reviews the progress of experimental investigations on the undrained behavior of coral sandy soils under monotonic and cyclic loadings over the last three decades.The focus of coverage includes the contractive-dilative behavior,the pattern of excess pore-water pressure(EPWP)generation and the liquefaction mechanism and liquefaction resistance,the small-strain shear modulus and strain-dependent shear modulus and damping,the cyclic softening feature,and the anisotropic characteristics of undrained responses of saturated coral sandy soils.In particular,the advances made in the past decades are reviewed from the following aspects:(1)the characterization of factors that impact the mechanism and patterns of EPWP build-up;(2)the identification of liquefaction triggering in terms of the apparent viscosity and the average flow coefficient;(3)the establishment of the invariable form of strain-based,stress-based,or energy-based EPWP ratio formulas and the unique relationship between the new proxy of liquefaction resistance and the number of cycles required to reach liquefaction;(4)the establishment of the invariable form of the predictive formulas of small strain modulus and strain-dependent shear modulus;and(5)the investigation on the effects of stress-induced anisotropy on liquefaction susceptibility and dynamic deformation characteristics.Insights gained through the critical review of these advances in the past decades offer a perspective for future research to further resolve the fundamental issues concerning the liquefaction mechanism and responses of coral sandy sites subjected to cyclic loadings associated with seismic events in marine environments.

Experimental and numerical settlement analysis of railway track over geogrid reinforced ballast

Purpose-The main objective of the present research is to investigate the benefits of using geogrid reinforcement in minimizing the rate of deterioration of ballasted rail track geometry resting on soft clay and to explore the effect of load amplitude,load frequency,presence of geogrid layer in ballast layer and ballast layer thickness on the behavior of track system.These variables are studied both experimentally and numerically.This paper examines the effect of geogrid reinforced ballast laying on a layer of clayey soil as a subgrade layer,where a half full scale railway tests are conducted as well as a theoretical analysis is performed.Design/methodologylapproach-The experimental tests work consists of laboratory model tests to investigate the reduction in the compressibility and stress distribution induced in soft clay under a ballast railway reinforced by geogrid reinforcement subjected to dynamic load.Experimental model based on an approximate half scale for general rail track engineering practice is adopted in this study which is used in Iraqi railways.The investigated parameters are load amplitude,load frequency and presence of geogrid reinforcement layer.A half fuli-scale railway was constructed for carrying out the tests,which consists of two rails 800 mm in iength with three w00den sleepers(900 mm×90 mm×90 mm).The ballast was overlying 500 mm thick clay layer.The tests were carried out with and without geogrid reinforcement,the tests were carried out in a well tied steel box of 1.5 m length X 1 m width X 1 m height.A series of laboratory tests were conducted to investigate the response of the ballast and the clay layers where the ballast was reinforced by a geogrid.Settlement in ballast and clay,was measured in reinforced and unreinforced ballast cases.In addition to the laboratory tests,the application of numerical analysis was made by using the finite element program PLAXIS 3D 2013.Findings-It was concluded that the settlement increased with increasing the simulated train load amplitude,there is a sharp increase in settlement up to the cycle 500 and after that,there is a gradual increase to level out between,2,500 and 4,500 cycles depending on the load frequency.There is a little increase in the induced settlement when the load amplitude increased from 0.5 to i ton,but it is higher when the load amplitude increased to 2 ton,the increase in settlement depends on the geogrid existence and the other studied parameters.Both experimental and numerical results showed the same behavior.The effect of load frequency on the settlement ratio is almost constant after 500 cycles.In general,for reinforced cases,the effect of load frequency on the settlement ratio is very small ranging between 0.5 and 2%compared with the unreinforcedcase.Originalitylvalue-Increasing the ballast layer thickness from 20 cm to 30 cm leads to decrease the settlement by about 50%.This ascertains the efficiency of ballast in spreading the waves induced by the track.

Elastic-viscoplastic behaviors of polymer-blend geocell sheets:Numerical and experimental investigations

Polymer-blend geocell sheets(PBGS)have been developed as substitute materials for manufacturing geocells.Various attempts have been made to test and predict the behaviors of commonly used geogrids,geotextiles,geomembranes,and geocells.However,the elastic-viscoplastic behaviors of novel-developed geocell sheets are still poorly understood.Therefore,this paper investigates the elastic-viscoplastic behaviors of PBGS to gain a comprehensive understanding of their mechanical properties.Furthermore,the tensile load-strain history under various loading conditions is simulated by numerical calculation for widespread utilization.To achieve this goal,monotonic loading tests,short-term creep and stress relaxation tests,and multi-load-path tests(also known as arbitrary loading history tests)are performed using a universal testing machine.The results are simulated using the nonlinear three-component(NLTC)model,which consists of three nonlinear components,i.e.a hypo-elastic component,a nonlinear inviscid component,and a nonlinear viscid component.The experimental and numerical results demonstrate that PBGS exhibit significant elastic-viscoplastic behavior that can be accurately predicted by the NLTC model.Moreover,the tensile strain rates significantly influence the tensile load,with higher strain rates resulting in increased tensile loads and more linear load-strain curves.Also,parametric analysis of the rheological characteristics reveals that the initial tensile strain rates have negligible impact on the results.The rate-sensitivity coefficient of PBGS is approximately 0.163,which falls within the typical range observed in most geosynthetics.

Contributions of Engineering Geological Properties of Subgrade Soils to Premature Failure of Major Highways in Southwestern Nigeria:A Case Study of Akure-Ikere Ekiti Highway

Geotechnical analyses were carried out to examine the contributions of engineering geological properties of subgrade soils to the failure of the Akure-Ikere Ekiti road,Southwestern Nigeria.Field observations revealed that the road is in a very poor state of serious deformation and disrepair as most parts of the road alignment have failed.The alignment of the studied road is predominantly underlain by Granite,Charnockites,and Migmatites.Laboratory tests results showed that the natural moisture content ranges from 10.98 to 21.4%,liquid limit from 22.8 to 47.7%,plastic limit from 19.2 to 24.6,plasticity index 3.6 to 26.3%.The grain size analysis revealed that the amount of fines ranges from 15.9 to 49%.Others are linear shrinkage,between 1.4 and 10%,free swell between 25 and 46%,maximum dry density from 1593 to 2016 kg/m,and CBR between 5 and 48%.The specific gravity ranges from 2.64 to 2.74.With reference to AASHTO classification,5% of the samples was classified as A-4,15% classified as A-2-4,40% classified as A-6,while 40% classified as A-7-6.The dominance of fair-to-good California bearing ratio,fair to good maximum dry density,high linear shrinkage and A-7-6,A-6,and A-2-4 soil groups have combined to give fair-to-good geotechnical properties to the studied soils.Generally,the fair to good geotechnical properties of soil of the road under study is an indication that the contribution of subgrade soil to the failure of the highway is negligible.The total breakdown of the road can be traced to substandard engineering specifications which are complemented by a poor drainage system.

Inter-comparison of field snow measurements using different instruments in Türkiye

Snow is important in Türkiye especially in the mountainous eastern areas where it may stay on the ground for more than half of the year.This region plays a vital role in feeding the water resources of the trans-boundary Euphrates-Tigris Basin,supporting crucial dams for water supply,irrigation and energy production.Thus,easy,frequent,correct and economical ways of measuring the snowpack is crucial.The snow properties at specific locations in the mountainous eastern regions over the two snow seasons(2018 and 2019)were studied by using different instruments and techniques,snow pit(box/cylinder/wedge cutter types),snow tube(Federal Sampler)and SnoTel(Snowpack Analyzer).The results point out a 1.7%-7.1%variation between different cutter type snow density measurements within snow pit analysis and the long-term utilized snow tube observations show a closer relation to box/cylinder type cutters.As for the continuous SnoTel observations,a variation of 2.4%-9.8%with various cutter types and a 5.9%difference regarding the snow tube density results are detected.These findings indicate a close range among different instruments,but it is the best when all three systems complement each other to characterize the snowpack effectively in the complex terrain since each has its own advantages.