Double glow plasma surface metallurgy technique was used to fabricate a Fe?Al?Cr?Nb alloyed layer onto the surface of the 45 steel. The microstructures and composition of th?eA Fl?eCr?Nb alloyed layer were analyzed by...Double glow plasma surface metallurgy technique was used to fabricate a Fe?Al?Cr?Nb alloyed layer onto the surface of the 45 steel. The microstructures and composition of th?eA Fl?eCr?Nb alloyed layer were analyzed by scanning electronic microscopy, X-ray diffraction and energy dispersive spectroscopy. The results indicate thatthe 20 μm alloyed layer is homogeneous and compact. The alloyed elements exhibit a gradient distribution along the cross section. Microhardness and nanoindentation tests imply that the surface hardness of the alloyed layer reaches HV 580, which is almost 2.8 times that of the substrate. Compared with the substrate, the alloyed layer has a much smaller displacement and a larger elastic modulus. According to the friction and wear tests at room temperature, the? FeAl?Cr?Nb alloyed layer has lower friction coefficient and less wear mass, implying that the Fe?Al?Cr?Nb alloyed layer can effectively improve the surface hardness and wear resistance of the substrate.展开更多
To obtain the stable temperature field required for growing sapphire crystals, the influence of relative positions between RF coil and crucible on the performances of sapphires produced by edge-defined film-fed growth...To obtain the stable temperature field required for growing sapphire crystals, the influence of relative positions between RF coil and crucible on the performances of sapphires produced by edge-defined film-fed growth（EFG） technique was investigated. For comparison, the crucible was located at the top（case A） and the middle（case B） of the RF coil, respectively. Furthermore, the lattice integrities were studied by the double-crystal X-ray diffraction, and the dislocations were observed under the optical microscope and atomic force microscope after corroding in molten KOH at 390 ℃. The crystals in case B exhibit better lattice integrity with smaller full width at half maximum of 29.13 rad·s, while the value in case A is 45.17 rad·s. The morphologies of dislocation etch pits in both cases show typical triangular symmetry with smooth surfaces. However, the dislocation density of 2.8×104 cm-2 in case B is only half of that in case A, and the distribution is more uniform, compared to the U-shaper in case A.展开更多
Sapphire, belonging to hexagonal crystal system, is typically anisotropic which makes it direction-sensitive. To research the effects of growth directions on properties of sapphire, c-[0001] seed（c-sapphire） and a-[...Sapphire, belonging to hexagonal crystal system, is typically anisotropic which makes it direction-sensitive. To research the effects of growth directions on properties of sapphire, c-[0001] seed（c-sapphire） and a-[11-20] seed（a-sapphire） were used to prepare sapphire by edge-defined film-fed growth（EFG） method. The samples were analyzed through lattice integrity, dislocation and corrosion performance by double-crystal XRD, OM, AFM, SEM and EDX. It was shown that the lattice integrities of two growth-direction crystals were both well due to the small FWHM values. While the average densities of dislocation in c-sapphire and a-sapphire were 9.2×103 and 3.9×103 cm-2 respectively, the energy of dislocation in c-sapphire was lower than that in a-sapphire. During Strong Phosphoric Acid（SPA） etching, the surface of c-sapphire basically kept smooth but in a-sapphire there were many point-like corrosion pits where aluminum and oxygen atoms lost by 2：1. Our work means that it will be promising for growing c-[0001] seed sapphire by EFG if aided by parameter optimization.展开更多
基金Project(51371097)supported by the National Natural Science Foundation of ChinaProject supported by the Priority Academic Program Development of Jiangsu Higher Education Institutions,China
文摘Double glow plasma surface metallurgy technique was used to fabricate a Fe?Al?Cr?Nb alloyed layer onto the surface of the 45 steel. The microstructures and composition of th?eA Fl?eCr?Nb alloyed layer were analyzed by scanning electronic microscopy, X-ray diffraction and energy dispersive spectroscopy. The results indicate thatthe 20 μm alloyed layer is homogeneous and compact. The alloyed elements exhibit a gradient distribution along the cross section. Microhardness and nanoindentation tests imply that the surface hardness of the alloyed layer reaches HV 580, which is almost 2.8 times that of the substrate. Compared with the substrate, the alloyed layer has a much smaller displacement and a larger elastic modulus. According to the friction and wear tests at room temperature, the? FeAl?Cr?Nb alloyed layer has lower friction coefficient and less wear mass, implying that the Fe?Al?Cr?Nb alloyed layer can effectively improve the surface hardness and wear resistance of the substrate.
基金Project(BA2012049)supported by the Special Fund of Jiangsu Province for the Transformation of Scientific and Technological Achievements,China
文摘To obtain the stable temperature field required for growing sapphire crystals, the influence of relative positions between RF coil and crucible on the performances of sapphires produced by edge-defined film-fed growth（EFG） technique was investigated. For comparison, the crucible was located at the top（case A） and the middle（case B） of the RF coil, respectively. Furthermore, the lattice integrities were studied by the double-crystal X-ray diffraction, and the dislocations were observed under the optical microscope and atomic force microscope after corroding in molten KOH at 390 ℃. The crystals in case B exhibit better lattice integrity with smaller full width at half maximum of 29.13 rad·s, while the value in case A is 45.17 rad·s. The morphologies of dislocation etch pits in both cases show typical triangular symmetry with smooth surfaces. However, the dislocation density of 2.8×104 cm-2 in case B is only half of that in case A, and the distribution is more uniform, compared to the U-shaper in case A.
基金Funded by the Special Fund of Jiangsu Province for the Transformation of Scientific and Technological Achievements(No.BA2012049)the Priority Academic Program Development of Jiangsu Higher Education Institutions
文摘Sapphire, belonging to hexagonal crystal system, is typically anisotropic which makes it direction-sensitive. To research the effects of growth directions on properties of sapphire, c-[0001] seed（c-sapphire） and a-[11-20] seed（a-sapphire） were used to prepare sapphire by edge-defined film-fed growth（EFG） method. The samples were analyzed through lattice integrity, dislocation and corrosion performance by double-crystal XRD, OM, AFM, SEM and EDX. It was shown that the lattice integrities of two growth-direction crystals were both well due to the small FWHM values. While the average densities of dislocation in c-sapphire and a-sapphire were 9.2×103 and 3.9×103 cm-2 respectively, the energy of dislocation in c-sapphire was lower than that in a-sapphire. During Strong Phosphoric Acid（SPA） etching, the surface of c-sapphire basically kept smooth but in a-sapphire there were many point-like corrosion pits where aluminum and oxygen atoms lost by 2：1. Our work means that it will be promising for growing c-[0001] seed sapphire by EFG if aided by parameter optimization.
