利用数值模拟方法模拟了在喷射成形Al Fe V Si系耐热铝合金过程中雾化液滴的飞行状态及凝固行为 ,给出了不同尺寸雾化液滴的冷却速度和固相分数随飞行距离的变化规律 ,并对雾化颗粒的形貌组织进行了观察分析。在雾化颗粒中观察到了尺寸...利用数值模拟方法模拟了在喷射成形Al Fe V Si系耐热铝合金过程中雾化液滴的飞行状态及凝固行为 ,给出了不同尺寸雾化液滴的冷却速度和固相分数随飞行距离的变化规律 ,并对雾化颗粒的形貌组织进行了观察分析。在雾化颗粒中观察到了尺寸在 1～ 10 μm的第二相 ,能谱及XRD分析表明这种第二相为Al12 (Fe ,V) 3展开更多
The effect of quenching rate on the electrical conductivity and microstructure of thick plates of incumbent AA7050 was investigated by employing Jominy end quench test. The electrical conductivity measurement and micr...The effect of quenching rate on the electrical conductivity and microstructure of thick plates of incumbent AA7050 was investigated by employing Jominy end quench test. The electrical conductivity measurement and microstructural observation were conducted at different distances from the quenched end. The results indicate that the average cooling rates decrease with increasing the distance from the quenched end of the bar in the quench sensitive temperature range. However, the electrical conductivity increases with the increase of distance from the quenched end. The surface parts of the plate were fully recrystallized, while partial recrystallization took place at the quarter and center parts of the plate. The quench induced grain boundary precipitates became remarkably coarser and discontinuously distributed with increasing distance from the quenched end of the bar. Plenty of heterogeneous precipitates were observed to nucleate on A13Zr dispersoids when the distance from the quenched end was greater than 38mm.展开更多
文摘采用喷射成形方法制备了不同成分的Al Fe V Si耐热铝合金 ,对喷射成形工艺参数进行了优化 ,对沉积坯件的热挤压工艺进行了探索 ,对材料的组织进行了分析 ,并对不同成分材料的性能进行了比较。结果表明 :当喷射成形工艺参数选择合理时 ,沉积坯件具有良好的成形性与致密度 ,在随后的热挤压过程中 ,通过较低的挤压比即可使材料达到全致密 ;沉积坯件热挤压温度的降低有利于使材料获得更高的力学性能 ;同时 ,通过对合金成分的优化 ,可以获得加工和使用性能更加优良的Al Fe V
基金Project (50904010) supported by the National Natural Science Foundation of ChinaProject (2010DFB50340) supported by the China International Science and Technology Cooperation
文摘The effect of quenching rate on the electrical conductivity and microstructure of thick plates of incumbent AA7050 was investigated by employing Jominy end quench test. The electrical conductivity measurement and microstructural observation were conducted at different distances from the quenched end. The results indicate that the average cooling rates decrease with increasing the distance from the quenched end of the bar in the quench sensitive temperature range. However, the electrical conductivity increases with the increase of distance from the quenched end. The surface parts of the plate were fully recrystallized, while partial recrystallization took place at the quarter and center parts of the plate. The quench induced grain boundary precipitates became remarkably coarser and discontinuously distributed with increasing distance from the quenched end of the bar. Plenty of heterogeneous precipitates were observed to nucleate on A13Zr dispersoids when the distance from the quenched end was greater than 38mm.
