In this work, ultrathin pure HfO_2 and Al-doped HfO_2films（about 4-nm thick） are prepared by atomic layer deposition and the crystallinities of these films before and after annealing at temperatures ranging from 550...In this work, ultrathin pure HfO_2 and Al-doped HfO_2films（about 4-nm thick） are prepared by atomic layer deposition and the crystallinities of these films before and after annealing at temperatures ranging from 550℃ to 750℃ are analyzed by grazing incidence x-ray diffraction. The as-deposited pure HfO_2 and Al-doped HfO_2 films are both amorphous. After550-℃ annealing, a multiphase consisting of a few orthorhombic, monoclinic and tetragonal phases can be observed in the pure HfO_2 film while the Al-doped HfO_2 film remains amorphous. After annealing at 650℃ and above, a great number of HfO_2 tetragonal phases, a high-temperature phase with higher dielectric constant, can be stabilized in the Al-doped HfO_2 film. As a result, the dielectric constant is enhanced up to about 35. The physical mechanism of the phase transition behavior is discussed from the viewpoint of thermodynamics and kinetics.展开更多
Strained-Si0.73Ge0.27 channels are successfully integrated with high-R/metal gates in p-type metai-oxide- semi- conductor field effect transistors （pMOSFETs） using the replacement post-gate process. A silicon cap an...Strained-Si0.73Ge0.27 channels are successfully integrated with high-R/metal gates in p-type metai-oxide- semi- conductor field effect transistors （pMOSFETs） using the replacement post-gate process. A silicon cap and oxide inter layers are inserted between Si0.73Ge0.27 and high-κ dielectric to improve the interface. The fab- ricated Si0.73Ge0.27 pMOSFETs with gate length of 3Onto exhibit good performance with high drive current （~428μA/μm at VDD = 1 V） and suppressed short-channel effects （DIBL^77mV/V and SS^90mV/decade）. It is found that the enhancement of effective hole mobility is up to 200% in long-gate-length Si0.73Ge0.27-channel pMOSFETs compared with the corresponding silicon transistors. The improvement of device performance is reduced due to strain relaxation as the gate length decreases, while 26% increase of the drive current is still obtained for 30-nm-gate-length Si0.73Ge0.27 devices.展开更多
In the process of high-k films fabrication, a novel multi deposition multi annealing （MDMA） technique is introduced to replace simple post deposition annealing. The leakage current decreases with the increase of the...In the process of high-k films fabrication, a novel multi deposition multi annealing （MDMA） technique is introduced to replace simple post deposition annealing. The leakage current decreases with the increase of the post deposition annealing （PDA） times. The equivalent oxide thickness （EOT） decreases when the annealing time（s） change from 1 to 2. Furthermore, the characteristics of SILC （stress-induced leakage current） for an ultra-thin SiO2/HfO2 gate dielectric stack are studied systematically. The increase of the PDA time（s） from 1 to 2 can decrease the defect and defect generation rate in the HK layer. However, increasing the PDA times to 4 and 7 may introduce too much oxygen, therefore the type of oxygen vacancy changes.展开更多
The thickness effect of the TiN capping layer on the time dependent dielectric breakdown（TDDB） characteristic of ultra-thin EOT high-k metal gate NMOSFET is investigated in this paper.Based on experimental results,i...The thickness effect of the TiN capping layer on the time dependent dielectric breakdown（TDDB） characteristic of ultra-thin EOT high-k metal gate NMOSFET is investigated in this paper.Based on experimental results,it is found that the device with a thicker TiN layer has a more promising reliability characteristic than that with a thinner TiN layer.From the charge pumping measurement and secondary ion mass spectroscopy（SIMS） analysis,it is indicated that the sample with the thicker TiN layer introduces more Cl passivation at the IL/Si interface and exhibits a lower interface trap density.In addition,the influences of interface and bulk trap density ratio Nit/Not are studied by TDDB simulations through combining percolation theory and the kinetic Monte Carlo（kMC） method.The lifetime reduction and Weibull slope lowering are explained by interface trap effects for TiN capping layers with different thicknesses.展开更多
The positive bias temperature instability（PBTI） degradations of high-k/metal gate（HK/MG） n MOSFETs with thin TiN capping layers（1.4 nm and 2.4 nm） are systemically investigated. In this paper, the trap energy di...The positive bias temperature instability（PBTI） degradations of high-k/metal gate（HK/MG） n MOSFETs with thin TiN capping layers（1.4 nm and 2.4 nm） are systemically investigated. In this paper, the trap energy distribution in gate stack during PBTI stress is extracted by using ramped recovery stress, and the temperature dependences of PBTI（90℃,125℃, 160℃） are studied and activation energy（Ea） values（0.13 eV and 0.15 eV） are extracted. Although the equivalent oxide thickness（EOT） values of two TiN thickness values are almost similar（0.85 nm and 0.87 nm）, the 2.4-nm TiN one（thicker Ti N capping layer） shows better PBTI reliability（13.41% at 0.9 V, 90℃, 1000 s）. This is due to the better interfacial layer/high-k（IL/HK） interface, and HK bulk states exhibited through extracting activation energy and trap energy distribution in the high-k layer.展开更多
A multi-deposition multi-annealing technique （MDMA） is introduced into the process of high-k/metal gate MOSFET for the gate last process to effectively reduce the gate leakage and improve the device＇s performance. ...A multi-deposition multi-annealing technique （MDMA） is introduced into the process of high-k/metal gate MOSFET for the gate last process to effectively reduce the gate leakage and improve the device＇s performance. In this paper, we systematically investigate the electrical parameters and the time-dependent dielectric breakdown （TDDB） characteristics of positive channel metal oxide semiconductor （PMOS） under different MDMA process conditions, including the depo- sition/annealing （D＆A） cycles, the D＆A time, and the total annealing time. The results show that the increases of the number of D＆A cycles （from 1 to 2） and D＆A time （from 15 s to 30 s） can contribute to the results that the gate leakage current decreases by about one order of magnitude and that the time to fail （TTF） at 63.2% increases by about several times. However, too many D＆A cycles （such as 4 cycles） make the equivalent oxide thickness （EOT） increase by about 1A and the TTF of PMOS worsen. Moreover, different D＆A times and numbers of D＆A cycles induce different breakdown mechanisms.展开更多
A promising technology named epitaxy on nano-scale freestanding fin （ENFF） is firstly proposed for hetero- epitaxy. This technology can effectively release total strain energy and then can reduce the probability of ...A promising technology named epitaxy on nano-scale freestanding fin （ENFF） is firstly proposed for hetero- epitaxy. This technology can effectively release total strain energy and then can reduce the probability of gener- ating mismatch dislocations. Based on the calculation, dislocation defects can be eliminated completely when the thickness of the Si freestanding fin is less than 10nm for the epitaxial Ge layer. In addition, this proposed ENFF process can provide sufficient uniaxial stress for the epitaxy layer, which can be the major stressor for the SiGe or Ge channel fin field-effect transistor or nanowire at the 10nm node and beyond. According to the results of technology computer-aided design simulation, nanowires integrated with ENFF show excellent electrical perfor- mance for uniaxial stress and band offset. The ENFF process is compatible with the state of the art mainstream technology, which has a good potential for future applications.展开更多
Sub-20 nm node bulk FinFET PMOS devices with an all-last high-k/metal gate （HK/MG） process are fabricated and the influence of a series of device parameters on the device scaling is investigated. The high and thin F...Sub-20 nm node bulk FinFET PMOS devices with an all-last high-k/metal gate （HK/MG） process are fabricated and the influence of a series of device parameters on the device scaling is investigated. The high and thin Fin structure with a tapered sidewall shows better performance than the normal Fin structure. The punch through stop layer （PTSL） and source drain extension （SDE） doping profiles are carefully optimized. The device without SDE annealing shows a larger drive current than that with SDE annealing due to better Si crystal regrowth in the amorphous Fin structure after source/drain implantation. The band-edged MG has a better short channel effect immunity, but the lower effective work function （EWF） MG shows a larger driveability. A tradeoff choice for different EWF MGs should be carefully designed for the device＇s scaling.展开更多
： We introduced a TaN/TiAl/top-TiN triple-layer to modulate the effective work function of a TiN-based metal gate stack by varying the TaN thickness and top-TiN technology process. The results show that a thinner TaN...： We introduced a TaN/TiAl/top-TiN triple-layer to modulate the effective work function of a TiN-based metal gate stack by varying the TaN thickness and top-TiN technology process. The results show that a thinner TaN and PVD-process top-TiN capping provide smaller effective work function （EWF）, and a thicker TaN and ALD-process top-TiN capping provides a larger EWF; here, the EWF shifts are from 4.25 to 4.56 eV. A physical understanding of the dependence of the EWF on the top-TiN technology process and TaN thickness is proposed. Compared with PVD-TiN room temperature process, the ALD-TiN 400 ℃ process provides more thermal budget. It would also promote more Al atoms to diffuse into the top-TiN rather than the bottom-TiN. Meanwhile, the thicker TaN prevents the Al atoms diffusing into the bottom-TiN. These facts induce the EWF to increase.展开更多
基金Project supported by the National High Technology Research and Development Program of China(Grant No.2015AA016501)the National Natural Science Foundation of China(Grant Nos.61574168 and 61504163)
文摘In this work, ultrathin pure HfO_2 and Al-doped HfO_2films（about 4-nm thick） are prepared by atomic layer deposition and the crystallinities of these films before and after annealing at temperatures ranging from 550℃ to 750℃ are analyzed by grazing incidence x-ray diffraction. The as-deposited pure HfO_2 and Al-doped HfO_2 films are both amorphous. After550-℃ annealing, a multiphase consisting of a few orthorhombic, monoclinic and tetragonal phases can be observed in the pure HfO_2 film while the Al-doped HfO_2 film remains amorphous. After annealing at 650℃ and above, a great number of HfO_2 tetragonal phases, a high-temperature phase with higher dielectric constant, can be stabilized in the Al-doped HfO_2 film. As a result, the dielectric constant is enhanced up to about 35. The physical mechanism of the phase transition behavior is discussed from the viewpoint of thermodynamics and kinetics.
基金Supported by the National Basic Research Program of China under Grant No 2011CBA00605the National Natural Science Foundation of China under Grant No 61404165
文摘Strained-Si0.73Ge0.27 channels are successfully integrated with high-R/metal gates in p-type metai-oxide- semi- conductor field effect transistors （pMOSFETs） using the replacement post-gate process. A silicon cap and oxide inter layers are inserted between Si0.73Ge0.27 and high-κ dielectric to improve the interface. The fab- ricated Si0.73Ge0.27 pMOSFETs with gate length of 3Onto exhibit good performance with high drive current （~428μA/μm at VDD = 1 V） and suppressed short-channel effects （DIBL^77mV/V and SS^90mV/decade）. It is found that the enhancement of effective hole mobility is up to 200% in long-gate-length Si0.73Ge0.27-channel pMOSFETs compared with the corresponding silicon transistors. The improvement of device performance is reduced due to strain relaxation as the gate length decreases, while 26% increase of the drive current is still obtained for 30-nm-gate-length Si0.73Ge0.27 devices.
基金supported by the National High Technology Research and Development Program of China(Grant No.2015AA016501)the National Natural Science Foundation of China(Grant No.61306129)
文摘In the process of high-k films fabrication, a novel multi deposition multi annealing （MDMA） technique is introduced to replace simple post deposition annealing. The leakage current decreases with the increase of the post deposition annealing （PDA） times. The equivalent oxide thickness （EOT） decreases when the annealing time（s） change from 1 to 2. Furthermore, the characteristics of SILC （stress-induced leakage current） for an ultra-thin SiO2/HfO2 gate dielectric stack are studied systematically. The increase of the PDA time（s） from 1 to 2 can decrease the defect and defect generation rate in the HK layer. However, increasing the PDA times to 4 and 7 may introduce too much oxygen, therefore the type of oxygen vacancy changes.
基金supported by the National High Technology Research and Development Program of China(Grant No.SS2015AA010601)the National Natural Science Foundation of China(Grant Nos.61176091 and 61306129)the Opening Project of Key Laboratory of Microelectronics Devices&Integrated Technology,Institute of Micro Electronics of Chinese Academy of Sciences
文摘The thickness effect of the TiN capping layer on the time dependent dielectric breakdown（TDDB） characteristic of ultra-thin EOT high-k metal gate NMOSFET is investigated in this paper.Based on experimental results,it is found that the device with a thicker TiN layer has a more promising reliability characteristic than that with a thinner TiN layer.From the charge pumping measurement and secondary ion mass spectroscopy（SIMS） analysis,it is indicated that the sample with the thicker TiN layer introduces more Cl passivation at the IL/Si interface and exhibits a lower interface trap density.In addition,the influences of interface and bulk trap density ratio Nit/Not are studied by TDDB simulations through combining percolation theory and the kinetic Monte Carlo（kMC） method.The lifetime reduction and Weibull slope lowering are explained by interface trap effects for TiN capping layers with different thicknesses.
基金Project supported by the National High Technology Research and Development Program of China(Grant No.SS2015AA010601)the National Natural Science Foundation of China(Grant Nos.61176091 and 61306129)
文摘The positive bias temperature instability（PBTI） degradations of high-k/metal gate（HK/MG） n MOSFETs with thin TiN capping layers（1.4 nm and 2.4 nm） are systemically investigated. In this paper, the trap energy distribution in gate stack during PBTI stress is extracted by using ramped recovery stress, and the temperature dependences of PBTI（90℃,125℃, 160℃） are studied and activation energy（Ea） values（0.13 eV and 0.15 eV） are extracted. Although the equivalent oxide thickness（EOT） values of two TiN thickness values are almost similar（0.85 nm and 0.87 nm）, the 2.4-nm TiN one（thicker Ti N capping layer） shows better PBTI reliability（13.41% at 0.9 V, 90℃, 1000 s）. This is due to the better interfacial layer/high-k（IL/HK） interface, and HK bulk states exhibited through extracting activation energy and trap energy distribution in the high-k layer.
基金supported by the National High Technology Research and Development Program of China(Grant No.SS2015AA010601)the National Natural Science Foundation of China(Grant Nos.61176091 and 61306129)
文摘A multi-deposition multi-annealing technique （MDMA） is introduced into the process of high-k/metal gate MOSFET for the gate last process to effectively reduce the gate leakage and improve the device＇s performance. In this paper, we systematically investigate the electrical parameters and the time-dependent dielectric breakdown （TDDB） characteristics of positive channel metal oxide semiconductor （PMOS） under different MDMA process conditions, including the depo- sition/annealing （D＆A） cycles, the D＆A time, and the total annealing time. The results show that the increases of the number of D＆A cycles （from 1 to 2） and D＆A time （from 15 s to 30 s） can contribute to the results that the gate leakage current decreases by about one order of magnitude and that the time to fail （TTF） at 63.2% increases by about several times. However, too many D＆A cycles （such as 4 cycles） make the equivalent oxide thickness （EOT） increase by about 1A and the TTF of PMOS worsen. Moreover, different D＆A times and numbers of D＆A cycles induce different breakdown mechanisms.
基金Supported by the National Key Research and Development Program of China(2016YFA0301701)the Youth Innovation Promotion Association of CAS under Grant No 2016112
文摘A promising technology named epitaxy on nano-scale freestanding fin （ENFF） is firstly proposed for hetero- epitaxy. This technology can effectively release total strain energy and then can reduce the probability of gener- ating mismatch dislocations. Based on the calculation, dislocation defects can be eliminated completely when the thickness of the Si freestanding fin is less than 10nm for the epitaxial Ge layer. In addition, this proposed ENFF process can provide sufficient uniaxial stress for the epitaxy layer, which can be the major stressor for the SiGe or Ge channel fin field-effect transistor or nanowire at the 10nm node and beyond. According to the results of technology computer-aided design simulation, nanowires integrated with ENFF show excellent electrical perfor- mance for uniaxial stress and band offset. The ENFF process is compatible with the state of the art mainstream technology, which has a good potential for future applications.
基金supported by the National 02 IC Projectsthe Opening Project of Key Laboratory of Microelectronics Devices & Integrated Technology,Institute of Microelectronics,Chinese Academy of Sciences
文摘Sub-20 nm node bulk FinFET PMOS devices with an all-last high-k/metal gate （HK/MG） process are fabricated and the influence of a series of device parameters on the device scaling is investigated. The high and thin Fin structure with a tapered sidewall shows better performance than the normal Fin structure. The punch through stop layer （PTSL） and source drain extension （SDE） doping profiles are carefully optimized. The device without SDE annealing shows a larger drive current than that with SDE annealing due to better Si crystal regrowth in the amorphous Fin structure after source/drain implantation. The band-edged MG has a better short channel effect immunity, but the lower effective work function （EWF） MG shows a larger driveability. A tradeoff choice for different EWF MGs should be carefully designed for the device＇s scaling.
基金Project supported by the Important National Science&Technology Specific Projects(No.2009ZX02035)the National Natural Science Foundation of China(Nos.61176091,61306129)
文摘： We introduced a TaN/TiAl/top-TiN triple-layer to modulate the effective work function of a TiN-based metal gate stack by varying the TaN thickness and top-TiN technology process. The results show that a thinner TaN and PVD-process top-TiN capping provide smaller effective work function （EWF）, and a thicker TaN and ALD-process top-TiN capping provides a larger EWF; here, the EWF shifts are from 4.25 to 4.56 eV. A physical understanding of the dependence of the EWF on the top-TiN technology process and TaN thickness is proposed. Compared with PVD-TiN room temperature process, the ALD-TiN 400 ℃ process provides more thermal budget. It would also promote more Al atoms to diffuse into the top-TiN rather than the bottom-TiN. Meanwhile, the thicker TaN prevents the Al atoms diffusing into the bottom-TiN. These facts induce the EWF to increase.
