The effects of the deformation temperature and the strain rate on the hot deformation behavior of pure copper were investigated based on compression tests. The expressions of strain hardening rate, dynamic recrystalli...The effects of the deformation temperature and the strain rate on the hot deformation behavior of pure copper were investigated based on compression tests. The expressions of strain hardening rate, dynamic recrystallization critical stress, saturated stress, dynamic recovery volume fraction and dynamic recrystallization volume fraction were determined. According to the processing map, the instability regions occur in regions of 400?450 °C, 0.001?0.05 s?1 and 450?750 °C, 0.05?1 s?1. The deformation mechanism in the stability region is dynamic recrystallization. The flow stress was predicted. The results also show that the true stress–true strain curves predicted by the extracted model are in good agreement with the experimental results.展开更多
Machined chips of Mg-Zn-Y-Zr alloy were consolidated by cold pressing and then hot extrusion under various processing temperatures and extrusion ratios. The results show that the microstructure of the chip-extruded al...Machined chips of Mg-Zn-Y-Zr alloy were consolidated by cold pressing and then hot extrusion under various processing temperatures and extrusion ratios. The results show that the microstructure of the chip-extruded alloy is marked by a large number of recrystallized grains and some unrecrystallized grains, which results in high strength but low ductility at temperatures below 320 ℃. With increasing processing temperature up to 360 ℃, entirely recrystallized and equiaxed grains are obtained. Mg-Zn-Y-Zr alloy with low strength but high ductility is obtained compared with the alloy processed at low temperature. At 420℃, coarse and equiaxed grains are formed, which results in the drastic decrease of mechanical properties. With increasing extrusion ratio from 8 to 16, the grain refinement is more obvious and the mechanical properties at room temperature are improved effectively. However, the yield strength and ultimate tensile strength are improved a little with further increasing extrusion ratio.展开更多
基金Project(cstc2015jcyj BX0115)supported by the Chongqing Research Program of Basic Research and Frontier Technology,China
文摘The effects of the deformation temperature and the strain rate on the hot deformation behavior of pure copper were investigated based on compression tests. The expressions of strain hardening rate, dynamic recrystallization critical stress, saturated stress, dynamic recovery volume fraction and dynamic recrystallization volume fraction were determined. According to the processing map, the instability regions occur in regions of 400?450 °C, 0.001?0.05 s?1 and 450?750 °C, 0.05?1 s?1. The deformation mechanism in the stability region is dynamic recrystallization. The flow stress was predicted. The results also show that the true stress–true strain curves predicted by the extracted model are in good agreement with the experimental results.
基金Project (51005217) supported by the National Natural Science Foundation of ChinaProject (20100480677) supported by China Postdoctoral Science Foundation
文摘Machined chips of Mg-Zn-Y-Zr alloy were consolidated by cold pressing and then hot extrusion under various processing temperatures and extrusion ratios. The results show that the microstructure of the chip-extruded alloy is marked by a large number of recrystallized grains and some unrecrystallized grains, which results in high strength but low ductility at temperatures below 320 ℃. With increasing processing temperature up to 360 ℃, entirely recrystallized and equiaxed grains are obtained. Mg-Zn-Y-Zr alloy with low strength but high ductility is obtained compared with the alloy processed at low temperature. At 420℃, coarse and equiaxed grains are formed, which results in the drastic decrease of mechanical properties. With increasing extrusion ratio from 8 to 16, the grain refinement is more obvious and the mechanical properties at room temperature are improved effectively. However, the yield strength and ultimate tensile strength are improved a little with further increasing extrusion ratio.
