Platy potassium magnesium titanate (K0.8Mg0.4Ti1.6O4, KMTO) was synthesized by a flux method. The potential application of KMTO in removing copper ions from water pollutants was investigated. The crystal phases of spe...Platy potassium magnesium titanate (K0.8Mg0.4Ti1.6O4, KMTO) was synthesized by a flux method. The potential application of KMTO in removing copper ions from water pollutants was investigated. The crystal phases of specimens were identified by XRD. The morphology and structural information were characterized by SEM and TEM. The adsorption behavior under different conditions was investigated, including different pH values and different initial copper ion concentrations. The results show that the maximum adsorption capacity of Cu(II) ions is 290.697 mg/g, and almost 99.9% of Cu(II) ions can be removed, which is much higher than that of other sorbents reported. The kinetics of KMTO for the adsorption of Cu(II)ions was studied and the best fit can be obtained by the pseudo-second-order model. Adsorption isothermal data can be well interpreted by the Freundlich equation (R2=0.991). In conclusion, this study highlights that KMTO is a potential material for the efficient removal of heavy metal ions in polluted water. It also opens up a new opportunity for the applications of platy KMTO.展开更多
通过光固化的方法制备以磷灰石玻璃陶瓷和气相二氧化硅为无机填料的牙科复合树脂。采用扫描电镜/能谱仪(SEM/EDS)对复合材料的微观形貌进行分析,测量复合材料的三点抗弯强度。采用体外模拟体液(Simulated body fluid,SBF)浸泡法测试材...通过光固化的方法制备以磷灰石玻璃陶瓷和气相二氧化硅为无机填料的牙科复合树脂。采用扫描电镜/能谱仪(SEM/EDS)对复合材料的微观形貌进行分析,测量复合材料的三点抗弯强度。采用体外模拟体液(Simulated body fluid,SBF)浸泡法测试材料的生物活性。研究结果表明:材料的抗弯强度达到(137±10)MPa,能够满足牙齿修复的力学性能要求;材料在SBF中浸泡3d后,在表面形成矿化的碳酸磷灰石晶体层,表明材料具有较强的生物活性,可加快该材料植入人体后与骨的结合,并有利于龋齿的修复愈合。展开更多
In order to study the influence of rubidium(Rb)addition on the phase composition,microstructure,mechanical properties and cell response of bioactive glass-ceramics,CaO−SiO2−Na2O−B2O3−MgO−ZnO−P2O5 glass system was desi...In order to study the influence of rubidium(Rb)addition on the phase composition,microstructure,mechanical properties and cell response of bioactive glass-ceramics,CaO−SiO2−Na2O−B2O3−MgO−ZnO−P2O5 glass system was designed with and without addition of Rb.The results show that hydroxyapatite(HA)and Mg−whitelockite(Ca18Mg2H2(PO4)14)crystalline phases are formed in the glass matrix without Rb.After the addition of Rb,only HA phase is detected.The grain size of the crystals in the glass-ceramics is larger with the addition of Rb than that of samples without Rb.Rb addition can improve the bending strength of glass-ceramics.The cultivation of human bone marrow mesenchymal stem cells(hBMSCs)on Rb-containing glass-ceramics demonstrates enhanced cell adhesion,proliferation and ALP activity.In conclusion,Rb-modified glass-ceramics exhibit good mechanical property,excellent bioactivity and biocompatibility,which have potential for bone regeneration application.展开更多
In order to investigate the real-time cracking behavior of each component of a composite with strong interfacial bonding among lamellae, Ti-18 Nb(at.%) composite was prepared by spark plasma sintering(SPS), followed b...In order to investigate the real-time cracking behavior of each component of a composite with strong interfacial bonding among lamellae, Ti-18 Nb(at.%) composite was prepared by spark plasma sintering(SPS), followed by hot-rolling, annealing, and quenching. The microstructure and mechanical properties were characterized by scanning electron microscopy(SEM), energy dispersive spectroscopy(EDS), micro-region X-ray diffractometry(MRXRD), nanoindentation, and in-situ scanning electron microscopy tensile testing. The results show that the Ti-18 Nb consists of Ti-enriched, diffusion and Nb-enriched zones, and the sharp Nb gradient across different zones leads to inhomogeneous distribution of phase and mechanical properties. A remarkable finding is that the diffusion zones not only enable the cooperative deformation between the brittle Ti-enriched zones and the ductile Nb-enriched zones but also act as the crack-arresters to prevent the local cracks in the Ti-enriched zones from further propagating across the composite.展开更多
Tricalcium silicate cement(TSC)has been widely used in dental materials because of its self-setting behavior,good bioactivity,biocompatibility,osteoinductivity,and antibacterial effect.Tricalcium silicate(C3S)powder w...Tricalcium silicate cement(TSC)has been widely used in dental materials because of its self-setting behavior,good bioactivity,biocompatibility,osteoinductivity,and antibacterial effect.Tricalcium silicate(C3S)powder was prepared by Pechini technique with a calcining temperature of 1300℃ for 3 h.The influence of liquid/powder(L/P)rate on the setting time and the mechanical property of TSC was studied.Characterization methods including XRD,FTIR,SEM-EDS,TEM,and ICP-AES were utilized to study the properties of C3S powder and its hydrated cement.The bioactivity and biocompatibility of the cement were investigated by soaking test and cell culture,respectively.The results show that the L/P rate plays an important role in the setting time and the compressive strength of TSC.The surface of TSC was covered by hydroxyapatite deposition during the immersion experiment and the cells attachment on the surface of TSC was well,which indicated that TSC has good bioactivity and biocompatibility.In addition,TSC has excellent antibacterial properties against Staphylococcus aureus.In conclusion,TSC is a promising candidate for root canal filling materials.展开更多
The main goal of this work is to explore the possibility of using Au-modified hydroxyapatite(HA) as a potential sensor material. Tube-like HA structure was fabricated with the aid of a Nafion N-117 cation exchange mem...The main goal of this work is to explore the possibility of using Au-modified hydroxyapatite(HA) as a potential sensor material. Tube-like HA structure was fabricated with the aid of a Nafion N-117 cation exchange membrane and gold(Au) nanoparticles were added by a hydrothermal method. The morphology, structure and composition were characterized by scanning electron microscopy(SEM), transmission electron microscopy(TEM), X-ray diffraction(XRD), and X-ray photoelectron spectroscopy(XPS). The gas sensing properties were also investigated. Results show that Au nanoparticles are dispersed into the HA powder, which is tube-like, with rough inner and outer surfaces. Compared with pure HA, Au-modified HA exhibits improved sensing properties for NH_3. 5%(mass fraction) Au-modified HA shows the highest response with relatively short response/recovery time. The response is up to 79.2% when the corresponding sensor is exposed to 200×10^(-6) NH_3 at room temperature, and the response time and recovery time are 20 s and 25 s, respectively. For lower concentration, like 50×10^(-6), the response is still up to 70.8%. Good selectivity and repeatability are also observed. The sensing mechanism of high response and selectivity for NH_3 gas was also discussed. These results suggest that Au-HA composite is a promising material for NH_3 sensors operating at room temperature.展开更多
基金Project(51272289)supported by the National Natural Science Foundation of ChinaProject(51021063)supported by the Creative Research Group of National Science Foundation of China
文摘Platy potassium magnesium titanate (K0.8Mg0.4Ti1.6O4, KMTO) was synthesized by a flux method. The potential application of KMTO in removing copper ions from water pollutants was investigated. The crystal phases of specimens were identified by XRD. The morphology and structural information were characterized by SEM and TEM. The adsorption behavior under different conditions was investigated, including different pH values and different initial copper ion concentrations. The results show that the maximum adsorption capacity of Cu(II) ions is 290.697 mg/g, and almost 99.9% of Cu(II) ions can be removed, which is much higher than that of other sorbents reported. The kinetics of KMTO for the adsorption of Cu(II)ions was studied and the best fit can be obtained by the pseudo-second-order model. Adsorption isothermal data can be well interpreted by the Freundlich equation (R2=0.991). In conclusion, this study highlights that KMTO is a potential material for the efficient removal of heavy metal ions in polluted water. It also opens up a new opportunity for the applications of platy KMTO.
文摘通过光固化的方法制备以磷灰石玻璃陶瓷和气相二氧化硅为无机填料的牙科复合树脂。采用扫描电镜/能谱仪(SEM/EDS)对复合材料的微观形貌进行分析,测量复合材料的三点抗弯强度。采用体外模拟体液(Simulated body fluid,SBF)浸泡法测试材料的生物活性。研究结果表明:材料的抗弯强度达到(137±10)MPa,能够满足牙齿修复的力学性能要求;材料在SBF中浸泡3d后,在表面形成矿化的碳酸磷灰石晶体层,表明材料具有较强的生物活性,可加快该材料植入人体后与骨的结合,并有利于龋齿的修复愈合。
基金The authors are grateful for the financial supports from the Natural Science Foundation of Hunan Province,China(2019JJ50797)the Postdoctoral Science Foundation of China(2019T120711).
文摘In order to study the influence of rubidium(Rb)addition on the phase composition,microstructure,mechanical properties and cell response of bioactive glass-ceramics,CaO−SiO2−Na2O−B2O3−MgO−ZnO−P2O5 glass system was designed with and without addition of Rb.The results show that hydroxyapatite(HA)and Mg−whitelockite(Ca18Mg2H2(PO4)14)crystalline phases are formed in the glass matrix without Rb.After the addition of Rb,only HA phase is detected.The grain size of the crystals in the glass-ceramics is larger with the addition of Rb than that of samples without Rb.Rb addition can improve the bending strength of glass-ceramics.The cultivation of human bone marrow mesenchymal stem cells(hBMSCs)on Rb-containing glass-ceramics demonstrates enhanced cell adhesion,proliferation and ALP activity.In conclusion,Rb-modified glass-ceramics exhibit good mechanical property,excellent bioactivity and biocompatibility,which have potential for bone regeneration application.
基金Project(51625404)supported by the National Natural Science Foundation for Distinguished Young Scholar of ChinaProjects(51604104,51504295)supported by the National Natural Science Foundation of China
文摘In order to investigate the real-time cracking behavior of each component of a composite with strong interfacial bonding among lamellae, Ti-18 Nb(at.%) composite was prepared by spark plasma sintering(SPS), followed by hot-rolling, annealing, and quenching. The microstructure and mechanical properties were characterized by scanning electron microscopy(SEM), energy dispersive spectroscopy(EDS), micro-region X-ray diffractometry(MRXRD), nanoindentation, and in-situ scanning electron microscopy tensile testing. The results show that the Ti-18 Nb consists of Ti-enriched, diffusion and Nb-enriched zones, and the sharp Nb gradient across different zones leads to inhomogeneous distribution of phase and mechanical properties. A remarkable finding is that the diffusion zones not only enable the cooperative deformation between the brittle Ti-enriched zones and the ductile Nb-enriched zones but also act as the crack-arresters to prevent the local cracks in the Ti-enriched zones from further propagating across the composite.
基金Project(2019JJ50797)supported by Hunan Provincial Natural Science Foundation of China。
文摘Tricalcium silicate cement(TSC)has been widely used in dental materials because of its self-setting behavior,good bioactivity,biocompatibility,osteoinductivity,and antibacterial effect.Tricalcium silicate(C3S)powder was prepared by Pechini technique with a calcining temperature of 1300℃ for 3 h.The influence of liquid/powder(L/P)rate on the setting time and the mechanical property of TSC was studied.Characterization methods including XRD,FTIR,SEM-EDS,TEM,and ICP-AES were utilized to study the properties of C3S powder and its hydrated cement.The bioactivity and biocompatibility of the cement were investigated by soaking test and cell culture,respectively.The results show that the L/P rate plays an important role in the setting time and the compressive strength of TSC.The surface of TSC was covered by hydroxyapatite deposition during the immersion experiment and the cells attachment on the surface of TSC was well,which indicated that TSC has good bioactivity and biocompatibility.In addition,TSC has excellent antibacterial properties against Staphylococcus aureus.In conclusion,TSC is a promising candidate for root canal filling materials.
基金Project(51272289) supported by the National Natural Science Foundation of China
文摘The main goal of this work is to explore the possibility of using Au-modified hydroxyapatite(HA) as a potential sensor material. Tube-like HA structure was fabricated with the aid of a Nafion N-117 cation exchange membrane and gold(Au) nanoparticles were added by a hydrothermal method. The morphology, structure and composition were characterized by scanning electron microscopy(SEM), transmission electron microscopy(TEM), X-ray diffraction(XRD), and X-ray photoelectron spectroscopy(XPS). The gas sensing properties were also investigated. Results show that Au nanoparticles are dispersed into the HA powder, which is tube-like, with rough inner and outer surfaces. Compared with pure HA, Au-modified HA exhibits improved sensing properties for NH_3. 5%(mass fraction) Au-modified HA shows the highest response with relatively short response/recovery time. The response is up to 79.2% when the corresponding sensor is exposed to 200×10^(-6) NH_3 at room temperature, and the response time and recovery time are 20 s and 25 s, respectively. For lower concentration, like 50×10^(-6), the response is still up to 70.8%. Good selectivity and repeatability are also observed. The sensing mechanism of high response and selectivity for NH_3 gas was also discussed. These results suggest that Au-HA composite is a promising material for NH_3 sensors operating at room temperature.
