Toward understanding the microstructure characteristics,phase selection and magnetic properties of laser additive manufactured Nd-Fe-B permanent magnets

Nd-Fe-B permanent magnets play a crucial role in energy conversion and electronic devices.The essential magnetic properties of Nd-Fe-B magnets,particularly coercivity and remanent magnetization,are significantly infuenced by the phase characteristics and microstructure.In this work,Nd-Fe-B magnets were manufactured using vacuum induction melting(VIM),laser directed energy deposition(LDED)and laser powder bed fusion(LPBF)technologies.Themicrostructure evolution and phase selection of Nd-Fe-B magnets were then clarified in detail.The results indicated that the solidification velocity(V)and cooling rate(R)are key factors in the phase selection.In terms of the VIM-casting Nd-Fe-B magnet,a large volume fraction of theα-Fe soft magnetic phase(39.7 vol.%)and Nd2Fe17Bxmetastable phase(34.7 vol.%)areformed due to the low R(2.3×10-1?C s-1),whereas only a minor fraction of the Nd2Fe14B hard magnetic phase(5.15 vol.%)is presented.For the LDED-processed Nd-Fe-B deposit,although the Nd2Fe14B hard magnetic phase also had a low value(3.4 vol.%)as the values of V(<10-2m s-1)and R(5.06×103?C s-1)increased,part of theα-Fe soft magnetic phase(31.7vol.%)is suppressed,and a higher volume of Nd2Fe17Bxmetastable phases(47.5 vol.%)areformed.As a result,both the VIM-casting and LDED-processed Nd-Fe-B deposits exhibited poor magnetic properties.In contrast,employing the high values of V(>10-2m s-1)and R(1.45×106?C s-1)in the LPBF process resulted in the substantial formation of the Nd2Fe14B hard magnetic phase(55.8 vol.%)directly from the liquid,while theα-Fe soft magnetic phase and Nd2Fe17Bxmetastable phase precipitation are suppressed in the LPBF-processed Nd-Fe-B magnet.Additionally,crystallographic texture analysis reveals that the LPBF-processedNd-Fe-B magnets exhibit isotropic magnetic characteristics.Consequently,the LPBF-processed Nd-Fe-B deposit,exhibiting a coercivity of 656 k A m-1,remanence of 0.79 T and maximum energy product of 71.5 k J m-3,achieved an acceptable magnetic performance,comparable to other additive manufacturing processed Nd-Fe-B magnets from MQP(Nd-lean)Nd-Fe-Bpowder.

Erratum to:Deriving Temporal and Vertical Distributions of Methane in Xianghe Using Ground-based Fourier Transform Infrared and Gas-analyzer

“Diurnal variation of CH4 at the surface from spring to winter.The time units are in local time(+8 h UTC).The error bar is 1σfor all the observed hourly mean data within that season at that local time.”in the caption of Fig.8 on Page 604 should be“Diurnal variation of CH4 at the surface from spring to winter.The time units are in UTC.The error bar is 1σfor all the observed hourly mean data within that season at that local time.”

Estimate of Hydrofluorocarbon Emissions for 2012–16 in the Yangtze River Delta, China

Hydrofluorocarbons(HFCs)have been widely used in China as substitutes for ozone-depleting substances,the production and use of which are being phased out under the Montreal Protocol.China is a major consumer of HFCs around the world,with its HFC emissions in CO2-equivalent contributing to about 18%of the global emissions for the period2012-16.Three methods are widely used to estimate the emissions of HFCs-namely,the bottom-up method,top-down method and tracer ratio method.In this study,the tracer ratio method was adopted to estimate HFC emissions in the Yangtze River Delta(YRD),using CO as a tracer.The YRD region might make a significant contribution to Chinese totals owing to its rapid economic growth.Weekly flask measurements for ten HFCs(HFC-23,HFC-32,HFC-125,HFC-134 a,HFC-143 a,HFC-152 a,HFC-227 ea,HFC-236 fa,HFC-245 fa and HFC-365 mfc)were conducted at Lin’an Regional Background Station in the YRD over the period 2012-16,and the HFC emissions were 2.4±1.4 Gg yr-1 for HFC-23,2.8±1.2 Gg yr-1 for HFC-32,2.2±1.2 Gg yr-1 for HFC-125,4.8±4.8 Gg yr-1 for HFC-134 a,0.9±0.6 Gg yr-1 for HFC-152 a,0.3±0.3 Gg yr-1 for HFC-227 ea and 0.3±0.2 Gg yr-1 for HFC-245 fa.The YRD total HFC emissions reached 53 Gg CO2-e yr-1,contributing 34%of the national total.The per capita HFC CO2-equivalent emissions rate was 240 kg yr-1,while the values of per unit area emissions and per million GDP emissions reached 150 Mg km-2yr-1 and 3500 kg yr-1(million CNY GDP)-1,which were much higher than national or global levels.

Erratum to:Estimate of Hydrofluorocarbon Emissions for 2012-16 in the Yangtze River Delta,China

In the original version of this article,the unit of the YRD total HFC emissions“Gg CO2-e yr^−1”in the abstract should be Tg CO2-e yr^−1.On Page 581,in the fifth line from the left bottom,the unit of the total CO2-equivalent emissions of HFCs“Gg yr^−1”should be Tg yr^−1.

Dosimetric analysis of tomotherapy-based intensity-modulated radiotherapy with and without bone marrow sparing for the treatment of cervical cancer

Objective The aim of the study was to compare tomotherapy-based bone marrow-sparing intensity-mod- ulated radiotherapy （BMS-IMRT） with intensity-modulated radiotherapy （IMRT） without entering the pelvic bone marrow as a planning constraint in the treatment of cervical cancer after hysterectomy. Methods BMS-IMRT and IMRT plans were designed for a cohort of nine patients. The prescribed dose was 45 Gy in 1.8 Gy daily fractions, and 95% of the planned target volume received this dose. The doses were computed using a commercially available treatment planning system with the convolution/superposition algorithm. Plans were compared according to dose-volume histogram analysis in terms of planning target volume homogeneity and conformity indices （HI and CI） as well as organ at risk dose and volume parameters. Results BMS-IMRT had advantages over IMRT in terms of CI, but was equivalent to the latter in H1. V5, V10, V20, V30, and V40 of pelvic bone marrow in BMS-IMRT decreased by 0.06%, 17.33%, 22.19%, 13.85%, and 16.46%, respectively, compared with IMRT. Except for V30 of the small bowel and V30 and V40 of the bladder, no statistically significant differences were found between BMS-IMRT and IMRT in the small bowel, bladder, and rectum. Conclusion For cervical cancer patients receiving tomotherapy-based radiotherapy after hysterectomy, BMS-IMRT reduced pelvic bone marrow volume receiving low-dose radiation, and it may be conducive to preventing acute hematologic toxicity.

Pre-heating temperature induced flowability and wax deposition characteristics of crude oil adding wax inhibitors

This paper investigated the effects of pre-heating treatment temperatures(T_(pre))on the flowability and wax deposition characteristics of a typical waxy crude oil after adding wax inhibitors.It is found that there is little difference in wax precipitation exothermic characteristics of crude oils at different T_(pre),as well as the wax crystal solubility coefficient in the temperature range of 25-30℃.For the undoped crude oil,the flowability after wax precipitation gets much improved and the wax deposition is alleviated as T_(pre)increasing.At T_(pre)=50℃,the viscosity and wax deposition rate of crude oil adding wax inhibitors are higher than those of the undoped crude oil.When the T_(pre)increases to 60,70,and 80℃,the flowability of the doped crude oil are largely improved and the wax deposition is suppressed with the T_(pre)increase,but the wax content of wax deposit increases gradually.It is speculated that,on the one hand,the T_(pre)increase helps the dispersion of asphaltenes into smaller sizes,which facilitates the co-crystallization with paraffin waxes and generates more aggregated wax crystal flocs.This weakens the low-temperature gel structure and increases the solid concentration required for the crosslink to form the wax deposit.On the other hand,the decrease in viscosity increases the diffusion rate of wax molecules and accelerates the aging of wax deposits.The experimental results have important guiding significance for the pipeline transportation of doped crude oils.

A dosimetric evaluation of flattening filter-free volumetric modulated arc therapy for postoperative treatment of cervical cancer

Objective The aim of the study was to compare flattening filter-free(FFF) beams and conventional flattening filter(FF) beams in volumetric modulated arc therapy(VMAT) for cervical cancer after surgery, through a retrospective planning study.Methods VMAT plans of FFF beams and normal FF beams were designed for a cohort of 15 patients. The prescribed dose was 45 Gy to 1.8 Gy per fraction, and at least 95% of the planning target volume received this dose. Doses were computed with a commercially available treatment planning system using a Monte Carlo(MC) algorithm. Plans were compared according to dose-volume histogram analysis in terms of planning target volume homogeneity and conformity indices(HI and CI), as well as organs at risk(OAR) dose and volume parameters. Results FFF-VMAT was similar to FF-VMAT in terms of CI, but inferior to FF-VMAT considering HI. No statistically differences were observed between FFF-VMAT and FF-VMAT in following organ at risks including pelvic bone marrow, small bowel, bladder, rectum, and normal tissue(NT)..Conclusion For patients with cervical cancer after hysterectomy, the FFF beam achieved target and OAR dose distribution similar to that of the FF beam. Reduction of beam-on time in cervical cancer is beneficial.

紧耦合真空气雾化制备Fe-Cr合金粉末的特性表征

采用紧耦合真空气雾化法制备Fe-Cr合金粉末,通过不同目数的筛网进行筛分,得到0~25μm、25~53μm、53~105μm、105~150μm四个粒度段的粉末.使用氧氮分析仪、碳硫分析仪、电感耦合等离子体发射光谱仪分析雾化前后粉末化学成分,测定全粒度段及各粒度段的氧含量变化情况;采用扫描电镜、激光粒度仪等分析测试手段观察粉末表面形貌及表面微观组织并测定粉末粒径.结果表明:紧耦合真空气雾化制备Fe-Cr金属粉末化学成分可精确控制,全粒度段氧含量为0.024wt.%;冷却速度随粉末粒径的减小呈现指数级增长,随着粉末粒度段的增大,表面组织主要由胞状晶、柱状晶向树枝晶发展;各粒度段氧含量随粒径增大逐渐减小;空心粉的形成主要与袋式破碎机制和晶粒凝固收缩差有关.

Standard friction prediction model of long-distance hot oil pipelines

We developed a predictive model for the pipeline friction in the 520-730 m^3/h transmission range using the multi-layerperceptron-back-propagation(MLP-BP)method and analyzing the unit friction data after the pigging of a hot oil pipeline.In view of the shortcomings of the MLP-BP model,two optimization methods,the genetic algorithm(GA)and mind evolutionary algorithm(MEA),were used to optimize the MLP-BP model.The research results were applied to the standard friction prediction of three sections of a hot oil pipeline.After the GA and MEA optimizations,the average errors of the three sections were 0.0041 MPa for the GA and 0.0012 MPa for the MEA,and the mean-square errors were 0.083 and 0.067,respectively.The MEA-BP model prediction results were characterized by high precision and small dispersion.The MEABP prediction model was applied to the analysis of the wax formation 60 and 90 days after pigging.The analysis results showed that the model can effectively guide pipe pigging and optimization.There was little sample data for the individual transmission and oil temperature steps because the model was based on actual production data modeling and analysis,which may have affected the accuracy and adaptability of the model.

Deriving Temporal and Vertical Distributions of Methane in Xianghe Using Ground-based Fourier Transform Infrared and Gas-analyzer Measurements

Methane(CH4)is one of the most important greenhouse gases in the atmosphere,making it worthwhile to study its temporal and vertical distributions in source areas,e.g.,North China.For this purpose,a ground-based high-resolution Fourier transform infrared spectrometer(FTIR),the Bruker IFS 125 HR,along with an in-situ instrument,the Picarro G2301,were deployed in Xianghe County(39.8°N,117.0°E),Hebei Province,China.Data have been recorded since June2018.For the FTIR measurements,we used two observation modes to retrieve the mole fraction of CH4:the Total Carbon Column Observing Network(TCCON)method(retrieval algorithm:GGG2014),and the Network for the Detection of Atmospheric Composition Change(NDACC)method(retrieval algorithm:SFIT4).Combining FTIR with in-situ measurements,we found the temporal and vertical distributions of atmospheric CH4 within three vertical layers(near the ground,in the troposphere,and in the stratosphere),and throughout the whole atmosphere.Regarding the diurnal variation of CH4 near the ground,the concentration at night was higher than during the daytime.Regarding the seasonal variation,CH4 was low in spring and high in summer,for all three vertical layers.In addition,there was a peak of CH4 in winter near the ground,both in the troposphere and the whole atmosphere.We found that variation of CH4 in the tropospheric column was close to that of the in-situ measurements near the ground.Furthermore,the variations of CH4 in the stratospheric column could be influenced by vertical motions,since it was higher in summer and lower in winter.

Comparison of the effects of two typesof multileaf collimators on tumor control probabilityin radiotherapy for breast cancer after conservativesurgery based on the EUD model

Objective To compute and compare the tumor control probability(TCP) of volumetric modulated arc therapy(VMAT) for breast cancer after conservative surgery based on two types of multileaf collimator(MLC) through a retrospective planning study.Methods For a group of 9 patients diagnosed with left breast cancer,VMAT plan based on Agility MLC and beam modulator(BM) MLC were designed.The prescription dose was 50 Gy covering at least 95% of the planning target volume,2 Gy per fraction.TCPs were calculated according to dose-volume histogram(DVH) analysis.Results The TCP of the BM VMAT plan was slightly higher than that of the Agility VMAT plan(94.61% vs 94.23%) but was inferior with respect to delivery efficiency;the delivery time was reduced for Agility VMAT plan by 35% compared to BM VMAT plan.Conclusion For breast cancer radiation therapy after conservative surgery,BM VMAT plans provide slightly higher TCP while the delivery of Agility VMAT plans is significantly faster than the BM VMAT plans.

Modelling the Rheological Properties of Epoxy Asphalt Concrete

This paper presents an investigation into modelling the rheological properties of epoxy asphalt concrete( EAC) by using the Huet-Sayegh model. Complex modulus tests were conducted on EAC specimens at various temperature and loading frequency conditions. Dynamic modulus and phase angles obtained from the complex modulus tests were used in the construction of the Huet-Sayegh model. The dynamic modulus master curve was developed by the Huet-Sayegh model as well as the Burgers model for comparison purpose. The results showed that EAC exhibits typical rheological behavior whose dynamic modulus decreases with the increase of temperature while increases with the increase of frequency,and phase angles increase with the decrease of frequencies and the increase of temperatures. The Huet-Sayegh model predicts the dynamic modulus master curve of EAC very well and much better than the Burgers model over a wide range of frequencies.

Performance improvement of Ethylene-Vinyl Acetate Copolymer Pour Point Depressant(EVA PPD)by adding small dosages of Laurylamine(LA)

Lauramine is widely considered to be an asphaltene flocculant,but its effect on the modification of crude oil by PPDs has been little studied.In this paper,the effect of LA dosage on the rheology improvement of EVA PPDs(100 ppm)on Qinghai waxy crude oil was investigated through rheological measurement,wax precipitating analysis,granularity test and resins/asphaltenes FTIR analysis.Compared with pure EVA,the compounding of LA and EVA obviously enhances the agglomeration degree and reduces the number of fine wax crystals,thus further enhancing the rheology of the oil samples,and the best performance is at the LA dosage of 200 ppm.At relatively small LA dosages,the LA facilitates the adsorption of EVA molecules on the asphaltene surfaces,which favors the becoming of EVA/asphaltenes composite particles;but at relatively high LA dosages,the LA makes the asphaltenes more aggregated and disturbs the EVA adsorption on the asphaltenes,which is adverse for the formation of EVA/asphaltenes compound particles.The compound particles can serve as wax precipitating templates and significantly influence its morphology,thus further improving the crude oil rheology.In consequence,the rheology improvement of EVA PPDs on Qinghai waxy crude oil first increases and then decreases with increasing the LA dosage.

Co-adsorption behavior of aggregated asphaltenes and silica nanoparticles at oil/water interface and its effect on emulsion stability

In petroleum industry, crude oil emulsions are commonly formed in oilfields. The asphaltenes and fine particles in crude oil may affect the stability of the emulsions by adsorbing at the water/oil interface. In this research, the effect of silica nanoparticles and asphaltenes on emulsion stability is explored first. The asphaltenes are proved to benefit emulsion stability. Unlike the asphaltenes, however, the modified silica nanoparticles may have positive or negative effect on emulsion stability, depending on the asphaltene concentration and aggregation degree in the emulsions. Further, it is confirmed by conducting interfacial experiment that the asphaltenes and particles can adsorb at the interface simultaneously and determine the properties of the interfacial layer. More in-depth experiments concerning contact angle and asphaltene adsorption amount on the particles indicate that the asphaltenes can modify the wettability of the particles. Higher concentration and lower aggregation degree of the asphaltenes can increase their adsorption amount on the surface of particles and then improve the modification effectiveness of the particles. Resultantly, the particles with good modification effectiveness can enhance the emulsion stability while the particles with poor modification effectiveness will weaken the emulsion stability.

Adaptive protograph-based BICM-ID relying on the RJ-MCMC algorithm:a reliable and efficient transmission solution for plasma sheath channels

For reentry communication,owing to the influence of the highly dynamic plasma sheath(PS),the parasitic modulation effect can occur and the received phase shift keying(PSK)signal constellation can be severely rotated,leading to unacceptable demodulation performance degradation.In this work,an adaptive non-coherent bit-interleaved coded modulation with iterative decoding(BICM-ID)system with binary PSK(BPSK)modulation and protograph lowdensity parity-check under the PS channel is proposed.The proposed protograph-based BICMID(P-BICM-ID)system can achieve joint processing of demodulation and decoding,where the soft information is adaptively estimated by reversible-jump Markov chain Monte Carlo(RJMCMC)algorithms.Simulation results indicate that compared to existing algorithms,the proposed system can adapt well to the dynamic characteristics of the PS channel and can obtain a 5dB performance improvement at a bit error rate of 10^(-6).

Preface to Special Topic on Atmospheric Greenhouse Gas Measurement and Application in China

China initiated a national carbon trading market in December 2017.Commitments and actions to reduce greenhouse gas(GHG)emissions require consistent,reliable and timely information on GHG emissions.GHG monitoring and modeling studies provide GHG emission estimates to evaluate and guide progress towards emission reductions.GHG monitoring has mainly focused on global-scale background networks over the last few decades,while recent efforts have been made on regional and urban scales,such as projects in the Beijing-Tianjin-Hebei city cluster,in Paris,Washington-Baltimore.

Phantom-based evaluations of two binning algorithms for four-dimensional CT reconstruction in lung cancer radiation therapy

Objective: The purpose of this study was to evaluate the performance of the phase-binning algorithm and amplitude-binning algorithm for four-dimensional computed tomography(4DCT) reconstruction in lung cancer radiation therapy. Methods: Quasar phantom data were used for evaluation. A phantom of known geometry was mounted on a four-dimensional(4D) motion platform programmed with twelve respiratory waves(twelve lung patients trajectories) and scanned with a Philips Brilliance Big bore 16-slice CT simulator. The 4DCT images were reconstructed using both phase- and amplitude-binning algorithms. Internal target volumes(ITVs) of the phase- and amplitude-binned image sets were compared by evaluation of shape and volume distortions. Results: The phantom experiments illustrated that, as expected, maximum inhalation occurred at the 0% amplitude and maximum exhalation occurred at the 50% amplitude of the amplitude-binned 4DCT image sets. The amplitude-binned algorithm rendered smaller ITV than the phase-binning algorithm. Conclusion: The amplitude-binning algorithm for 4DCT reconstruction may have a potential advantage in reducing the margin and protecting normal lung tissue from unnecessary irradiation.

Five-year oncologic outcomes and prognostic factors for locally advanced low rectal cancer after low anterior resection

Objective： The aim of the study is to investigate the longterm oncologic outcomes including local recurrence, distant metastases and overall survival （OS） for patients with low rectal cancer underwent low anterior resection （LAR） with total mesorectal excision （TME）, and to analyze the prognostic factors for them. Methods： Between January 2001 and December 2009, 147 patients with clinical stage II and III rectal cancers located 3-6 cm from the anal verge underwent LAR with TME without temporary diverting stoma. The median distal resection margin （DRM） was 1.0 （range, 0.3-5） cm. Anastomostic leakage occurred in 29 （19.7%） patients. Thirty patients received surgery alone, 20 patients received preoperative chemoradiotherapy （CRT）, 43 patients received postoperative CRT, and adjuvant chemotherapy was administered for 108 patients. The median cycle of adjuvant chemotherapy was 6 （range, 2-20） cycles. The median followup was 74.8 （range, 30.1-146.3） months. Results： In all patients, 5-year recurrence-free survival （RFS）, disease-free survival （DFS） and OS were 70.4%, 54.2% and 60.5%, respectively. Forty-three （29.3%） patients suffered local recurrence. Patients received preoperative CRT with a downstaging yp0/1 who had a better 5-year RFS, DFS and OS, which were 100%, 90.9%, and 90.9%, respectively. For patients with pathologic stage Ⅱ and stage Ⅲ, the 5-year RFS, DFS, and OS were 79.2% and 60.1%, 67.9% and 39.1%, 72.1% and 48.2%, respectively. On multivariable analysis, RFS was associated with anostomostic leakage, DFS was associated with anastomostic leakage and pathologic N stage, and OS was associated with anastomostic leakage, pathologic N and T stage. For patients with anastomostic leakage, the 5-year RFS, DFS, and OS were 51.7%, 32.4%, and 38.3%, respectively, which were worse than that for patients without anastomostic leakage, the latter were 75.2%, 59.7%, 65.7%, respectively （P 〈 0.05）. DRM and radiotherapy were associated with RFS on univariable analysis （P 〈 0.05）, but not on multivariable analysis. Tumor grade was prognostic factors for RFS and OS on univariable analysis, but not on multivariable analysis. The other factors including sex, age, tumor size and adjuvant chemotherapy were not associated with RFS, DFS and OS on univariable analysis. Conclusion： For patients with low rectal caner underwent LAR and TME, the long-term oncologic outcomes were satisfactory for patients with stage yp0/1, but not for patients with pathologic stage II1. Anastomositic leakage negatively affect long-term oncologic outcomes. Radiotherpy, adjuvant chemotherapy and distal resection margin were not associated with long-term outcomes.

Dosimetric comparison of different multileaf collimators in volumetric modulated arc therapy for malignant pleural mesothelioma

Objective The aiom of the study was to compare the impacts of two types of multileaf collimators （MLC） [standard MLC with a width of 10 mm （sMLC） and micro-MLC with a width of 5 mm （mMLC）] on volumetric modulated arc therapy （VMAT） planning for malignant pleural mesothelioma. Methods VMAT for ten patients with inoperable malignant pleural mesotheliomas was retrospectively planned with the sMLC and mMLC. Histogram-based dose-volume parameters of the planning target vol- ume （PTV） [conformity index （CI） and homogeneous index （HI）] and organs-at-risk were compared for VMAT plans with sMLC （sMLC-VMAT） and mMLC （mMLC-VMAT）. Results The mMLC-VMAT plans were more efficient （average delivery time： 2.67±1.49 min） than the sMLC-VMAT plans （average delivery time： 4.21 ± 2.03 min; P 〈 0.05）. Moreover, compared to the sMLC plans, the mMLC plans demonstrated advantages in the dose coverage of the PTV （CI 0.75 ± 0.08 vs 0.73± 0.09; HI 1.09 ±0.02 vs 1.10± 0.02）, although the difference was not statistically significant （P 〉 0.05）. In addition, significant dose sparing in the fraction of the ipsilateral lung volume receiving 〉 20 Gy （V20; 54.72± 27.08 vs 58.52 ± 29.30） and 〉 30 Gy （V30; 42.74 ± 27.86 vs 46.86± 31.49） radiation, respectively, was observed for the mMLC plans （P 〈 0.05）. Conclusion Comparing sMLC-VMAT and mMLC-VMAT not only demonstrated the higher efficiency and better optimal target coverage of mMLC-VMAT, but also considerably improved the dose sparing of the ipsilateral lung in the VMAT plans for mali qnant pleural mesothelioma.

Analysis on the Problems of Solutions of Water Conservancy & Hydropower Engineering Cost Management

With the continuous development of society and economy in China, the number of water conserv ancy & hydropower engineering in China increases unceasingly and China s water conserv ancy industry also enters into the stage of rapid development. The construction of water conserv ancy & hydropower engineering promotes social and economic development, so in order to safeguard the benefits of the engineering, cost management shall be done well, which is also an important channel for companies engaging in water conservancy & hydropower engineering to obtain economic benefits. Based on this the paper firstly investigates the problems in water conserv ancy & hydropower engineering cost management and then brings up relevant solutions.