Removal of cadmium from aqueous solutions using red mud granulated with cement

A novel adsorbent was prepared from granular red mud mixed with cement and its potential to be a suitable adsorbent for the removal of cadmium ions from aqueous solutions was evaluated. The wet red mud was directly mixed up with cement at different mass fractions of 2%-8% and their properties were investigated. Based on the textural characteristics and strength, the granular red mud with 2% addition of cement maintaining for 6 d is identified to have better properties. The batch adsorption experiments for adsorption of Cd2+ ions from solution were performed at 30, 40 and 50 °C at different initial concentrations under the condition of constant pH of 6.5. The equilibrium adsorption was found to increase with the increase of temperature during the adsorption process. Langmuir adsorption isotherm model was found to match the experimental adsorption isotherm better. The kinetics of adsorption was modeled using a pseudo second order kinetic model and the model parameters were estimated.

Influence of carbon coating prepared by microwave pyrolysis on properties of LiNi_(1/3) Mn_(1/3) Co_(1/3) O_2

A novel synthesis method of carbon-coated LiNil/3Mnl/3COl/302 cathode material for lithium-ion battery was reported. The carbon coating was produced from a precursor, glucose, by microwave-pyrolysis method. The prepared powders were characterized by scanning electron microscopy （SEM）, X-ray diffraction （XRD）, X-ray fluorescence （XRF） and charge/discharge tests. XRD results indicate that the carbon coating does not change the phase structure of LiNil/3Mnl/3C01/302 material. SEM results show that the surface of spherical carbon-coated material becomes rough. Electrochemical performance results show that the carbon coating can improve the cycling performance of LiNii/3Mnl/3C01/302. The specific discharge capacity retention of the carbon-coated LiNi1/3Mnt/3Col/30z reached 85.0%-96.0% at the 50th cycle at 0.2C rate, and the specific discharge capacity retention is improved at a high rate.

Regeneration of waste activated carbon after extracting gold with steam under microwave heating:Optimization using response surface methodology

The technology that waste activated carbon after extracting gold is regenerated with steam under microwave heating was studied. The influence of the activation temperature, activation duration and steam flow rate on iodine adsorption value and regeneration yield of activated carbon was investigated. The response surface methodology （RSM） technique was utilized to optimize the process conditions. The optimum conditions for the preparation of activated carbon are identified to be activation temperature of 831 ℃, activation duration of 40 min and steam flow rate of 2.67 mL/min. The optimum conditions result in an activated carbon with an iodine number of 1048 mg/g and a yield of 40%, and the BET surface area evaluated using nitrogen adsorption isotherm is 1493 m2/g, with total pore volume of 1.242 cm3/g. And the pore structure of activated carbon regenerated is mainly composed of micropores and a small amount of mesopores.

Process optimization for treatment of methyltin mercaptide effluents using modified semi-coke

The central composite process optimization was performed by response surface methodology technique using a design for the treatment of methyltin mercaptide with modified semi-coke. The semi-coke from the coal industry was suitably modified by treating it with phosphoric acid, with a thermal activation process. The objective of the process optimization is to reduce the chemical oxygen demand （COD） and NH4＋-N in the methyltin mercaptide industrial effluent. The process variables considered for process optimization are the semi-coke dosage, adsorption time and effluent pH. The optimized process conditions are identified to be a semi-coke dosage of 80 g/L, adsorption time of 90 min and a pH value of 8.34. The ANOVA results indicate that the adsorbent dosage and pH are the significant parameters, while the adsorption time is insignificant, possibly owing to the large range of adsorption time chosen. The textural characteristics of modified semi-coke were analyzed using scanning electron microscopy and nitrogen adsorption isotherm. The average BET surface area of modified semi-coke is estimated to be 915 mE/g, with the average pore volume of 0.71 cm3/g and a average pore diameter of 3.09 nm, with micropore volume contributing to 52.36%.

Preparation of microsized hematite powder from ferrous sulfate via microwave calcination

The preparation of microsized hematite powder from ferrous sulfate using microwave calcination was investigated based on the TG/DTG curves. The decomposition of industrial ferrous sulfate under air atmosphere was divided into three stages, and a ferrous sulfate sample added with 15% Fe_2O_3 could strongly absorb microwave energy. Therefore, preparing hematite powder from ferrous sulfate using microwave calcination was feasible. Hematite was obtained under the following optimized conditions: calcination temperature, 850 °C; microwave power, 650 W; and sample amount, 40 g. The obtained hematite satisfied the first-grade quality requirements. The total ferrum value was more than 58%, and the total sulfur and phosphorus contents were less than 0.5% and 0.2%, respectively. X-ray powder diffraction and scanning electron microscopy were used to characterize the structure and morphology of microsized hematite powder. The particles were non-spherical in shape, and the average particle size distribution was 10.45 μm. This work provides new potential applications for waste ferrous sulfate.