Two-dimensional(2D)flume experiments are useful in investigating the performances of floating breakwaters(FBs),including hydrodynamic performances,motion responses,and mooring forces.Designing a reasonable gap between...Two-dimensional(2D)flume experiments are useful in investigating the performances of floating breakwaters(FBs),including hydrodynamic performances,motion responses,and mooring forces.Designing a reasonable gap between the flume wall and the FBs is a critical step in 2D flume tests.However,research on the effect of the gap on the accuracy of 2D FB experimental results is scarce.To address this issue,a numerical wave tank is developed using CFD to estimate the wave-FB interaction of a moored dual-cylindrical FB,and the results are compared to experimental data from a previously published work.There is good agreement between them,indicating that the numerical model is sufficiently accurate.The numerical model is then applied to explore the effect of gap diffraction on the performance of FBs in2D experiments.It was discovered that the nondimensional gap length L_(Gap)/W_(Pool)should be smaller than 7.5%to ensure that the relative error of the transmission coefficient is smaller than 3%.The influence of the gap is also related to the entering wave properties,such as the wave height and period.展开更多
The Y 2O 3-CeO 2-ZrO 2 powders were prepared using a co-precipitation process and the corresponding coatings were prepared by plasma spraying. The results show that an optimal composition exists in Y 2O 3-doped ...The Y 2O 3-CeO 2-ZrO 2 powders were prepared using a co-precipitation process and the corresponding coatings were prepared by plasma spraying. The results show that an optimal composition exists in Y 2O 3-doped CeO 2-ZrO 2, but not in CeO 2-doped Y 2O 3-ZrO 2. The powders mainly contain tetragonal phase and a trace amount of monoclinic phase. The homogeneity in composition, large agglomerate size, ideal particle size distribution and high flowability were obtained. The as-sprayed coatings are composed of non-transformable tetragonal phase, tz′structure, and resistant to transformation under thermal or mechanical stresses.展开更多
Ni-25Al-15Cr （atomic percent, %） alloy was directionally solidified （DS） under argon atmosphere in an Al2O3-SiO2 ceramic mold by standard Bridgman method. The microstructure of the as-fabricated alloy was studied ...Ni-25Al-15Cr （atomic percent, %） alloy was directionally solidified （DS） under argon atmosphere in an Al2O3-SiO2 ceramic mold by standard Bridgman method. The microstructure of the as-fabricated alloy was studied using optical microscope, X-ray diffractometer, and scanning electron microscope. The alloy consisting of dendritic β- NiAl phase, interdendritic γ/γ′ phase, and transient layer γ′ phase, has been investigated. This alloy exhibits superplastic deformation behavior at 1 273-1 373 K over an initial strain rate range of 8. 35×10 ^-4 -1. 67×10^-2s^-1. The maximum elongation of 280% with strain rate sensitivity index m= 0. 22 was obtained at the temperature of 1 323 K and an initial strain rate of 8. 35×10^-3s^-1. Transmission electron microscopy （TEM） observations indicate that the superplastic deformation stems from the balance between high resistance （by dislocation sliding） and strain softening （by dynamic recovery and recrystallization）.展开更多
基金financially supported by China National Funds for Distinguished Young Scientists(Grant No.52025112)the Key Projects of the National Natural Science Foundation of China(Grant No.52331011)。
文摘Two-dimensional(2D)flume experiments are useful in investigating the performances of floating breakwaters(FBs),including hydrodynamic performances,motion responses,and mooring forces.Designing a reasonable gap between the flume wall and the FBs is a critical step in 2D flume tests.However,research on the effect of the gap on the accuracy of 2D FB experimental results is scarce.To address this issue,a numerical wave tank is developed using CFD to estimate the wave-FB interaction of a moored dual-cylindrical FB,and the results are compared to experimental data from a previously published work.There is good agreement between them,indicating that the numerical model is sufficiently accurate.The numerical model is then applied to explore the effect of gap diffraction on the performance of FBs in2D experiments.It was discovered that the nondimensional gap length L_(Gap)/W_(Pool)should be smaller than 7.5%to ensure that the relative error of the transmission coefficient is smaller than 3%.The influence of the gap is also related to the entering wave properties,such as the wave height and period.
文摘The Y 2O 3-CeO 2-ZrO 2 powders were prepared using a co-precipitation process and the corresponding coatings were prepared by plasma spraying. The results show that an optimal composition exists in Y 2O 3-doped CeO 2-ZrO 2, but not in CeO 2-doped Y 2O 3-ZrO 2. The powders mainly contain tetragonal phase and a trace amount of monoclinic phase. The homogeneity in composition, large agglomerate size, ideal particle size distribution and high flowability were obtained. The as-sprayed coatings are composed of non-transformable tetragonal phase, tz′structure, and resistant to transformation under thermal or mechanical stresses.
文摘Ni-25Al-15Cr （atomic percent, %） alloy was directionally solidified （DS） under argon atmosphere in an Al2O3-SiO2 ceramic mold by standard Bridgman method. The microstructure of the as-fabricated alloy was studied using optical microscope, X-ray diffractometer, and scanning electron microscope. The alloy consisting of dendritic β- NiAl phase, interdendritic γ/γ′ phase, and transient layer γ′ phase, has been investigated. This alloy exhibits superplastic deformation behavior at 1 273-1 373 K over an initial strain rate range of 8. 35×10 ^-4 -1. 67×10^-2s^-1. The maximum elongation of 280% with strain rate sensitivity index m= 0. 22 was obtained at the temperature of 1 323 K and an initial strain rate of 8. 35×10^-3s^-1. Transmission electron microscopy （TEM） observations indicate that the superplastic deformation stems from the balance between high resistance （by dislocation sliding） and strain softening （by dynamic recovery and recrystallization）.
