This study aims to develop a low-cost refractometer for measuring the sucrose content of fruit juice,which is an important factor affecting human health.While laboratory-grade refractometers are expensive and unsuitab...This study aims to develop a low-cost refractometer for measuring the sucrose content of fruit juice,which is an important factor affecting human health.While laboratory-grade refractometers are expensive and unsuitable for personal use,existing low-cost commercial options lack stability and accuracy.To address this gap,we propose a refractometer that replaces the expensive CCD sensor and light source with a conventional LED and a reasonably priced CMOS sensor.By analyzing the output waveform pattern of the CMOS sensor,we achieve high precision with a personal-use-appropriate accuracy of 0.1%.We tested the proposed refractometer by conducting 100 repeated measurements on various fruit juice samples,and the results demonstrate its reliability and consistency.Running on a 48 MHz ARM processor,the algorithm can acquire data within 0.2 seconds.Our low-cost refractometer is suitable for personal health management and small-scale production,providing an affordable and reliable method for measuring sucrose concentration in fruit juice.It improves upon the existing low-cost options by offering better stability and accuracy.This accessible tool has potential applications in optimizing the sucrose content of fruit juice for better health and quality control.展开更多
In precision machining of complex curved surface parts with high performance, geometry accuracy is not the only constraint, but the performance should also be met. Performance of this kind of parts is closely related ...In precision machining of complex curved surface parts with high performance, geometry accuracy is not the only constraint, but the performance should also be met. Performance of this kind of parts is closely related to the geometrical and physical parameters, so the final actual size and shape are affected by multiple source constraints, such as geometry, physics, and performance. These parts are rather difficult to be manufactured and new manufacturing method according to performance requirement is urgently needed. Based on performance and manufacturing requirements for complex curved surface parts, a new classification method is proposed, which divided the complex curved surface parts into two categories： surface re-design complex curved surface parts with multi-source constraints（PRCS） and surface unique complex curved surface parts with pure geometric constraints（PUCS）. A correlation model is constructed between the performance and multi-source constraints for PRCS, which reveals the correlation between the performance and multi-source constraints. A re-design method is also developed. Through solving the correlation model of the typical paws performance-associated surface, the mapping relation between the performance-associated surface and the related removal amount is obtained. The explicit correlation model and the method for the corresponding related removal amount of the performance-associated surface are built based on the classification of surface re-design complex curved surface parts with multi-source constraints. Research results have been used in the actual processing of the typical parts such as radome, common bottom components, nozzle, et al., which shows improved efficiency and accuracy of the precision machining for the surface re-design parts with complex curved surface.展开更多
Parts with varied curvature features play increasingly critical roles in engineering, and are often machined under high-speed continuous-path running mode to ensure the machining efficiency. However, the continuous-pa...Parts with varied curvature features play increasingly critical roles in engineering, and are often machined under high-speed continuous-path running mode to ensure the machining efficiency. However, the continuous-path running trajectory error is significant during high-feed-speed machining, which seriously restricts the machining precision for such parts with varied curvature features. In order to reduce the continuous-path running trajectory error without sacrificing the machining efficiency, a pre-compensation method for the trajectory error is proposed. Based on the formation mechanism of the continuous-path running trajectory error analyzed, this error is estimated in advance by approximating the desired toolpath with spline curves. Then, an iterative error pre-compensation method is presented. By machining with the regenerated toolpath after pre-compensation instead of the uncompensated toolpath, the continuous-path running trajectory error can be effectively decreased without the reduction of the feed speed. To demonstrate the feasibility of the proposed pre-compensation method, a heart curve toolpath that possesses varied curvature features is employed. Experimental results indicate that compared with the uncompensated processing trajectory, the maximum and average machining errors for the pre-compensated processing trajectory are reduced by 67.19% and 82.30%, respectively. An easy to implement solution for high efficiency and high precision machining of the parts with varied curvature features is provided.展开更多
The explosion flow field in five straight pipes with different diameters and one bending pipe selected from a domestic coal mine are studied by the method of numerical simulation. And the results show that,both in the...The explosion flow field in five straight pipes with different diameters and one bending pipe selected from a domestic coal mine are studied by the method of numerical simulation. And the results show that,both in the straight and bending pipes, the pressure wave and velocity wave are accelerated by the rising of reaction rate. As the explosion progressed, with the temperature reaching approximately 3000 K, only one pressure wave and one reaction rate wave were observed, while several velocity waves were found.The larger diameter presented the highest relative pressure as well as the largest velocity increase and subsequent decrease inside the tube. The bent pipes caused both turbulence and kinetic energy to increase, resulting in the acceleration of the reaction rate. The burning time was 7.4% shorter than the burning time observed for the straight pipe. Based on these results, designing one explosion resistance device, and in the practical engineering applications, it was to be proved to meet the security requirements fully.展开更多
Ni-TiN nanocomposite coatings were prepared by ultrasonic electrodeposition, and the effects of the surfactants on the coatings were investigated and the microstructure and micro rigidity of the coatings were characte...Ni-TiN nanocomposite coatings were prepared by ultrasonic electrodeposition, and the effects of the surfactants on the coatings were investigated and the microstructure and micro rigidity of the coatings were characterized. Samples were also submitted to corrosion tests in 3% NaCl solution. The results showed that the surfactants had great effects on Ni-TiN nanocomposite coatings. The composite coatings prepared by ultrasonic electrodeposition with the surfactants were better than that of the coatings prepared without surfactants. The favorable properties of Ni-TiN nanocomposite coatings were prepared with the mixing of the non-ion and positive ion surfactants. The concentration of the mixing was 80 mg/L, and the ratio of the non-ion and positive ion surfactants was 1： 2.展开更多
文摘This study aims to develop a low-cost refractometer for measuring the sucrose content of fruit juice,which is an important factor affecting human health.While laboratory-grade refractometers are expensive and unsuitable for personal use,existing low-cost commercial options lack stability and accuracy.To address this gap,we propose a refractometer that replaces the expensive CCD sensor and light source with a conventional LED and a reasonably priced CMOS sensor.By analyzing the output waveform pattern of the CMOS sensor,we achieve high precision with a personal-use-appropriate accuracy of 0.1%.We tested the proposed refractometer by conducting 100 repeated measurements on various fruit juice samples,and the results demonstrate its reliability and consistency.Running on a 48 MHz ARM processor,the algorithm can acquire data within 0.2 seconds.Our low-cost refractometer is suitable for personal health management and small-scale production,providing an affordable and reliable method for measuring sucrose concentration in fruit juice.It improves upon the existing low-cost options by offering better stability and accuracy.This accessible tool has potential applications in optimizing the sucrose content of fruit juice for better health and quality control.
基金supported by Key Program of National Natural Science Foundation of China(Grant No.50835001)Program for New Century Excellent Talents in University,China(Grant No.NCET-13-0081)
文摘In precision machining of complex curved surface parts with high performance, geometry accuracy is not the only constraint, but the performance should also be met. Performance of this kind of parts is closely related to the geometrical and physical parameters, so the final actual size and shape are affected by multiple source constraints, such as geometry, physics, and performance. These parts are rather difficult to be manufactured and new manufacturing method according to performance requirement is urgently needed. Based on performance and manufacturing requirements for complex curved surface parts, a new classification method is proposed, which divided the complex curved surface parts into two categories： surface re-design complex curved surface parts with multi-source constraints（PRCS） and surface unique complex curved surface parts with pure geometric constraints（PUCS）. A correlation model is constructed between the performance and multi-source constraints for PRCS, which reveals the correlation between the performance and multi-source constraints. A re-design method is also developed. Through solving the correlation model of the typical paws performance-associated surface, the mapping relation between the performance-associated surface and the related removal amount is obtained. The explicit correlation model and the method for the corresponding related removal amount of the performance-associated surface are built based on the classification of surface re-design complex curved surface parts with multi-source constraints. Research results have been used in the actual processing of the typical parts such as radome, common bottom components, nozzle, et al., which shows improved efficiency and accuracy of the precision machining for the surface re-design parts with complex curved surface.
基金Supported by National Natural Science Foundation of China(Grant Nos.51575087,51205041)Science Fund for Creative Research Groups(Grant No.51321004)+1 种基金Basic Research Foundation of Key Laboratory of Liaoning Educational Committee,China(Grant No.LZ2014003)Research Project of Ministry of Education of China(Grant No.113018A)
文摘Parts with varied curvature features play increasingly critical roles in engineering, and are often machined under high-speed continuous-path running mode to ensure the machining efficiency. However, the continuous-path running trajectory error is significant during high-feed-speed machining, which seriously restricts the machining precision for such parts with varied curvature features. In order to reduce the continuous-path running trajectory error without sacrificing the machining efficiency, a pre-compensation method for the trajectory error is proposed. Based on the formation mechanism of the continuous-path running trajectory error analyzed, this error is estimated in advance by approximating the desired toolpath with spline curves. Then, an iterative error pre-compensation method is presented. By machining with the regenerated toolpath after pre-compensation instead of the uncompensated toolpath, the continuous-path running trajectory error can be effectively decreased without the reduction of the feed speed. To demonstrate the feasibility of the proposed pre-compensation method, a heart curve toolpath that possesses varied curvature features is employed. Experimental results indicate that compared with the uncompensated processing trajectory, the maximum and average machining errors for the pre-compensated processing trajectory are reduced by 67.19% and 82.30%, respectively. An easy to implement solution for high efficiency and high precision machining of the parts with varied curvature features is provided.
基金supported by National Natural Science Foundation of China (No. 51174113)National Key Basic Research and Development Program (No. 2011CB201206)National Key Scientific Apparatus Development of Special Item (No. 2012YQ24012705)
文摘The explosion flow field in five straight pipes with different diameters and one bending pipe selected from a domestic coal mine are studied by the method of numerical simulation. And the results show that,both in the straight and bending pipes, the pressure wave and velocity wave are accelerated by the rising of reaction rate. As the explosion progressed, with the temperature reaching approximately 3000 K, only one pressure wave and one reaction rate wave were observed, while several velocity waves were found.The larger diameter presented the highest relative pressure as well as the largest velocity increase and subsequent decrease inside the tube. The bent pipes caused both turbulence and kinetic energy to increase, resulting in the acceleration of the reaction rate. The burning time was 7.4% shorter than the burning time observed for the straight pipe. Based on these results, designing one explosion resistance device, and in the practical engineering applications, it was to be proved to meet the security requirements fully.
基金National Natural Science Foundation of China(No.50475108)Natural Science Foundation of Liaoning Province,China(No.20042123)
文摘Ni-TiN nanocomposite coatings were prepared by ultrasonic electrodeposition, and the effects of the surfactants on the coatings were investigated and the microstructure and micro rigidity of the coatings were characterized. Samples were also submitted to corrosion tests in 3% NaCl solution. The results showed that the surfactants had great effects on Ni-TiN nanocomposite coatings. The composite coatings prepared by ultrasonic electrodeposition with the surfactants were better than that of the coatings prepared without surfactants. The favorable properties of Ni-TiN nanocomposite coatings were prepared with the mixing of the non-ion and positive ion surfactants. The concentration of the mixing was 80 mg/L, and the ratio of the non-ion and positive ion surfactants was 1： 2.
