Effect of solution treatment on the microstructure,phase transformation behavior and functional properties of NiTiNb ternary shape memory alloys fabricated via laser powder bed fusion in-situ alloying

Post-heat treatment is commonly employed to improve the microstructural homogeneity and enhance the mechanical performances of the additively manufactured metallic materials.In this work,a ternary(NiTi)91Nb9(at.%)shape memory alloy was produced by laser powder bed fusion(L-PBF)using pre-alloyed NiTi and elemental Nb powders.The effect of solution treatment on the microstructure,phase transformation behavior and mechanical/functional performances was investigated.The in-situ alloyed(NiTi)91Nb9 alloy exhibits a submicron cellular-dendritic structure surrounding the supersaturated B2-NiTi matrix.Upon high-temperature(1273 K)solution treatment,Nb-rich precipitates were precipitated from the supersaturated matrix.The fragmentation and spheroidization of the NiTi/Nb eutectics occurred during solution treatment,leading to a morphological transition from mesh-like into rod-like and sphere-like.Coarsening of theβ-Nb phases occurred with increasing holding time.The martensite transformation temperature increases after solution treatment,mainly attributed to:(i)reduced lattice distortion due to the Nb expulsion from the supersaturated B2-NiTi,and(ii)the Ti expulsion from theβ-Nb phases that lowers the ratio Ni/Ti in the B2-NiTi matrix,which resulted from the microstructure changes from non-equilibrium to equilibrium state.The thermal hysteresis of the solutionized alloys is around 145 K after 20%pre-deformation,which is comparable to the conventional NiTiNb alloys.A short-term solution treatment(i.e.at 1273 K for 30 min)enhances the ductility and strength of the as-printed specimen,with the increase of fracture stress from(613±19)MPa to(781±20)MPa and the increase of fracture strain from(7.6±0.1)%to(9.5±0.4)%.Both the as-printed and solutionized samples exhibit good tensile shape memory effects with recovery rates>90%.This work suggests that post-process heat treatment is essential to optimize the microstructure and improve the mechanical performances of the L-PBF in-situ alloyed parts.

Open cellular magnesium alloys for biodegradable orthopaedic implants

Replication processing using NaCl spaceholders offers the possibility to produce cellular structures for a range of Mg alloys. Four Mg alloys (AZ63, M2, ZM21 and MZX211) were processed into open cellular structures with a pore size near 500 μm and a porosity of 75% using an optimized NaCl leaching procedure. The production method was found to be robust and yielded samples of acceptable strength and stiffness. Their dissolution rate (by H2 release in simulated body fluid) and mechanical properties (by cyclic compression) were measured. For all 4 alloys the initial mechanical properties mimic those of cancellous bone;however, the dissolution rate is too high for direct use in the human body, leading to excessive hydrogen evolution and overly rapid degradation of mechanical properties. Further post-processing of the material is thus required.

Size effect on the microstructure, phase transformation behavior, and mechanical properties of NiTi shape memory alloys fabricated by laser powder bed fusion

In this work,NiTi samples with different thicknesses(0.15-1.00 mm)were fabricated by laser powder bed fusion(LPBF)under variable scanning speeds(500-1200 mm s^(-1)).The densification behavior,phase transformation behavior,and mechanical properties of the sample with different thicknesses are studied.The results indicate a strong size effect in the LPBF-fabricated NiTi alloy.The decrease of the sample thickness results in(i)the increase of porosity,(ii)the decrease of the number of adhered NiTi powder particles at the surface,(iii)the monotonous decrease of the martensitic transformation temperatures(MTTs),and(iv)the decrease of the shape recovery temperature.The influence of sample thickness on the melt-pool behavior,and thus the microstructure and performance of NiTi alloys are discussed.It is suggested that the melt-pool is deeper and narrower in the thin samples than in the thick samples.We conclude that,apart from the LPBF process conditions,the sample dimensions have also to be considered to fabricate NiTi structures with predictable properties.