Many agricultural fields across the country have a high degree of variability in soil type and water holding capacity that affects irrigation management. One way to overcome problems associated with the field variabil...Many agricultural fields across the country have a high degree of variability in soil type and water holding capacity that affects irrigation management. One way to overcome problems associated with the field variability for improving irrigation management is to utilize a site-specific irrigation system. This system applies water to match the needs of individual management zones within a field. A real-time continuous soil moisture measurement is essential for the success of site-specific irrigation systems. Recently the National Aeronautics and Space Administration (NASA) developed sensor technology that records the global positioning system (GPS) signal reflected from the surface of Earth, which estimates the dielectric properties of soil and can be used to estimate soil moisture contents. The overall objective of this study was to determine the feasibility of utilizing GPS-based technology developed by NASA for soil moisture measurements and to determine the influence of soil type, soil compaction, and ground cover on the measurements. The results showed strong positive correlations between soil moisture and reflected signals. Other factors (soil compaction and soil type), were not significantly related to reflectivity and did not significantly change the relationship between reflectivity and soil moisture contents. In addition, ground cover (rye crop) did not significantly reduce reflectivity. Therefore, this system could be used as a real-time and continuous nonintrusive soil moisture sensor for site-specific irrigation scheduling and watershed management.展开更多
Accurate soil moisture content measurements are vital to precision irrigation management. Remote sensing using the microwave spectrum (such as GPS signals) has been used for measuring large area soil moisture contents...Accurate soil moisture content measurements are vital to precision irrigation management. Remote sensing using the microwave spectrum (such as GPS signals) has been used for measuring large area soil moisture contents. In our previous work, we estimated surface soil moisture contents for bare soil using a GPS Delay Mapping Receiver (DMR) developed by NASA. However, the effect of vegetation was not considered in these studies. Hence the objectives of this study were to: 1) investigate the feasibility of using DMR to determine soil moisture content in cotton production fields;2) evaluate the attenuation effect of vegetation (cotton) on reflected GPS signal. Field experiments were conducted during the 2013 and 2014 growing seasons in South Carolina. GPS antennas were mounted at three heights (1.6, 2.7, and 4.2 m) over cotton fields to measure reflected GPS signals (DMR readings). DMR readings, soil core samples, and plant measurements were collected about once a week and attenuation effect of plant canopy was calculated. Results showed that DMR was able to detect soil moisture changes within one week after precipitation events that were larger than 25 mm per day. However, the DMR readings were poorly correlated with soil volumetric water content during dry periods. Attenuation effect of plant canopy was not significant. For irrigation purpose, the results suggested that the sensitivity of reflected GPS signals to soil moisture changes needed to be further studied before this technology could be utilized for irrigation scheduling in cotton production. Refinement of this technology will expand the use of advanced remote sensing technology for site-specific and timely irrigation scheduling. This would eliminate the need to install moisture sensors in production fields, which can interfere with farming operations and increase production costs.展开更多
Recent increases in irrigated hectares in the Southeastern US have enabled growers to obtain higher yields through applying nutrients through irrigation water. Therefore, many growers apply nutrients through irrigatio...Recent increases in irrigated hectares in the Southeastern US have enabled growers to obtain higher yields through applying nutrients through irrigation water. Therefore, many growers apply nutrients through irrigation systems, known as fertigation. Currently, there are no practical decision-making tools available for variable-rate application of nitrogen (N) through overhead sprinkler irrigation systems. Therefore, field tests were conducted on cotton (Gossypium hirsutum L.) during the 2016 and 2017 growing seasons to 1) adapt the Clemson sensor-based N recommendation algorithms from a single side-dress application to multiple applications through an overhead irrigation system;and 2) to compare sensor-based VRFS with conventional nutrient management methods in terms of N use efficiency (NUE) and crop responses on three soil types. Two seasons of testing Clemson N prediction algorithms to apply multiple applications of N were very promising. The multiple applications of N compared to the grower’s conventional methods (even though less N was applied) had no impact on yields in either growing season. There was no difference in cotton yields between 101 and 135 kg/ha N applications in either management zone. Also, there were no differences in yield between sensor-based, multiple N applications and conventional N management techniques. In relation to comparisons of the sensor methods only applying N in three or four applications, statistically increased yields compared to single or split applications in 2016. Applying N in four applications, statistically increased yields compared to single, split or triple applications in 2017. When the sensor-based methods were compared to the grower’s conventional methods averaged over four treatments, the sensor-based N applications reduced fertilizer requirement by 69% in 2016 and 57% in 2017 compared to grower’s conventional methods. When comparing N rates among the four sensor-based methods (three or four) applications, increased N rates by 22 kg/ha in 2016 and 26 kg/ha in 2017 compared to single or split applications but increased the cotton lint yields by 272 and 139 kg/ha, for 2016 and 2017, respectively.展开更多
Nutrients are injected through overhead irrigation systems at a uniform rate in a process known as fertigation. The highly variable soils in the Southeastern US pose challenges for effective fertigation. Currently, th...Nutrients are injected through overhead irrigation systems at a uniform rate in a process known as fertigation. The highly variable soils in the Southeastern US pose challenges for effective fertigation. Currently, there is no variable-rate fertigation system available to apply the correct amount of N within a field through an overhead irrigation system. Therefore, the objective of this study was to develop and test a variable-rate N application system that works independently of irrigation water flow for site-specific N application. The variable-rate fertigation system (VRFS) was designed to apply different rates N using a pulse width modulation technique. The VRFS utilized the Clemson Lateral Irrigation Control software which controlled the solenoids in each zone by turning the N supply on and off (pulsing) for each zone. In this study, four tests were conducted to determine the uniformity of the VRFS. In test # 1, the pump output showed a linear slope relationship and was the same for water and N. In test # 2, nozzle flow and uniformity were determined using four different irrigation system travel speeds at N application rates of 31, 59, 88, and 113 kg/ha. There was a strong correlation (R2 = 0.9998) between irrigation system speed and N rate. In test # 3, the uniformity across the length of the irrigation system was determined. The nozzles produced an average flow of 31.1, 58.7, 87.6, and 112.7 kg N/ha with an overall average error of 0.1% across all N rates. Results also showed the system was capable of accurately applying N based on prescription maps with an error of less than 1.8%. Test # 4 was conducted to determine the accuracy of the map-based controller system for applying variable rate N. There was a strong correlation between target N and actual N rates (R2 = 0.9999). In summary, the VRFS applied the correct amounts of N within each zone by either manually controlling the pulsing mechanism or utilizing a prescription map to apply different rates throughout the field.展开更多
Applying insufficient nitrogen (N) in a highly responsive crop, such as corn, results in lower grain yield, quality, and profits. On the other hand, when nitrogen is applied in excess of crop needs, profit is reduced ...Applying insufficient nitrogen (N) in a highly responsive crop, such as corn, results in lower grain yield, quality, and profits. On the other hand, when nitrogen is applied in excess of crop needs, profit is reduced and negative environmental consequences are likely. The objective of this study was to develop and employ a sensor-based algorithm to determine the mid-season N requirements for deficit-irrigated corn in Coastal Plain soils. The algorithm was developed using varied prescription rate N plot on two soil types. The test plots received nine different rates of N fertilizer, replicated 5 times in plots of each soil type using a Randomized Complete Block design. A 6-row GreenSeeker optical sensor was used to measure plant NDVI, between the V6 to V8 growth stages. The sensor readings were used to develop an algorithm to be used in the estimation of side-dress N application in corn. The NDVI sensor readings were collected at the V6 to V8 growth stage during the 2015 and 2016 growing seasons correlated with actual corn yields (R2 > 0.68, p < 0.001). In-Season Estimated yield (INSEY) was used along with the actual yield to produce a yield potential for each growing season for deficit-irrigated corn crop. In summary, the algorithm developed from the NDVI readings reduced N application rates by 21% and 34% in soil types 1 and 2, respectively, compared to the normal grower practice (226 kg N/ha) with no reduction in corn yields.展开更多
Nutrient application systems are designed to apply a relatively uniform amount of a fertilizer to agricultural fields. However, considerable variation in soil texture and other characteristics often occurs within and ...Nutrient application systems are designed to apply a relatively uniform amount of a fertilizer to agricultural fields. However, considerable variation in soil texture and other characteristics often occurs within and across production fields, which could have a major impact on fertilizer management strategies. Therefore, uniform application of a fertilizer over the entire field can be both costly and environmentally unsound. Due to their rugged and fool-proof design, crankshaft type piston pumps are widely used in agriculture. The on-the-go outlet flow of these pumps can only be varied by changing the drive shaft speed for each pump stroke setting. But only a limited range of flow rates can be achieved by changing the drive shaft speed. There is a need for an electronic controller, which can adjust the pump stroke on-the-go, for real-time, variable-rate application of crop nutrients. The Clemson “Electro-me-chanical controller for adjusting pump stroke on-the-go” was designed to replace the current manual stroke adjustment system on positive displacement piston pumps. This affordable system can be retrofitted on most John Blue - piston pumps for real-time adjustment of the pump stroke and can be controlled using pre-described position sequences (map-based) or real-time sensor commands (such as optical, pressure, and flow sensors) combined with fertilizer calculation algorithms. In addition, it can adjust pump stroke manually, using an eclectic dial from the tractor’s cab.展开更多
Cotton root growth is often hindered in the Southeastern U.S. due to the presence of root-restricting soil layers. Tillage must be used to temporarily remove this compacted soil layer to allow root growth to depths ne...Cotton root growth is often hindered in the Southeastern U.S. due to the presence of root-restricting soil layers. Tillage must be used to temporarily remove this compacted soil layer to allow root growth to depths needed to sustain plants during periods of drought. However, the use of a uniform depth of tillage may be an inefficient use of energy due to the varying depth of this root-restricting layer. Therefore, the objective of this project was to develop and test equipment for controlling tillage depth “on-the-go” to match the soil physical parameters, and to determine the effects of site-specific tillage on soil physical properties, energy requirements, and plant responses in cotton production. Site-specific tillage operations reduced fuel consumption by 45% compared to conventional constant-depth tillage. Only 20% of the test field required tillage at recommended depth of 38-cm deep for Coastal Plain soils. Cotton taproot length in the variable-depth tillage plots was 96% longer than those in the no-till plots (39 vs. 19.8 cm). Statistically, there was no difference in cotton lint yield between conventional and the variable-depth tillage. Deep tillage (conventional or variable-rate) increased cotton lint yields by 20% compared to no-till.展开更多
文摘Many agricultural fields across the country have a high degree of variability in soil type and water holding capacity that affects irrigation management. One way to overcome problems associated with the field variability for improving irrigation management is to utilize a site-specific irrigation system. This system applies water to match the needs of individual management zones within a field. A real-time continuous soil moisture measurement is essential for the success of site-specific irrigation systems. Recently the National Aeronautics and Space Administration (NASA) developed sensor technology that records the global positioning system (GPS) signal reflected from the surface of Earth, which estimates the dielectric properties of soil and can be used to estimate soil moisture contents. The overall objective of this study was to determine the feasibility of utilizing GPS-based technology developed by NASA for soil moisture measurements and to determine the influence of soil type, soil compaction, and ground cover on the measurements. The results showed strong positive correlations between soil moisture and reflected signals. Other factors (soil compaction and soil type), were not significantly related to reflectivity and did not significantly change the relationship between reflectivity and soil moisture contents. In addition, ground cover (rye crop) did not significantly reduce reflectivity. Therefore, this system could be used as a real-time and continuous nonintrusive soil moisture sensor for site-specific irrigation scheduling and watershed management.
文摘Accurate soil moisture content measurements are vital to precision irrigation management. Remote sensing using the microwave spectrum (such as GPS signals) has been used for measuring large area soil moisture contents. In our previous work, we estimated surface soil moisture contents for bare soil using a GPS Delay Mapping Receiver (DMR) developed by NASA. However, the effect of vegetation was not considered in these studies. Hence the objectives of this study were to: 1) investigate the feasibility of using DMR to determine soil moisture content in cotton production fields;2) evaluate the attenuation effect of vegetation (cotton) on reflected GPS signal. Field experiments were conducted during the 2013 and 2014 growing seasons in South Carolina. GPS antennas were mounted at three heights (1.6, 2.7, and 4.2 m) over cotton fields to measure reflected GPS signals (DMR readings). DMR readings, soil core samples, and plant measurements were collected about once a week and attenuation effect of plant canopy was calculated. Results showed that DMR was able to detect soil moisture changes within one week after precipitation events that were larger than 25 mm per day. However, the DMR readings were poorly correlated with soil volumetric water content during dry periods. Attenuation effect of plant canopy was not significant. For irrigation purpose, the results suggested that the sensitivity of reflected GPS signals to soil moisture changes needed to be further studied before this technology could be utilized for irrigation scheduling in cotton production. Refinement of this technology will expand the use of advanced remote sensing technology for site-specific and timely irrigation scheduling. This would eliminate the need to install moisture sensors in production fields, which can interfere with farming operations and increase production costs.
文摘Recent increases in irrigated hectares in the Southeastern US have enabled growers to obtain higher yields through applying nutrients through irrigation water. Therefore, many growers apply nutrients through irrigation systems, known as fertigation. Currently, there are no practical decision-making tools available for variable-rate application of nitrogen (N) through overhead sprinkler irrigation systems. Therefore, field tests were conducted on cotton (Gossypium hirsutum L.) during the 2016 and 2017 growing seasons to 1) adapt the Clemson sensor-based N recommendation algorithms from a single side-dress application to multiple applications through an overhead irrigation system;and 2) to compare sensor-based VRFS with conventional nutrient management methods in terms of N use efficiency (NUE) and crop responses on three soil types. Two seasons of testing Clemson N prediction algorithms to apply multiple applications of N were very promising. The multiple applications of N compared to the grower’s conventional methods (even though less N was applied) had no impact on yields in either growing season. There was no difference in cotton yields between 101 and 135 kg/ha N applications in either management zone. Also, there were no differences in yield between sensor-based, multiple N applications and conventional N management techniques. In relation to comparisons of the sensor methods only applying N in three or four applications, statistically increased yields compared to single or split applications in 2016. Applying N in four applications, statistically increased yields compared to single, split or triple applications in 2017. When the sensor-based methods were compared to the grower’s conventional methods averaged over four treatments, the sensor-based N applications reduced fertilizer requirement by 69% in 2016 and 57% in 2017 compared to grower’s conventional methods. When comparing N rates among the four sensor-based methods (three or four) applications, increased N rates by 22 kg/ha in 2016 and 26 kg/ha in 2017 compared to single or split applications but increased the cotton lint yields by 272 and 139 kg/ha, for 2016 and 2017, respectively.
文摘Nutrients are injected through overhead irrigation systems at a uniform rate in a process known as fertigation. The highly variable soils in the Southeastern US pose challenges for effective fertigation. Currently, there is no variable-rate fertigation system available to apply the correct amount of N within a field through an overhead irrigation system. Therefore, the objective of this study was to develop and test a variable-rate N application system that works independently of irrigation water flow for site-specific N application. The variable-rate fertigation system (VRFS) was designed to apply different rates N using a pulse width modulation technique. The VRFS utilized the Clemson Lateral Irrigation Control software which controlled the solenoids in each zone by turning the N supply on and off (pulsing) for each zone. In this study, four tests were conducted to determine the uniformity of the VRFS. In test # 1, the pump output showed a linear slope relationship and was the same for water and N. In test # 2, nozzle flow and uniformity were determined using four different irrigation system travel speeds at N application rates of 31, 59, 88, and 113 kg/ha. There was a strong correlation (R2 = 0.9998) between irrigation system speed and N rate. In test # 3, the uniformity across the length of the irrigation system was determined. The nozzles produced an average flow of 31.1, 58.7, 87.6, and 112.7 kg N/ha with an overall average error of 0.1% across all N rates. Results also showed the system was capable of accurately applying N based on prescription maps with an error of less than 1.8%. Test # 4 was conducted to determine the accuracy of the map-based controller system for applying variable rate N. There was a strong correlation between target N and actual N rates (R2 = 0.9999). In summary, the VRFS applied the correct amounts of N within each zone by either manually controlling the pulsing mechanism or utilizing a prescription map to apply different rates throughout the field.
文摘Applying insufficient nitrogen (N) in a highly responsive crop, such as corn, results in lower grain yield, quality, and profits. On the other hand, when nitrogen is applied in excess of crop needs, profit is reduced and negative environmental consequences are likely. The objective of this study was to develop and employ a sensor-based algorithm to determine the mid-season N requirements for deficit-irrigated corn in Coastal Plain soils. The algorithm was developed using varied prescription rate N plot on two soil types. The test plots received nine different rates of N fertilizer, replicated 5 times in plots of each soil type using a Randomized Complete Block design. A 6-row GreenSeeker optical sensor was used to measure plant NDVI, between the V6 to V8 growth stages. The sensor readings were used to develop an algorithm to be used in the estimation of side-dress N application in corn. The NDVI sensor readings were collected at the V6 to V8 growth stage during the 2015 and 2016 growing seasons correlated with actual corn yields (R2 > 0.68, p < 0.001). In-Season Estimated yield (INSEY) was used along with the actual yield to produce a yield potential for each growing season for deficit-irrigated corn crop. In summary, the algorithm developed from the NDVI readings reduced N application rates by 21% and 34% in soil types 1 and 2, respectively, compared to the normal grower practice (226 kg N/ha) with no reduction in corn yields.
文摘Nutrient application systems are designed to apply a relatively uniform amount of a fertilizer to agricultural fields. However, considerable variation in soil texture and other characteristics often occurs within and across production fields, which could have a major impact on fertilizer management strategies. Therefore, uniform application of a fertilizer over the entire field can be both costly and environmentally unsound. Due to their rugged and fool-proof design, crankshaft type piston pumps are widely used in agriculture. The on-the-go outlet flow of these pumps can only be varied by changing the drive shaft speed for each pump stroke setting. But only a limited range of flow rates can be achieved by changing the drive shaft speed. There is a need for an electronic controller, which can adjust the pump stroke on-the-go, for real-time, variable-rate application of crop nutrients. The Clemson “Electro-me-chanical controller for adjusting pump stroke on-the-go” was designed to replace the current manual stroke adjustment system on positive displacement piston pumps. This affordable system can be retrofitted on most John Blue - piston pumps for real-time adjustment of the pump stroke and can be controlled using pre-described position sequences (map-based) or real-time sensor commands (such as optical, pressure, and flow sensors) combined with fertilizer calculation algorithms. In addition, it can adjust pump stroke manually, using an eclectic dial from the tractor’s cab.
文摘Cotton root growth is often hindered in the Southeastern U.S. due to the presence of root-restricting soil layers. Tillage must be used to temporarily remove this compacted soil layer to allow root growth to depths needed to sustain plants during periods of drought. However, the use of a uniform depth of tillage may be an inefficient use of energy due to the varying depth of this root-restricting layer. Therefore, the objective of this project was to develop and test equipment for controlling tillage depth “on-the-go” to match the soil physical parameters, and to determine the effects of site-specific tillage on soil physical properties, energy requirements, and plant responses in cotton production. Site-specific tillage operations reduced fuel consumption by 45% compared to conventional constant-depth tillage. Only 20% of the test field required tillage at recommended depth of 38-cm deep for Coastal Plain soils. Cotton taproot length in the variable-depth tillage plots was 96% longer than those in the no-till plots (39 vs. 19.8 cm). Statistically, there was no difference in cotton lint yield between conventional and the variable-depth tillage. Deep tillage (conventional or variable-rate) increased cotton lint yields by 20% compared to no-till.
