Coseismic and postseismic slip ruptures for 2015Mw 6.4 Pishan earthquake constrained by static GPS solutions

On 3 July 2015, a Mw 6.4 earthquake occurred on a blind fault struck Pishan, Xinjiang,China. By combining Crustal Movement Observation Network of China（CMONOC） and other Static Global Positioning System（GPS） sites surrounding Pishan region, it provides a rare chance for us to constrain the slip rupture for such a moderate event. The maximum displacement is up to 12 cm, 2 cm for coseismic and postseismic deformation, respectively,and both the deformation patterns show a same direction moving northeastward. With rectangular dislocation model, a magnitude of Mw6.48, Mw6.3 is calculated based on coseismic, postseismic deformation respectively. Our result indicates the western Kunlun range is still moving toward Tarim Basin followed by an obvious postseismic slip associated with this earthquake. To determine a more reasonable model for postseismic deformation, a longer GPS dataset will be needed.

Analysis of the common model error on velocity field under Colored noise model by GPS and InSAR: A case study in the Nepal and everest region

The accuracy of the velocity field will be affected by the noise model and common mode errors through GPS time series analysis.In order to analyze the influence of these two factors on the accuracy of the velocity field,two kinds of data are used,including the three-year observation from 20 permanent GPS stations with high spatial correlation in the Everest,which is about 650 km from north to south and 1068 km from east to west,and three-year 80 ascending images and 141 descending images from sentinel-1A,which are processed by GAMIT/GLOBK software and Small Baseline Subset-Interferometric Synthetic Aperture Radar method(SBAS-InSAR),respectively.The vertical deformation rate is solved by time series analysis through a self-made adaptive algorithm.In the analysis,the linear change rate,period,half period coefficient,and residual sequence of all stations are solved by using James L.Davis periodic model.The noise type of residual sequence is analyzed by the power spectrum model.The spatio-temporal correlated noise,Common Mode Error(CME),is extracted by the Principal Component Analysis(PCA)and Karhunen-Loeve(KLE)methods.The results show that noises can be best described by“flicker noise+white noise”model.After the removal of CME,the R^(2) estimates of all stations are above 0.8,with RMS value of velocity field decreasing from 1.428 mm/yr to 1.062 mm/yr and 1.063 mm/yr to 0.815 mm/yr,in N and E directions,respectively,indicating that the influence of CME can't be ignored in the extraction of the high-precision velocity field in the Nepal and Everest region.

Noise reduction and periodic signal extraction for GNSS height data in the study of vertical deformation

Global navigation satellite system(GNSS)technique has irreplaceable advantages in the continuous monitoring of surface deformation.Reducing noise to improve the signal-to-noise ratio(SNR)and extract the concerned signals is of great significance.As an improved algorithm of empirical mode decomposition(EMD),complete ensemble empirical mode decomposition with adaptive noise(CEEMDAN)algorithm has better signal processing ability.Using the CEEMDAN algorithm,the height time series of 29GNSS stations in Chinese mainland were analyzed,and good denoising effects and extraction from periodic signals were achieved.The numerical results showed that the annual signal obtained with the CEEMDAN algorithm was significantly based on Lomb_Scargle spectrum analysis,and large differences in the long-term signals were found between the stations at different locations in Chinese mainland.With respect to data denoising,compared with the EMD and wavelet denoising algorithms,the CEEMDAN algorithm respectively improved the SNR by 29.35% and 36.54%,increased the correlation coefficient by 8.67% and 11.96%,and reduced root mean square error(RMSE)by 44.68% and 43.48%,indicating that the CEEMDAN algorithm had better denoising behavior than the other two algorithms.In addition,the results demonstrated that different denoising methods had little influence on estimating the annual vertical deformation velocity.The extraction of periodic signals showed that more components were retained by using the CEEMDAN algorithm than the EMD algorithm,which indicated that the CEEMDAN algorithm had advantages over frequency aliasing.In conclusion,the CEEMDAN algorithm was recommended for processing the GNSS height time series to analyze the vertical deformation due to its excellent features of denoising and the extraction of periodic signals.