Estimating weak rock mass modulus has historically proven difficult although this mechanical property is an important input to many types of geotechnical analyses. An empirical database of weak rock mass modulus with ...Estimating weak rock mass modulus has historically proven difficult although this mechanical property is an important input to many types of geotechnical analyses. An empirical database of weak rock mass modulus with associated detailed geotechnical parameters was assembled from plate loading tests per- formed at underground mines in Nevada, the Bakhtiary Dam project, and Portugues Dam project. The database was used to assess the accuracy of published single-variate models and to develop a multivari- ate model for predicting in-situ weak rock mass modulus when limited geoteehnical data are available. Only two of the published models were adequate for predicting modulus of weak rock masses over lim- ited ranges of alteration intensities, and none of the models provided good estimates of modulus over a range of geotechnical properties. In light of this shortcoming, a multivariate model was developed from the weak rock mass modulus dataset, and the new model is exponential in form and has the following independent variables： （1） average block size or joint spacing, （2） field estimated rock strength, （3） dis- continuity roughness, and （4） discontinuity infilling hardness. The multivariate model provided better estimates of modulus for both hard-blocky rock masses and intensely-altered rock masses.展开更多
The purpose of this paper is to establish confidence in anticipated minimum bond strength for inflatable rock bolts by comparing the bond strength to variable geotechnical conditions using the rock mass rating （RMR）...The purpose of this paper is to establish confidence in anticipated minimum bond strength for inflatable rock bolts by comparing the bond strength to variable geotechnical conditions using the rock mass rating （RMR） system. To investigate a correlation between these parameters, the minimum bond strength of pull-out tested inflatable rock bolts was compared to the RMR of the rock in which these bolts were placed. Bond strength vs. RMR plots indicate that expected minimum bond strength is positively corre- lated with RMR; however, the correlation is not strong. Cumulative percent graphs indicate that 97~; of pull-out tests result in a minimum bond strength of 3.3 and 1.7 ton/m in RMR/〉 45 and 〈45, respectively. Although lower bond strengths are more commonly encountered in low RMR ground, high bond strengths are possible as well, yielding higher variability in bond strengths in low RMR ground. Bond strength of friction bolts relies on contact between the rock bolt and drill hole. Experience in Nevada indicates that RMR is known to affect both the quality and consistency of drill holes which likely affects bond strength. Drilling and bolting in low RMR ground is more sensitive to drilling and bolting practices, and strategies for maximizing bond strength in these conditions are discussed.展开更多
基金funded by the National Institute of Occupational Safety and Health through research contract 200-2011-39965(Principal Investigator Dr.Kallu)University of Nevada,Reno,NV
文摘Estimating weak rock mass modulus has historically proven difficult although this mechanical property is an important input to many types of geotechnical analyses. An empirical database of weak rock mass modulus with associated detailed geotechnical parameters was assembled from plate loading tests per- formed at underground mines in Nevada, the Bakhtiary Dam project, and Portugues Dam project. The database was used to assess the accuracy of published single-variate models and to develop a multivari- ate model for predicting in-situ weak rock mass modulus when limited geoteehnical data are available. Only two of the published models were adequate for predicting modulus of weak rock masses over lim- ited ranges of alteration intensities, and none of the models provided good estimates of modulus over a range of geotechnical properties. In light of this shortcoming, a multivariate model was developed from the weak rock mass modulus dataset, and the new model is exponential in form and has the following independent variables： （1） average block size or joint spacing, （2） field estimated rock strength, （3） dis- continuity roughness, and （4） discontinuity infilling hardness. The multivariate model provided better estimates of modulus for both hard-blocky rock masses and intensely-altered rock masses.
文摘The purpose of this paper is to establish confidence in anticipated minimum bond strength for inflatable rock bolts by comparing the bond strength to variable geotechnical conditions using the rock mass rating （RMR） system. To investigate a correlation between these parameters, the minimum bond strength of pull-out tested inflatable rock bolts was compared to the RMR of the rock in which these bolts were placed. Bond strength vs. RMR plots indicate that expected minimum bond strength is positively corre- lated with RMR; however, the correlation is not strong. Cumulative percent graphs indicate that 97~; of pull-out tests result in a minimum bond strength of 3.3 and 1.7 ton/m in RMR/〉 45 and 〈45, respectively. Although lower bond strengths are more commonly encountered in low RMR ground, high bond strengths are possible as well, yielding higher variability in bond strengths in low RMR ground. Bond strength of friction bolts relies on contact between the rock bolt and drill hole. Experience in Nevada indicates that RMR is known to affect both the quality and consistency of drill holes which likely affects bond strength. Drilling and bolting in low RMR ground is more sensitive to drilling and bolting practices, and strategies for maximizing bond strength in these conditions are discussed.
