聚氨酯泡沫注浆修复材料泡孔结构特征及抗压性能研究进展

聚氨酯泡沫(PUF)注浆修复材料以轻质高强、快凝高膨胀等优势,在基础设施修复加固领域得到了广泛的应用。抗压性能是工程修复材料十分重要的力学指标之一,而材料的微观结构对其宏观力学行为有决定性影响。近年来,国内外专家学者对PUF注浆修复材料的微观结构特性和抗压性能进行了大量研究,但尚未见到系统性总结。本文介绍了PUF注浆修复材料的定义及反应过程,综述了其微观泡孔结构特性、压缩应力-应变关系和本构模型,从宏微观角度讨论了其变形和破坏机理,总结了密度、试件尺寸、应变率和特殊环境工况对压缩性能的影响机理及规律,最后展望了PUF注浆修复材料未来的研究方向。

基于改性壳聚糖膜净化的超高效液相色谱-四极杆/静电场轨道阱质谱法测定牛奶中5种兽药残留

本研究通过在壳聚糖膜(chitosan membrane,CSM)表面接枝长碳链,获得了十八烷基三甲氧基硅烷改性的壳聚糖膜(C_(18)-CSM),将其作为分散固相萃取吸附剂对牛奶基质进行净化,并结合超高效液相色谱-四极杆/静电场轨道阱质谱(UHPLC-Q/Exactive Orbitrap MS)建立了牛奶中氧氟沙星、恩诺沙星、环丙沙星、地西泮和甲硝唑的测定方法。利用扫描电子显微镜、傅里叶变换红外光谱仪和接触角测试仪对C_(18)-CSM材料进行表征。对牛奶样品的前处理条件进行优化,最优条件如下:提取溶剂为5%甲酸乙腈,NaCl用量为1 g,萃取次数为1次,C_(18)-CSM用量为20 mg。采用Hypersil GOLD VANQUISH色谱柱(100 mm×2.1 mm,1.9μm)进行分离,以0.1%甲酸水溶液和0.1%甲酸乙腈作为流动相进行梯度洗脱,流速为0.3 mL/min,进样量为1μL,柱温为25℃,在电喷雾电离源正离子模式下进行检测。在优化的前处理条件下,5种兽药在0.5~100μg/L范围内具有良好的线性关系,相关系数(r^(2))≥0.9970,检出限(LOD)为0.2μg/L,定量限(LOQ)为0.5μg/L。5种兽药在3个加标水平(0.5、1、5μg/L)下的回收率为79.5%~115%,日内精密度为7.0%~13%(n=6),日间精密度为1.3%~11%(n=3)。实验结果表明,本文所建立方法操作简便,准确可靠,能够满足牛奶中5种兽药残留的同时检测。

N6-甲基腺苷在疾病中的研究进展

N6-甲基腺苷(m6A)修饰是由甲基化酶和去甲基化酶调节,导致一个动态和可逆的过程。m6A水平的变化涉及广泛的细胞过程,包括核RNA输出、mRNA代谢、蛋白质翻译和RNA剪接,与各种疾病有很强的相关性。本文旨在归纳和总结mRNA中m6A表达水平的变化在常见三类疾病中的作用和机制,以及基于m6A在mRNA中水平变化作为药物干预靶点的研究趋势。

Galerkin-based quasi-smooth manifold element(QSME)method for anisotropic heat conduction problems in composites with complex geometry

The accurate and efficient analysis of anisotropic heat conduction problems in complex composites is crucial for structural design and performance evaluation. Traditional numerical methods, such as the finite element method(FEM), often face a trade-off between calculation accuracy and efficiency. In this paper, we propose a quasi-smooth manifold element(QSME) method to address this challenge, and provide the accurate and efficient analysis of two-dimensional(2D) anisotropic heat conduction problems in composites with complex geometry. The QSME approach achieves high calculation precision by a high-order local approximation that ensures the first-order derivative continuity.The results demonstrate that the QSME method is robust and stable, offering both high accuracy and efficiency in the heat conduction analysis. With the same degrees of freedom(DOFs), the QSME method can achieve at least an order of magnitude higher calculation accuracy than the traditional FEM. Additionally, under the same level of calculation error, the QSME method requires 10 times fewer DOFs than the traditional FEM. The versatility of the proposed QSME method extends beyond anisotropic heat conduction problems in complex composites. The proposed QSME method can also be applied to other problems, including fluid flows, mechanical analyses, and other multi-field coupled problems, providing accurate and efficient numerical simulations.

Experimental study of the influencing factors and mechanisms of the pressure-reduction and augmented injection effect by nanoparticles in ultra-low permeability reservoirs

Nanoparticles(NPs)have gained significant attention as a functional material due to their ability to effectively enhance pressure reduction in injection processes in ultra-low permeability reservoirs.NPs are typically studied in controlled laboratory conditions,and their behavior in real-world,complex environments such as ultra-low permeability reservoirs,is not well understood due to the limited scope of their applications.This study investigates the efficacy and underlying mechanisms of NPs in decreasing injection pressure under various injection conditions(25—85℃,10—25 MPa).The results reveal that under optimal injection conditions,NPs effectively reduce injection pressure by a maximum of 22.77%in core experiment.The pressure reduction rate is found to be positively correlated with oil saturation and permeability,and negatively correlated with temperature and salinity.Furthermore,particle image velocimetry(PIV)experiments(25℃,atmospheric pressure)indicate that the pressure reduction is achieved by NPs through the reduction of wall shear resistance and wettability change.This work has important implications for the design of water injection strategies in ultra-low permeability reservoirs.

Endobronchial metastasis secondary to renal clear cell carcinoma:A case report

BACKGROUND Endobronchial metastases(EBMs)are tumours that metastasise from a malignant tumour outside the lungs to the central and subsegmental bronchi,and are visible under a bronchofibrescope.Most EBMs are formed by direct invasion or metastasis of intrathoracic malignant tumours,such as lung cancer,oesophageal cancer or mediastinum tumours.Renal cell carcinoma(RCC),accounting for 2%to 3%of all tumours,is a common malignant tumour of the urinary system.Renal clear cell carcinoma(RCCC)constitutes the predominant pathological subtype of RCC,comprising approximately 70%to 80%of all RCC cases.RCCC can spread and metastasise through arterial,venous and lymphatic circulation to almost all organs of the body.Moreover,lung,bone,liver,brain and local recurrence are the most common metastatic neoplasms of RCCC.However,EBM from RCCC has a low complication rate and is often misdiagnosed as primary lung cancer.CASE SUMMARY A 71-year-old male patient who had undergone radical left nephrectomy 7 years prior due to RCCC was referred to our hospital due to a 1-mo history of productive cough.The results of an enhanced chest CT scan indicated the presence of a soft tissue nodule in the upper lobe of the left lung,and flexible bronchoscopy revealed a hypervascular lesion in the bronchus of the left lung's superior lobe.Therefore,the patient underwent thoracoscopic left superior lobe wedge resection,and pathology confirmed EBM from the RCCC.CONCLUSION EBM from RCCC has a low incidence and no characteristic clinical manifestations in the early stage.If a bronchial tumour is found in a patient with RCCC,the possibility of bronchial metastatic cancer should be considered.

Noncanonical pyroptosis pathway: a promising target of traditional Chinese medicine in the treatment of sepsis-related injury

Sepsis is a life-threatening disease of organ failure caused by dysregulated host responses to infection and other infectious factors.Multi-organ injury is the leading cause of high mortality and septic shock during sepsis.Recent studies suggest that noncanonical pyroptosis,characterized mainly by the direct activation of caspase-11-gasdermin D-mediated pyroptosis by cytoplastic lipopolysaccharide,is closely related to sepsis-related organ injury.Here,this review summarizes recent advances in the regulatory mechanisms and targeted natural products from traditional Chinese medicine of the noncanonical pyroptosis pathway in sepsis-related injury.

Primary Malignant Melanoma of the Larynx:Case Report and Literature Review

Primary malignant melanoma of the larynx is extremely rare.This paper reports a case of a patient with primary malignant melanoma of the larynx.Preoperative laryngoscopy revealed a cauliflower-like mass in the supraglottic region,and a CT scan of the pharynx suggested laryngeal cancer with cervical lymph node metastasis.The patient underwent a total laryngectomy with lymph node dissection,and postoperative pathology confirmed a malignant melanoma in the supraglottic region of the larynx.

新型聚氨酯弹性体注浆材料的压缩尺寸效应及应变率效应

为了解决现有风电基础注浆加固材料强度低、抗变形能力弱及可注性差等难题,制备了一种新型聚氨酯弹性体注浆材料。在考虑尺寸效应和应变率效应的影响下进行了单轴压缩试验研究,得到了压缩应力-应变关系曲线,提出了一种适用于该聚氨酯弹性体注浆材料的四参数唯象本构模型。结果表明:在该材料达到极限破坏之前,其应力-应变关系分为弹性阶段、屈服阶段、应变软化阶段三个阶段;材料的弹性模量、抗压强度、软化应力、能量密度等力学参数随应变率增大而增大,随试件尺寸的增大呈现先减小后增大的趋势,且相比尺寸效应,应变率效应的影响更为显著。本工作提出的四参数唯象本构模型能准确地表征本材料在不同尺寸时的压缩应力-应变关系。此本构模型为该聚氨酯弹性体注浆材料的理论计算和工程应用提供了重要的科学依据。

Health risk assessment of heavy metals in soils and crops in a mining area(Au-Ag-Cutrona-oil et al.) of the Nanyang Basin, Henan Province, China

Heavy metal distribution in mining areas has always been a hot research topic due to the special environment of these areas. This study aims to explore the impact of heavy metal pollution on soils and crops in the study area, ensure the safety of local crops and the health of local residents, and provide a basis for the subsequent environmental restoration and the prevention and control of environmental pollution. Based on the analysis of the heavy metal concentrations in local soils and crops, the study investigated the spatial distribution, pollution degrees, and potential ecological risks of heavy metals in the farmland of a mining area in the southeastern Nanyang Basin, Henan province, China explored the sources of heavy metals and assessed the health risks caused by crop intake. The results of this study are as follows. The root soils of crops in the study area suffered heavy metal pollution to varying degrees. The degree of heavy metal pollution in maize fields is higher than that in wheat fields, and both types of fields suffer the most severe Cd pollution. Moreover, the root soils of different crops suffer compound pollution.The root soils in the maize fields suffer severe compound pollution at some sampling positions, whose distribution is similar to that of the mining area. Cd poses the highest potential ecological risks among all heavy metals, and the study area mainly suffers low and moderate comprehensive potential ecological risks. The principal component analysis(PCA) shows that the distribution of Zn, Cd, Pb, and As in soils of the study area is mainly affected by anthropogenic factors such as local mining activities;the distribution of Cr and Ni is primarily controlled by the local geological background;the distribution of Hg is mainly affected by local vehicle exhaust emissions, and the distribution of Cu is influenced by both human activities and the geological background. Different cereal crops in the study area are polluted with heavy metals dominated by Cd and Ni to varying degrees, especially wheat. As indicated by the health risk assessment results, the intake of maize in the study area does not pose significant human health risks;however, Cu has high risks to human health, and the compound heavy metal pollution caused by the intake of wheat in the study area poses risks to the health of both adults and children. Overall, the soils and crops in the study area suffer a high degree of heavy metal pollution, for which mining activities may be the main reason.

Experimental study of the mechanism of nanofluid in enhancing the oil recovery in low permeability reservoirs using microfluidics

Due to the low porosity and low permeability in unconventional reservoirs,a large amount of crude oil is trapped in micro-to nano-sized pores and throats,which leads to low oil recovery.Nanofluids have great potential to enhance oil recovery(EOR)in low permeability reservoirs.In this work,the regulating ability of a nanofluid at the oil/water/solid three-phase interface was explored.The results indicated that the nanofluid reduced the oil/water interfacial tension by two orders of magnitude,and the expansion modulus of oil/water interface was increased by 77% at equilibrium.In addition,the solid surface roughness was reduced by 50%,and the three-phase contact angle dropped from 135(oil-wet)to 48(water-wet).Combining the displacement experiments using a 2.5D reservoir micromodel and a microchannel model,the remaining oil mobilization and migration processes in micro-to nano-scale pores and throats were visualized.It was found that the nanofluid dispersed the remaining oil into small oil droplets and displaced them via multiple mechanisms in porous media.Moreover,the high strength interface film formed by the nanofluid inhibited the coalescence of oil droplets and improved the flowing ability.These results help to understand the EOR mechanisms of nanofluids in low permeability reservoirs from a visual perspective.

Sliding Mode Control Approach with Integrated Disturbance Observer for PMSM Speed System

The research on high-performance vector control of permanent magnet synchronous motor(PMSM)drive system plays an extremely important role in electrical drive system.To further improve the speed control performance of the system,a fast non-singular end sliding mode(FNTSM)surface function based on traditional NTSM control is developed.The theoretical analysis proves that the FNTSM surface function has a faster dynamic response and more finite-time convergence.In addition,for the self-vibration problem caused by high sliding mode switching gain,an FNTSM control method with anti-disturbance capability was designed based on the linear disturbance observer(DO),i.e.the FNTSMDO method was employed to devise the PMSM speed regulator.The comparative simulation and experiment results with traditional PI control and NTSM control methods indicate that the FNTSMDO method could improve the dynamic performance and anti-interference of the system.

Corrigendum to:“Spectrum-tailored random fiber laser towards ICF laser facility”[Matter and Radiation at Extremes 8,025902(2023)]

The third paragraph in Sec.IV REGENERATIVE AMPLIFICATION erroneously states“In other words,the distribution of spectral components is time-dependent,and the spectral distortion in the amplification process will not change the time-domain shape.”

Potential application of let-7a antagomir in injured peripheral nerve regeneration

Neurotrophic factors,particularly nerve growth factor,enhance neuronal regeneration.However,the in vivo applications of nerve growth factor are largely limited by its intrinsic disadvantages,such as its short biological half-life,its contribution to pain response,and its inability to cross the blood-brain barrier.Considering that let-7(human miRNA)targets and regulates nerve growth factor,and that let-7 is a core regulator in peripheral nerve regeneration,we evaluated the possibilities of let-7 application in nerve repair.In this study,anti-let-7a was identified as the most suitable let-7 family molecule by analyses of endogenous expression and regulatory relationship,and functional screening.Let-7a antagomir demonstrated biosafety based on the results of in vivo safety assessments and it entered into the main cell types of the sciatic nerve,including Schwann cells,fibroblasts and macrophages.Use of hydrogel effectively achieved controlled,localized,and sustained delivery of let-7a antagomir.Finally,let-7a antagomir was integrated into chitosan conduit to construct a chitosan-hydrogel scaffold tissue-engineered nerve graft,which promoted nerve regeneration and functional recovery in a rat model of sciatic nerve transection.Our study provides an experimental basis for potential in vivo application of let-7a.

A rate-dependent constitutive model for saturated frozen soil considering local breakage mechanism

A rate-dependent constitutive model for saturated frozen soil is vital in frozen soil mechanics,especially when simultaneously describing the nonlinearity,dilatancy and strain-softening characteristics.The distribution of the non-uniform strain rate of saturated frozen soil at the meso-scale due to the local icecementation breakage is described by a newly binary-medium-based homogenization equation.Based on the field-equation-based approach of the meso-mechanics theory,the interaction expression of the strain rate at macro-and meso-scale is derived,which can give the strain rate concentration tensor at different crushed degrees.With the thermodynamics and empirical assumption,a breakage ratio in the rate-dependent form is determined.This overcomes the limitations of the existing binary-medium-based models that are difficult to simulate rate-dependent mechanical response.Based on these assumptions,a newly binary-medium-based rate-dependent model is proposed considering both the ice bond breakage and material composition characteristics of saturated frozen soil.The proposed constitutive model has been validated by the test results on frozen soils with different temperatures and strain rates.

Effects of magnesium and copper additions on tensile properties of Al-Si-Cr die casting alloy under as-cast and T5 conditions

Aluminum high pressure die casting(HPDC)technology has evolved in the past decades,enabling stronger and larger one-piece casting with significant part consolidation.It also offers a higher design freedom for more mass-efficient thin-walled body structures.For body structures that require excellent ductility and fracture toughness to be joined with steel sheet via self-piercing riveting(for instance,shock towers and hinge pillars,etc.),a costly T7 heat treatment comprising a solution heat treatment at elevated temperatures(450℃-500℃)followed by an over-ageing heat treatment is needed to optimize microstructure for meeting product requirement.To enable cost-efficient mass production of HPDC body structures,it is important to eliminate the expensive T7 heat treatment without sacrificing mechanical properties.Optimizing die cast alloy chemistry is a potential solution to improve fracture toughness and ductility of the HPDC components.The present study intends to tailor the Mg and Cu additions for a new Al-Si-Cr type die casting alloy(registered as A379 with The Aluminum Association,USA)to achieve the desired tensile properties without using T7 heat treatment.It was found that Cu addition should be avoided,as it is not effective in enhancing strength while degrades tensile ductility.Mg addition is very effective in improving strength and has minor impact on tensile ductility.The investigated Al-Si-Cr alloy with a nominal composition of Al-8.5wt.%Si-0.3wt.%Cr-0.2wt.%Fe shows comparable tensile properties with the T7 treated AlSi10MnMg alloy which is currently used for manufacturing shock towers and hinge pillars.

Growth differentiation factor 15 predicts cardiovascular events in stable coronary artery disease

BACKGROUND Growth differentiation factor 15(GDF-15)has been explored as a potential biomarker for various inflammatory diseases and cardiovascular events.This study aimed to assess the predictive role of GDF-15 levels in cardiovascular events and all-cause mortality,considering traditional risk factors and other biomarkers.METHODS A prospective study was conducted and 3699 patients with stable coronary artery disease(CAD)were enrolled into the research.Baseline GDF-15 levels were measured.Median follow-up was 3.1 years during the study.We analyzed clinical variables and several biomarkers.Multivariable Cox regression analysis was performed to evaluate prognostic performance of GDF-15 levels in predicting myocardial infarction(MI),heart failure,stroke,cardiovascular death,and non-cardiovascular death.RESULTS Baseline GDF-15 levels for 3699 patients were grouped by quartile(≤1153,1153-1888,1888-3043,>3043 ng/L).Higher GDF-15 levels were associated with older age,male gender,history of hypertension,and elevated levels of N-terminal pro Btype natriuretic peptide(NT-pro BNP),soluble suppression of tumorigenesis-2(sST2),and creatine(each with P<0.001).Adjusting for established risk factors and biomarkers in Cox proportional hazards models,a 1 standard deviation(SD)increase in GDF-15 was associated with elevated risk of clinical events[hazard ratio(HR)=2.18,95%confidence interval(CI):(1.52-3.11)],including:MI[HR=2.8395%CI:(1.03-7.74)],heart failure[HR=2.7195%CI:(1.18-6.23)],cardiovascular and non-cardiovascular death[HR=2.48,95%CI(1.49-4.11)]during the median follow up of 3.1 years.CONCLUSIONS Higher levels of GDF-15 consistently provides prognostic information for cardiovascular events and all cause death,independent of clinical risk factors and other biomarkers.GDF-15 could be considered as a valuable addition to future risk prediction model in secondary prevention for predicting clinical events in patient with stable CAD.

Spectrum-tailored random fiber laser towards ICF laser facility

Broadband low-coherence light is considered to be an effective way to suppress laser plasma instability.Recent studies have demonstrated the ability of low-coherence laser facilities to reduce back-scattering during beam–target coupling.However,to ensure simultaneous low coherence and high energy,complex spectral modulation methods and amplification routes have to be adopted.In this work,we propose the use of a random fiber laser(RFL)as the seed source.The spectral features of this RFL can be carefully tailored to provide a good match with the gain characteristics of the laser amplification medium,thus enabling efficient amplification while maintaining low coherence.First,a theoretical model is constructed to give a comprehensive description of the output characteristics of the spectrum-tailored RFL,after which the designed RFL is experimentally realized as a seed source.Through precise pulse shaping and efficient regenerative amplification,a shaped random laser pulse output of 28 mJ is obtained,which is the first random laser system with megawatt-class peak power that is able to achieve low coherence and efficient spectrum-conformal regenerative amplification.

Preparation of bowl-shaped polydopamine surface imprinted polymer composite adsorbent for specific separation of 2'-deoxyadenosine

Molecularly imprinted polymers (MIPs) have great potential as adsorbents for selective adsorption and separation of nucleoside compounds,but effectively enhancing the affinity of recognition sites by adjusting the forces between template molecules and functional monomers remains an important challenge.In this work,a surface imprinting strategy was used to construct bowl-shaped molecularly imprinted composite sorbents (BHPN@MIPs) based on polydopamine (PDA) particles and have achieved selective separation and purification of 2'-deoxyadenosine (dA).Where by the base complementary pairing interaction of the combined template molecule d A and the pyrimidine functional monomer can enhance the preassembly force,and the hydrophilic bowl-shaped PDA can provide a larger storage space contact efficiency of d A in the test solution,causing the site utilization much higher and improving the kinetic adsorption performance.The equilibrium adsorption time and maximum adsorption capacity of60 min and 328.45μmol·g^(-1)were observed by static adsorption experiments,and the selectivity experimental results showed an imprinting factor IF of 1.30.After four adsorption–desorption cycles,the initial adsorption equilibrium adsorption capacity of BHPN@MIPs still retained 91.14%.By evaluating the selective adsorption of d A in spiked human serum solutions,BHPN@MIPs can be used to selectively enrich and analyze target d A in complex biological samples.

Multi-channel generation of vortex beams with controllable polarization states and orbital angular momentum

Optical vortices with tunable polarization states and topological charges are widely investigated in various physical systems and practical devices for high-capacity optical communication.However,this kind of structured light beams is usually generated using several polarization and spatial phase devices,which decreases the configurability of optical systems.Here,we have designed a kind of polarized optical multi-vortices generator based on the Stokes-Mueller formalism and cross-phase modulation.In our scheme,multi-channel generation of polarized vortex beams can be realized through a single optical element and a single-input Gaussian beam.The polarization states and orbital angular momentum of the generated light beams are all-optically controllable.Furthermore,the proposed polarized optical multi-vortices generator has also been demonstrated experimentally through one-step holographic recording in an azobenzene liquid-crystalline film and the experimental results agree with theoretical analysis.