Selection of reductants for extracting selenium and tellurium from degoldized solution of copper anode slimes

This paper focused on investigating high-efficient reductants of recovering selenium and tellurium from degoldizedsolution of copper anode slimes.Firstly,the effect of various reductants on recovery rates of Se and Te was investigated based onthermodynamic analysis of various metallic ions in degoldized solution.Secondly,the single factor experiments were made toinvestigate the effect of the process parameters on recovering Se and Te with hydrazine hydrate.Finally,the hydroxylaminehydrochloride was added to intensify the extraction efficiencies of Se and Te.The results indicated that hydrazine hydrate was themost suitable reductant,and the recovery rates of Se and Te are71.23%and76.50%,respectively;the recovery rates of Se and Tewere92.07%and97.81%,respectively,under the optimal process conditions of hydrazine hydrate dosage of0.2133mol/L,H+concentration of4.305mol/L,reaction temperature of85°C and reaction time of5h;the recovery rate of Se was97.59%,and that Tereached up to100%when hydroxylamine hydrochloride dosage was1.5116mol/L.

Process mineralogy characteristics of acid leaching residue produced in low-temperature roasting-acid leaching pretreatment process of refractory gold concentrates

To provide a theoretical basis for a suitable process to extract gold from refractory gold concentrates, process mineralogy on the acid leaching residue of gold calcine was studied by chemical composition, X-ray diffraction, scanning electron microscopy-energy spectrum, and mineral dissociation analysis. The results showed that the acid leaching residue contained Au 68.22 g/t, Ag 92.71 g/t, Fe 0.44%, As 0.10%, and S 0.55%. Gold and silver minerals existed as native gold, argentite, and proustite. Quartz, the main gangue mineral, accounted for 78.33 wt/%. The dissociation degree analysis showed that the proportions of monomer and exposed gold in acid leaching residue were 96.66 wt%. The cyanidation results showed that the cyanide gold leaching rate of acid leaching residues was close to 100 wt%. However, the maximum cyanide gold leaching rate of gold calcine was only 85.31 wt%. This suggests that acid leaching can increase the gold dissolution rate in the cyanide process.

Differences of cyanide leaching between calcine and dust from refractory gold concentrates

Differences of cyanide leaching between the calcine and the dust from a refractory gold concentrate were investigated by comparative method. Results showed that gold leaching efficiencies of the calcine and the dust were 85.31% and 54.30%, respectively, with direct cyanidation. Contents and existing forms of arsenic and carbon were the main reasons for those differences. The maximum gold leaching efficiencies of the calcine and the dust were 87.70% and 58.60%, respectively, with cyanidation after NaOH pre-leaching. Harmful elements removal, gold loss in NaOH pre-leaching and iron oxides hindrance codetermined gold leaching efficiencies of the calcine and the dust. After H2SO4 pre-leaching, the maximum gold leaching efficiencies of the calcine and the dust achieved 94.96% and 80.40%, respectively. The effect of carbonaceous matter was the main reason for differences for leaching efficiencies of the calcine and the dust. Based on those differences, two proper gold extraction processes were put forward, and gold leaching efficiencies for the calcine and the dust achieved 94.91% and 91.90%, respectively.

Deselenization and detellurization of precious-metal ore concentrates by swelling oxidizing roasting and successive alkaline leaching

A new technique of swelling oxidizing roasting and alkaline leaching was proposed for deselenization and detellurization of pre- cious-metal ore concentrates. Alkali-metal and alkaline-earth-metal chlorides and carbonates were preliminarily selected as swelling agents. The roasting removal rate and alkaline leaching rate of selenium and tellurium were investigated, and NaCl was selected as an appropriate swelling agent. Furthermore, the effects of various factors on the selenium gasification rate and leaching rate of selenium and tellurium were investigated. The results show that the selenium gasification rate reaches 88.41% after swelling oxidizing roasting for 2 h at 510~C using an NaC1 dosage coefficient of 100 and a sulfuric acid dosage coefficient of 1.3; the amorphous elemental tellurium is completely transformed into TeO2. The roasted product is subjected to alkaline leaching using a 100 g/L NaOH solution, which results in a selenium leaching rate of 10.51%, a total selenium removal rate of 98.92%, and a tellurium leaching rate of 97.64%. In the alkaline leaching residue, the contents of selenium, tellurium, gold, platinum, and palladium are 0.7825%, 5.492%, 8.333%, 0.2587%, and 1.113%, respectively; the precious metals are enriched approximately sixfold.

Recovery of magnetite from waste ferrous sulfate using polyethylene glycol(PEG) as a dispersant

The effect of PEG dispersant on the magnetic separation of magnetite（Fe3O4） synthesized from ferrous sulfate solution via co-precipitation method with calcium hydroxide as the precipitant was investigated. The results indicated that a PEG dispersant could significantly affect Fe3O4 recovery. Adding PEG during the preparation of Fe3O4 was unfavorable for Fe3O4 recovery. When the PEG-6000 concentration was increased from 0 to 8 g/L, the iron grade and median particle size of the Fe3O4 product decreased from 65.58% and 2.35 μm to 57.79% and 1.35 μm, respectively. However, adding PEG during the wet milling of the mixed product promoted the subsequent recovery of Fe3O4. When the amount of PEG-200 increased from 0% to 4% of the powder mass, the grade of iron in the Fe3O4 product increased from 65.58% to 68.32%. While the relative molecular mass of PEG at an amount of 4% of the powder mass increased from 200 to 20000, the grade of iron was reduced from 68.32% to 66.70%.

Al_(x)/HKUST-1 prepared by synthetic exchange as catalyst for reduction of NO by CO at low temperature

Al_(x)/HKUST-1(x=1/24,1/12,1/6,1/3),one of the bimetallic copper-based organic framework materials,was successfully prepared by the synthetic exchange method and characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM),specific surface area(BET),thermogravimetric analysis(TG),infrared spectra(IR),X-ray photoelectron spectroscopy(XPS),and H_(2)-temperature programmed reduction(H_(2)-TPR).The findings indicated that Al_(x)/HKUST-1 maintained the octahedral morphology of its precursor(HKUST-1).The thermal stability and catalytic reduction ability of HKUST-1 skeleton were improved by doping aluminum(Al^(3+)).Al_(1/12)/HKUST-1 showed the best performance among all samples,with a nitric oxide(NO)conversion rate of 100%at 210℃(50℃lower than that of HKUST-1).The valence kind of Al,Cu,and O in Al_(1/12)/HKUST-1 did not change after the catalytic reaction,but the contents of Al,Cu,and O in different forms changed significantly.The catalytic process of the Al_(x)/HKUST-1 followed a Langmuir-Hinshelwood mechanism.

A new diagnostic model of primary open angle glaucoma based on FD-OCT parameters

AIM： To build a clinical diagnostic model of primary open angle glaucoma （POAG） using the normal probability chart of frequency-domain optical coherence tomography （FD-OCT）. METHODS： This is a cross-sectional study. Total 133 eyes from 133 healthy subjects and 99 eyes from 99 early POAG patients were included in the study. The retinal nerve fibre layer （RNFL） thickness parameters of optic nerve head （ONH） and RNFL3.45 scan were measured in one randomly selected eye of each subject using RTVue-100 FD-OCT. Then, we used these parameters to establish the diagnostic models. Four different diagnostic models based on two different area partition strategies on ONH and RNFL3.45 parameters, including ONH traditional area partition model （ONH-T）, ONH new area partition model （ONH-N）, RNFL3.45 traditional area partition model （RNFL3.45-T） and RNFL3.45 new area partition model （RNFL3.45-N）, were built and tested by cross-validation. RESULTS： The new area partition models had higher area under the receiver operating characteristic （AROC; ONH-N： 0.990; RNFL3.45-N： 0.939） than corresponding traditional area partition models （ONH-T： 0.979; RNFL3.45-T： 0.881）. There was no statistical difference among AROC of ONH-T, ONH-N, and RNFL3.45-N. Nevertheless, ONH-N was the simplest model. CONCLUSION： The new area partition models had higher diagnostic accuracy than corresponding traditional area partition models, which can improve the diagnostic ability of early POAG. In particular, the simplest ONH-N diagnostic model may be convenient for clinical application.

Effect of purification pretreatment on the recovery of magnetite from waste ferrous sulfate

The present study was conducted to elucidate the influence of impurities in waste ferrous sulfate on its recovery of magnetite. Ferrous sulfate solution was purified by the addition of Na OH solution to precipitate impurities, and magnetite was recovered from ferrous sulfate solution without and with purification pretreatment. Calcium hydroxide was added to the solution of ferrous sulfate as a precipitator. A mixed product of magnetite and gypsum was subsequently obtained by air oxidation and heating. Wet-milling was performed prior to magnetic separation to recover magnetite from the mixed products. The results show that with the purification pretreatment, the grade of iron in magnetite concentrate increased from 62.05% to 65.58% and the recovery rate of iron decreased from 85.35% to 80.35%. The purification pretreatment reduced the conglutination between magnetite and gypsum, which favors their subsequent magnetic separation. In summary, a higher-grade magnetite with a better crystallinity and a larger particle size of 2.35 μm was obtained with the purification pretreatment.

Dermoscopy in China: current status and future prospective

Objective: Dermoscopy is a useful technique for improving the diagnostic accuracy of various types of skin disorders. In China, dermoscopy has been widely accepted, and domestic researchers have made tremendous progress in the field of dermoscopy. The main purpose of this review is to summarize the current status of dermoscopy in China and identify its future directions. Data sources: Articles included in this review were obtained by searching the following databases: Wanfang, China National Knowledge Infrastructure, PubMed, and the Web of Science. We focused on research published before 2019 with keywords including dermoscopy, dermoscopic, dermoscope and trichoscopy. Study selection: A total of 50 studies were selected. Of these studies, 20 studies were in Chinese and 30 in English, research samples of all the studies were collected from Chinese populations. Results: Since 2000, more than 380 articles about dermoscopy have been published in domestic or foreign journals. Dermoscopy can improve the diagnostic accuracy of neoplastic diseases, evaluating the therapeutic effect of treatment, and determining the treatment endpoint, and it can also assist in the differential diagnosis of inflammatory diseases and in the assessment of the severity of the disease. In addition, researches about the applications of dermoscopy during surgical treatment have been published. Training courses aiming to improve the diagnostic ability of dermatologists, either face-to-face or online, have been offered. The Chinese Skin Image Database, launched in 2017 as a work platform for dermatologists, has promoted the development of dermoscopy in China. Computer-aided diagnostic systems based on the Chinese population are ready for use. In the future, cooperation, resource sharing, talent development, image management, and computer-aided diagnosis will be important directions for the development of dermoscopy in China. Conclusion: Dermoscopy has been widely used and developed in China, however, it still needs to address more challenges in the future.

Preparation of high-purity tellurium powder by hydrometallurgical method

This hydrometallurgical method consists of oxidation leaching, sulfide impurities removing, and sulfur dioxide reduction. The crude tellurium powder was treated by H2Oa oxidation for 2.0 h at pH 2.5 when adding 50 ml H2O2 （30 %） per 100 g raw material, a tellurium recover rate around 91% is achieved. The tellurium leaching ratio can reach 98.9 % under 3.75 mol.L-1 NaOH concentration in liquid-solid ratio of 5：1 at 80 ℃ for 1.5 h. The overall separation of tellurium and other heavy metals is optimum at sulfide dosages of about 1.1 times of the theoretical values. The removal rates of Ag, Ni, Pb, and Cu from the solution are greater than 99.8 %, and As and Se removal rates are 98.6 % and 97.2 %, respectively. Over 99.5 % tellurium can be recovered by SOu reaction when the operation is conducted at 85 ℃ in 6 mol.L-1 HC1 solution. The tellurium powder with size of 〈5 μm and purity of 〉99.999 % is obtained.

RNA-seq analysis of molecular heterogeneity peripheral blood mononuclear cells in systemic lupus erythematosus

Systemic lupus erythematosus(SLE)is an autoimmune disease characterized by a broad spectrum of clinical manifestations.Although great progress has been made in understanding the contribution of genetic and environmental factors in SLE pathogenesis,as there are over 20,000 published studies evaluating related cellular dysfunction,111 the exact mechanisms that underline this process are still unknown.Over the past 10 years,novel insights have mainly originated from genome-wide association(GWAS)and gene expression studies.