A comprehensive review on microchannel heat sinks for electronics cooling

The heat generation of electronic devices is increasing dramatically,which causes a serious bottleneck in the thermal management of electronics,and overheating will result in performance deterioration and even device damage.With the development of micro-machining technologies,the microchannel heat sink(MCHS)has become one of the best ways to remove the considerable amount of heat generated by high-power electronics.It has the advantages of large specific surface area,small size,coolant saving and high heat transfer coefficient.This paper comprehensively takes an overview of the research progress in MCHSs and generalizes the hotspots and bottlenecks of this area.The heat transfer mechanisms and performances of different channel structures,coolants,channel materials and some other influencing factors are reviewed.Additionally,this paper classifies the heat transfer enhancement technology and reviews the related studies on both the single-phase and phase-change flow and heat transfer.The comprehensive review is expected to provide a theoretical reference and technical guidance for further research and application of MCHSs in the future.

Optimization of extrusion process parameters of Incoloy028 alloy based on hot compression test and simulation

True stress?true strain curves of Incoloy028alloy at high temperature and strain rate were investigated by hot compression test.These curves show that the maximum flow stress decreases with the increase in temperature and the decrease in strain rate.FEM simulation was employed to investigate the influence of temperature,extrusion speed and friction coefficient on the extrusion load,stress,strain and strain rate in the extrusion process.The increase of extrusion temperature results in decrease of load and deformation resistance,but has little influence on strain and strain rate.When extrusion speed changes between200and350mm/s,no obvious change about extrusion load can be found.Sharp peak value up to42500kN emerges in the extrusion load curve and the extrusion process becomes unstable seriously when extrusion speed rises up to400mm/s.Both stress and strain rate increase with the raise of extrusion speed.When friction coefficient is between0.02and0.03,deformation resistance is about160MPa and the strain rate can be limited below70s?1.Successful production of Incoloy028tube verifies the optimized parameters by FEM simulation analysis,and mechanical tests results of the products meet the required properties.

Ionizable drug delivery systems for efficient and selective gene therapy

Gene therapy has shown great potential to treat various diseases by repairing the abnormal gene function.However,a great challenge in bringing the nucleic acid formulations to the market is the safe and effective delivery to the specific tissues and cells.To be excited,the development of ionizable drug delivery systems(IDDSs)has promoted a great breakthrough as evidenced by the approval of the BNT162b2 vaccine for prevention of coronavirus disease 2019(COVID-19)in 2021.Compared with conventional cationic gene vectors,IDDSs can decrease the toxicity of carriers to cell membranes,and increase cellular uptake and endosomal escape of nucleic acids by their unique pH-responsive structures.Despite the progress,there remain necessary requirements for designing more efficient IDDSs for precise gene therapy.Herein,we systematically classify the IDDSs and summarize the characteristics and advantages of IDDSs in order to explore the underlying design mechanisms.The delivery mechanisms and therapeutic applications of IDDSs are comprehensively reviewed for the delivery of plasmid DNA(pDNA)and four kinds of RNA.In particular,organ selecting considerations and high-throughput screening are highlighted to explore efficiently multifunctional ionizable nanomaterials with superior gene delivery capacity.We anticipate providing references for researchers to rationally design more efficient and accurate targeted gene delivery systems in the future,and indicate ideas for developing next generation gene vectors.

Cap morphology after small-incision lenticule extraction and its effects on intraocular scattering

AIM： To investigate cap morphology after small-incision lenticule extraction （SMILE） and its effects on intraocular scattering. METHODS： Sixty-five eyes of 33 patients undergoing SMILE were enrolled. In addition to regular evaluation, Fourier-domain optical coherence tomography was used to investigate cap thickness at ld, lwk, 1 and 3mo postoperatively. The optical quality including modulation transfer function cutoff frequency, Strehl ratio, Optical Quality Analysis System （OQAS） values, and objective scattering index （OSI）, were evaluated using OQASTM. RESULTS： Cap thickness decreased from ld to lwk （P〈0.001）, but remained higher than intended thickness of 120 μm after 3mo （P〈0.001）. Cap thickness in central area was thinner than that of in the paracentral and peripheral areas （P〈0.0001）. Total number of microdistortions decreased from ld to 3mo （P〈0.0001）. Pearson analysis revealed a weak correlation between OSI and standard deviation of cap thickness at ld and lmo, as well as between range of cap thickness and OSI at 1mo. No correlation was found between microdistortion and OSI, but a negative correlation existed between microdistortion and range at ld and lmoafter surgery. CONCLUSION： The corneal cap tends to be more accurate and regular with time lapse. Better cap morphology tends to contribute less intraocular scattering in the eyes undergoing SMILE.

Experimental study on jet pulse assembly design and numerical simulation

Jet pulse assembly is one of the main components of jet hydraulic oscillator.The pressure wave characteristics produced by jet pulse assembly have an important influence on the performance of the tool.In this paper,the structure and working principle of jet pulse assembly are studied,the mechanical analysis model of piston rod is established,the dynamic resistance ratio formula of jet pulse assembly is deduced,and the numerical simulation test of 89-mm jet pulse assembly structure parameters is carried out.The results show that the piston rod downward stroke is driven by both the jet element driving force and the throttle plate load driving force,and can stably descend.The driving force of the piston rod upward stroke jet element is opposite to the load acting force of the throttle disc,and the jet driving force needs to be greater than the load resistance of the throttle disc to stably ascend.The dynamic resistance ratio formula is deduced.When the area of the end of the piston rod is reduced,the resistance of the throttle disc is reduced and the jet power is increased,thus solving the problem of insufficient power of the piston rod in the upstroke and ensuring the normal operation of the tool.Ten groups of numerical simulation tests were carried out,and it was found that the pressure amplitude and pressure drop of the tool decreased significantly with the increase of the tool size,and the error between the numerical simulation value and the theoretical calculation value was less than 9%,which verified the correctness of the theory.It is suggested to select tools on site according to the drilling construction situation to ensure the drilling effect.

Extrusion process of 304L H-shaped stainless steel used in passive residual heat removal heat exchanger

304L H-shaped stainless steel is used as the support frame of the passive residual heat removal heat exchanger(PRHR HX) in a nuclear fission reactor. The extrusion process is adopted to manufacture the 304L H-shaped stainless steel. Finite element method simulation is herein used to analyze metal flow characteristics, optimize the extrusion die, and predict the extrusion force at different temperatures and speeds. A Φ400-mm container and Φ388-mm forging billet are selected, and the 304L H-shaped stainless steel is successfully manufactured using a Germany SMS 60 MN horizontal extruder. The mechanical properties and microstructure of the manufactured 304L H-shaped stainless steel meet the requirements of the PRHR HX, and the surfaces of the product pass the dye penetration test. The H-shaped stainless steels are used in Haiyang nuclear power plant in Shandong Province.