A series of spinel-type Mg_(0.25-x)Al_(2.57)O_(3.79)N_(0.21):xMn^(2+)(MgAlON:xMn^(2+))phosphors were synthesized by the solid-state reaction route.The transparent ceramic phosphors were fabricated by pressureless sint...A series of spinel-type Mg_(0.25-x)Al_(2.57)O_(3.79)N_(0.21):xMn^(2+)(MgAlON:xMn^(2+))phosphors were synthesized by the solid-state reaction route.The transparent ceramic phosphors were fabricated by pressureless sintering followed by hot-isostatic pressing(HIP).The crystal structure,luminescence and mechanical properties of the samples were systematically investigated.The transparent ceramic phosphors with tetrahedrally coordinated Mn^(2+)show strong green emission centered around 515 nm under blue light excitation.As the Mn^(2+)concentration increases,the crystal lattice expands slightly,resulting in a variation of crystal field and a slight red-shift of green emission peak.Six weak absorption peaks in the transmittance spectra originate from the spin-forbidden ^(4)T_(1)(^(4)G)→^(6)A_(1) transition of Mn^(2+).The decay time was found to decrease from 5.66 to 5.16 ms with the Mn^(2+)concentration.The present study contributes to the systematic understanding of crystal structure and properties of MgAlON:xMn^(2+)green-emitting transparent ceramic phosphor which has a potential application in high-power light-emitting diodes.展开更多
Continuous oxide fiber/oxide matrix composites are attractive for use as high temperature structural materials. As SiO2 has good ablation-resistant property and high temperature dielectric property, it is an ideal pro...Continuous oxide fiber/oxide matrix composites are attractive for use as high temperature structural materials. As SiO2 has good ablation-resistant property and high temperature dielectric property, it is an ideal protective material for missile and antenna window. At present, 3D SiO2 matrix composites reinforced by silica fibers and high Si-O fibers are manufactured by impregnating the preform in colloidal aqueous silica sol repeatedly and then by sintering; C fiber reinforced SiO2 matrix composites are processed by infiltration of silica slurry and then hot-pressing. It is well known that CVI （Chemical Vapor Infiltration） is a near-net-shape and flexible process, which can be applied to preforms of complex and different shape. However, to our best knowledge, CVI has not been used to manufacture fiber-reinforced SiO2 matrix composites. In this article, APCVI （Atmospheric Pressure Chemical Vapor Infiltration） was used to manufacture Nextel 480/silica composites. The Nextel 480 fiber is a boria rich mullite composition containing 70wt%alumina, SiO228wt%silica, and 2wt%boria. TEOS （Tetra ethyl ortho silicate） was used as precursor. Argon was used as carrier gas. The phases were detected by X-ray diffractometer （XRD, Rigaku D/MAX-3C）. The microstructures were examined by scanning electron microscopy （SEM, JEOL JXA-840）. Fig.1 shows the relation of deposition rate versus deposition temperature for two different diameters of deposition furnace. The deposition rate was determined by weighing the samples before and after deposition. The results indicate that the deposition rate of silica increases with increasing temperature in the range of 400～750℃ and decreases with increasing temperature in the range of 750850℃. We found that the sample deposited at 750℃ had a smooth surface and the single filament fiber was clearly seen by SEM （Fig.2（a））. But the surface of another sample deposited at 800℃ was rough due to the piling up of SiO2 powder, which was very weakly bonded with the fiber preform and dropped easily even when lightly touched （Fig.2（b））. The transitional products of TEOS at 750℃ are liquid phase, which adheres to the fiber surface and keeps on decomposing to form the core of silica and ultimately solid silica results. Both the surface of the transitional liquid phase products and the fiber surfaces are well wetted, the bonding among silica particles formed after complete decomposition is strong and the silica surface is homogeneous and smooth. When the deposition temperature is 800℃, the solid silica is formed directly from vapor phase; the piling up of SiO2 powders on the surface of the preform made it very difficult for subsequent vapor to infiltrate and caused low deposition rate. The relatively lower temperature of 750℃ is the key in CVI processing. Fig.1 shows that the deposition rate is also dramatically affected by the inner diameter of deposition reactor. When the inner diameter decreases, the deposition rate increases, other deposition conditions being the same. The deposition rate in 12 mm-inner-diameter reactor is twice as high as that in 17 mm-inner-diameter reactor at 750℃. It indicates that the deposition process is controlled by mass transfer, which can create homogeneous and smooth film and is beneficial to fabricating fiber-reinforced silica matrix composites. Fig.3 shows the microstructure of the cross-sectional surface of the composites fabricated under the following conditions: carrier gas 400ml/min, TEOS 50℃, deposition temperature 750℃ and deposition time 60h. The silica coating is about 2.4 μm in thickness and the deposition rate is about 0.04μm per hour. It is found that each fiber is surrounded homogeneously by silica matrix and there are no cracks on the surface of the silica matrix. It indicates that good thermal match exists between the Nextel 480 fibers and silica matrix and that consequently high temperature or thermal shock produces only very small thermal stresses in the as-fabricated composites; thus life of the composites is prolonged. Fig.4 shows the XRD展开更多
基金Funded by the National Natural Science Foundation of China(No.52272072)the Independent Innovation Projects of the Hubei Longzhong Laboratory(No.2022ZZ-13)。
文摘A series of spinel-type Mg_(0.25-x)Al_(2.57)O_(3.79)N_(0.21):xMn^(2+)(MgAlON:xMn^(2+))phosphors were synthesized by the solid-state reaction route.The transparent ceramic phosphors were fabricated by pressureless sintering followed by hot-isostatic pressing(HIP).The crystal structure,luminescence and mechanical properties of the samples were systematically investigated.The transparent ceramic phosphors with tetrahedrally coordinated Mn^(2+)show strong green emission centered around 515 nm under blue light excitation.As the Mn^(2+)concentration increases,the crystal lattice expands slightly,resulting in a variation of crystal field and a slight red-shift of green emission peak.Six weak absorption peaks in the transmittance spectra originate from the spin-forbidden ^(4)T_(1)(^(4)G)→^(6)A_(1) transition of Mn^(2+).The decay time was found to decrease from 5.66 to 5.16 ms with the Mn^(2+)concentration.The present study contributes to the systematic understanding of crystal structure and properties of MgAlON:xMn^(2+)green-emitting transparent ceramic phosphor which has a potential application in high-power light-emitting diodes.
文摘Continuous oxide fiber/oxide matrix composites are attractive for use as high temperature structural materials. As SiO2 has good ablation-resistant property and high temperature dielectric property, it is an ideal protective material for missile and antenna window. At present, 3D SiO2 matrix composites reinforced by silica fibers and high Si-O fibers are manufactured by impregnating the preform in colloidal aqueous silica sol repeatedly and then by sintering; C fiber reinforced SiO2 matrix composites are processed by infiltration of silica slurry and then hot-pressing. It is well known that CVI （Chemical Vapor Infiltration） is a near-net-shape and flexible process, which can be applied to preforms of complex and different shape. However, to our best knowledge, CVI has not been used to manufacture fiber-reinforced SiO2 matrix composites. In this article, APCVI （Atmospheric Pressure Chemical Vapor Infiltration） was used to manufacture Nextel 480/silica composites. The Nextel 480 fiber is a boria rich mullite composition containing 70wt%alumina, SiO228wt%silica, and 2wt%boria. TEOS （Tetra ethyl ortho silicate） was used as precursor. Argon was used as carrier gas. The phases were detected by X-ray diffractometer （XRD, Rigaku D/MAX-3C）. The microstructures were examined by scanning electron microscopy （SEM, JEOL JXA-840）. Fig.1 shows the relation of deposition rate versus deposition temperature for two different diameters of deposition furnace. The deposition rate was determined by weighing the samples before and after deposition. The results indicate that the deposition rate of silica increases with increasing temperature in the range of 400～750℃ and decreases with increasing temperature in the range of 750850℃. We found that the sample deposited at 750℃ had a smooth surface and the single filament fiber was clearly seen by SEM （Fig.2（a））. But the surface of another sample deposited at 800℃ was rough due to the piling up of SiO2 powder, which was very weakly bonded with the fiber preform and dropped easily even when lightly touched （Fig.2（b））. The transitional products of TEOS at 750℃ are liquid phase, which adheres to the fiber surface and keeps on decomposing to form the core of silica and ultimately solid silica results. Both the surface of the transitional liquid phase products and the fiber surfaces are well wetted, the bonding among silica particles formed after complete decomposition is strong and the silica surface is homogeneous and smooth. When the deposition temperature is 800℃, the solid silica is formed directly from vapor phase; the piling up of SiO2 powders on the surface of the preform made it very difficult for subsequent vapor to infiltrate and caused low deposition rate. The relatively lower temperature of 750℃ is the key in CVI processing. Fig.1 shows that the deposition rate is also dramatically affected by the inner diameter of deposition reactor. When the inner diameter decreases, the deposition rate increases, other deposition conditions being the same. The deposition rate in 12 mm-inner-diameter reactor is twice as high as that in 17 mm-inner-diameter reactor at 750℃. It indicates that the deposition process is controlled by mass transfer, which can create homogeneous and smooth film and is beneficial to fabricating fiber-reinforced silica matrix composites. Fig.3 shows the microstructure of the cross-sectional surface of the composites fabricated under the following conditions: carrier gas 400ml/min, TEOS 50℃, deposition temperature 750℃ and deposition time 60h. The silica coating is about 2.4 μm in thickness and the deposition rate is about 0.04μm per hour. It is found that each fiber is surrounded homogeneously by silica matrix and there are no cracks on the surface of the silica matrix. It indicates that good thermal match exists between the Nextel 480 fibers and silica matrix and that consequently high temperature or thermal shock produces only very small thermal stresses in the as-fabricated composites; thus life of the composites is prolonged. Fig.4 shows the XRD
