Effect of Al content on the reaction between Fe-10Mn-xAl(x=0.035wt%,0.5wt%,1wt%,and 2wt%)steel and CaO-SiO_(2)-Al_(2)O_(3)-MgO slag

The effect of Al content(0.035 wt%,0.5 wt%,1 wt%,and 2 wt%)on the composition change of steel and slag as well as inclusion transformation of high manganese steel after it has equilibrated with Ca O-Si O_(2)-Al_(2)O_(3)-Mg O slag was studied using the method of slag/steel reaction.The experimental results showed that as the initial content of Al increased from 0.035 wt%to 2 wt%,Al gradually replaced Mn to react with Si O_(2)in slag to avoid the loss of Mn due to the reaction;this process caused both Al_(2)O_(3)in slag and Si in steel to increase while Si O_(2)and Mn O in slag to reduce.In addition,the type of inclusions also evolved as the initial Al content increased.The evolution route of inclusions was Mn O→Mn O-Al_(2)O_(3)-Mg O→Mg O→Mn O-Ca O-Al_(2)O_(3)-Mg O and Mn O-Ca O-Mg O.The shape of inclusions evolved from spherical to irregular,became faceted,and finally transformed to spherical.The average size of inclusions presented a trend that was increasing first and then decreasing.The transformation mechanism of inclusions was explored.As the initial content of Al increased,Mg and Ca were reduced from top slag into molten steel in sequence,which consequently caused the transformation of inclusions.

Influence of Al Content on the Atmospheric Corrosion Behaviour of Magnesium-Aluminum Alloys

The influence of AI content on the Mg-AI alloys corrosion performance during sodium chloride induced atmospheric corrosion has been studied. It was found that the corrosion rate of three Mg-AI alloys was accelerated with increasing AI content. The poor corrosion resistance was attributed to the galvanic coupling between the phase and eutectic phase or α phase and the formation of porous corrosion products.

Effect of Al Content on the Isomerization Performance of Solid Superacid Pd–S_2O_8^(2-)/ZrO_2–Al_2O_3

The effect of Al content on the performance of the Pd–S2O82-/Zr O2–Al2O3solid superacid catalyst was studied using n-pentane isomerization as a probe reaction. The catalysts were also characterized by X-ray diffraction(XRD), Fourier transform Infrared(FTIR), specific surface area measurements(BET), thermogravimetry–differential thermal analysis(TG–DTA), H2-temperature programmed reduction(TPR) and NH3temperature-programmed desorption(NH3-TPD). The Pd–S2O82-/Zr O2–Al2O3catalyst made from Al2O3 mass fraction of 2.5% exhibited the best performance and its catalytic activity increased by 44.0% compared with Pd–S2O82-/Zr O2. The isopentane yield reached64.3% at a temperature of 238 °C, a reaction pressure of 2.0 MPa, a space velocity of 1.0 h-1and a H2/n-pentane molar ratio of 4.0. No obvious catalyst deactivation was observed within 100 h.

Effect of Al content on modification behavior of non-metallic inclusions in high-strength steel treated with rare earth

The influence of Al content(0.0053,0.0171,and 0.0578 wt.%)on the modification behavior of non-metallic inclusions in 20CrMoVTiB steel treated with rare earth elements was studied through high-temperature experiments and thermodynamic simulation.The results showed that the modification products varied with the Al content in steel under 0.01 wt.%of Ce addition.The formation sequence of typical rare earth inclusions in steel with the increase in Al content was Ce_(2)O_(3)→CeAlO_(3)→CeAl_(11)O_(18),and the final stable products were highly Al content dependent.When the Al content was 0.0053 wt.%,the stable phase in steel was Ce2O3;while the[Al]reached 0.0171 wt.%,the stable phase became CeA1O_(3).As the A1 content reached 0.0578 wt.%,CeAl_(11)O_(18) became the stable phase.As a result,increasing the Al content could inhibit the precipitation of Ce_(2)O_(3) inclusions in steel while promote the formation of CeAIO3 and CeAl_(11)O_(18) inclusions.In addition,both Ca treatment and Ce treatment could effectively refine the size of inclusions in steel by changing their types.However,the feeding amount of Ca wire into molten steel should be appropriately reduced under the condition of adding Ce simultaneously,which is expected to be beneficial for an improved Ce treatment effect.

Influence of Al Content on the Microstructure and Properties of the CrAlN Coatings Deposited by Arc Ion Plating

Four CrAlN coatings with various Al content were prepared by arc ion plating technology under different target currents. The effect of the Al content on the microstructure, chemical compositions, element chemical bonding states and mechanical properties of the CrAlN coatings was analyzed. X-ray diffraction results show that the primary phase of the CrAlN coating is fcc-（Al, Cr）N when the Al content is about 44.02 at.%. However, when the Al content increases to about 53.34 at.%, hcp-AlN phase emerges in the coating. And the hcp-AlN phase becomes the main phase in the CrAlN coating with Al content of about 69.55 at.%. Cross-sectional images show that all the four coatings possess dense structures and the deposition rate of Al atom is higher than that of Cr atom. The hardness of the CrAlN coating with Al content about 44.02 at.% is the largest （3149.72 HV） due to the solid solution hardening effect of the Al element. When the hcp-AlN phase is generated in the CrAlN coating, the hardness declines. The tribological experiment shows that the wear resistance of the CrAlN coating decreases gradually with increasing Al content when sliding against 100Cr6 steel ball.

Efect of Al Content on the Corrosion Behavior of Extruded Dilute Mg–Al–Ca–Mn Alloy

The microstructure,extrusion texture and corrosion behavior of extruded dilute Mg–Al–Ca–Mn alloy with diferent Al contents were investigated.The corrosion rate of the alloy was more sensitive to the Fe impurities.The 1.2 wt%Al showed the lowest corrosion rate,which was mainly attributed to the weakening of the cathode efect caused by the increase of the Al and the decrease of the Fe in the precipitated phase.Refned grains,stronger basal surface texture and higher corrosion potential deriving from the higher Al content of the matrix also further enhanced the corrosion resistance of the matrix.

Nitride-inclusion characterization in lightweight steel and re-precipitation behavior of AlN during heat treatment:effect of Al content

The composition,morphology,size,and number of inclusions in Fe-22Mn-xAl-0.7C(x=0.5%,5.2%,and 10.5%)lightweight steels after smelting and heat treatment experiments are characterized by scanning electron microscopy and energy-dispersive X-ray spectroscopy from both 2D and 3D perspectives.The inclusions are classified into eight categories according to chemistry and morphology.For the steel sample with a low Al content(0.5%),the inclusions are MnS,AlN-MnS,and Al_(2)O_(3)-MnS,among which Al_(2)O_(3)-MnS is the primary type.With the increase in Al content in the steel sample(to 5.2%),the populations of AlN and AlN-MnS inclusions of 1-3μm in diameter increase.A further increase in Al content(to 10.5%)leads to a significant decrease in the amount of AlN inclusions of 1-3μm in diameter,and an increase in the amount of AlN-MnS inclusions.The precipitation behavior during the phase transformation is also studied by FactSage 8.0 thermodynamic software,and a precipitation mechanism is proposed based on the calculation results.During the heat treatment,AlN inclusions re-precipitate out,due to the interactions between Al and dissolved N in the steel matrix.However,AlN inclusions cannot grow large because of unfavorable kinetic conditions.The re-precipitation phenomenon of AlN is predominant under low Al and high N conditions but not at high Al cases.

Al含量提高对IN 617合金持久性能及组织稳定性的影响

采用高温持久实验、扫描电镜(SEM)及透射电镜(TEM)等研究了Al含量提高对IN 617合金持久性能及组织稳定性的影响。结果表明:Al含量提高后,基于超过4万小时的实验数据,IN 617合金700℃、10万小时的外推持久强度超过170 MPa,持久性能显著提高,合金的持久断裂机制仍以微孔聚集长大为主;Al含量的提高会明显促进IN 617合金中γ′相的析出,提高其含量,同时也会促进合金中μ相和σ相等TCP相(Topologically close-packed phases)的析出,从而提高合金的硬度与持久性能,但尚未发现TCP相会对合金持久强度产生不利影响;时效处理时间越长,晶界析出相尺寸越大且愈加连续,致使晶界结合强度降低,而Al含量的提高又会提高晶内强度。二者共同作用,会使IN 617合金的持久塑性降低。

Sc对铸造Al-Li合金组织及力学性能的影响

铸造Al-Li合金可用于成型复杂薄壁构件,在航空航天、国防军工等领域具有广阔的应用前景。细化铸造Al-Li合金组织,提高合金强塑性对其实际应用具有重要意义。本文通过金属型铸造制备不同Sc含量的Al-2Li-2Cu-0.5Mg-xSc合金,分析了Sc含量对合金组织及力学性能的影响规律。结果表明,随着Sc含量逐渐增加,合金晶粒由树枝晶向近等轴晶转变,晶粒尺寸逐渐减小。δ'(Al_(3)Li)相倾向于以Al_(3)Sc相为形核核心,形成Al_(3)(Li, Sc)复合粒子,这些粒子在变形过程中不易被位错切过,减少了Al_(3)Li粒子引起的共面滑移。当添加0.3%Sc(质量分数)时,合金具有较好的综合力学性能,经过175℃/32 h的峰值时效处理后,屈服强度、抗拉强度和伸长率分别可以达到381.3 MPa、449.5 MPa和5.8%。

Cu含量以及Cu/Mg比对Al-Si-Cu-Mg合金组织和力学性能的影响

研究了Cu含量和Cu/Mg比对Al-Si-Cu-Mg合金组织和力学性能的影响。结果表明Al-Si-Cu-Mg合金凝固组织是否形成Mg_(2)Si、Q-Al_(5)Cu_(2)Mg_(8)Si_(6)以及θ-Al_(2)Cu取决于Cu含量以及Cu/Mg比。当Cu/Mg比相对低时形成Mg_(2)Si中间相,而Cu/Mg比高时则倾向于生成Q-Al_(5)Cu_(2)Mg_(8)Si_(6)和θ-Al_(2)Cu相。当Cu/Mg比相同时,高Cu含量和高Mg含量都会促进Q相θ相的形成。通过观察T6热处理后的组织发现Cu含量以及Cu/Mg比控制了初生相的溶解以及析出相的形成,从而影响合金的强度与韧性。通过控制Cu含量及Cu/Mg比使Al-9Si-2Cu-0.5Mg合金中析出较少数量的初生相,再通过热处理析出大量的Q′强化相,使合金具有较高的强度和相对适中的伸长率。

Al含量对含铝奥氏体不锈钢在高温超临界二氧化碳中均匀腐蚀性能的影响研究

为进一步提升奥氏体不锈钢作为超临界二氧化碳核反应堆候选包壳材料的耐腐蚀性能,对比研究了3种不同Al含量的含铝奥氏体不锈钢及不含Al基材在650℃/20 MPa的超临界二氧化碳环境中的均匀腐蚀行为。结果表明,材料的腐蚀增重随Al含量增加而降低,不同Al含量材料的腐蚀增重均近似服从抛物线生长规律。Al含量低于1.5wt%时,材料表面生成双层富Fe氧化膜,保护性差,渗碳层厚度可达约12μm;Al含量高于2.5wt%时,材料表面生成保护性氧化膜,外层富Cr、内层富Al,氧化膜及基体中仍存在渗碳行为,渗碳层厚度减小至约6μm。造成差异的原因是较高Al含量能有效促进保护性富Al氧化膜的形成,抑制Fe的向外扩散和C的向内扩散,进而提升材料的耐氧化和渗碳属性。

Effects of Al Content on Microstructure and Mechanical Property of CrAlN Coating Synthesized by Reactive Magnetron Sputtering

A series of CrAlN coatings with different Al content were synthesized on high-speed steel(M2)substrate by reactive direct current(DC)magnetron sputtering.The influences of Al content on the microstructure and mechanical property of CrAlN coatings were studied by scanning electron microscopy(SEM),X-ray diffraction(XRD),energy dispersive spectrum(EDS)and nano-indentation techniques,respectively.The results indicate that the coatings exhibit only fcc c-CrN phase when Al content is less than 65 at%,and fcc c-CrN and c-AlN phases when Al content is 78 at%.The coating with Al content of 60 at%exhibits high hardness and elastic modulus.The maximum hardness and elastic modulus values could reach 36.8 GPa and 459.5 GPa,respectively.

Mn微合金化Al-Si-Cu-Mg合金显微组织及耐蚀性能研究

Al-Si-Cu-Mg系列合金具有优异的强韧性,但其中的含Cu强化相极大地影响了该系合金的耐蚀性能。因此,本文通过对不同Mn含量的Al-7Si-2Cu-0.6Mg合金进行显微组织观察和电化学分析,探究Mn元素的添加对T6热处理状态下合金微观结构和耐蚀性的影响。结果表明,Mn添加量的提高对合金显微硬度几乎没有影响,但在合金基体中可以观察到弥散相。随着Mn含量升高,合金的耐蚀性呈现先升高后降低的趋势。添加0.360%Mn(质量分数)合金具有最佳耐蚀性,腐蚀电流密度比基础合金减少了54%。腐蚀形貌观察结果表明,Mn的添加可以显著减弱合金的点蚀趋势。

Ti含量对分别采用废料和全新料熔铸的Al-6.2Zn-2.1Mg-2.1Cu合金铸锭晶粒细化效果的影响

在用废料重熔和全新料熔炼的Al-6.2Zn-2.1Mg-2.1Cu合金中以AlTi5B1丝状中间合金的方式分别加入质量分数为0.005%、0.01%、0.02%、0.04%和0.06%的Ti,将铝液浇入铁模,获得小铸锭,研究Ti含量对铸锭晶粒细化效果的影响。结果表明,晶粒细化效果来源于新添加Ti,当添加w(Ti)=0.02%~0.04%时,Al-6.2Zn-2.1Mg-2.1Cu合金铸锭晶粒细化效果最佳。

Fe、Ni元素微合金化对Al-11Si铝合金微观组织及力学性能的影响

本研究利用扫描电子显微镜(SEM)、能量散射X射线光谱(EDS)和拉伸试验机,研究了Ni(1.2及1.6wt.%)和Fe(0.6及0.8wt.%)含量对Al-11Si铝合金的微观组织及不同温度下的力学性能的影响。实验结果表明,适量的Ni元素对于Al-11Si合金中富含Fe相的类型、形态和分布具有积极作用。在Al-11Si铝合金中添加1.2wt.%Ni和0.6wt.%Fe可以生成一种类似“汉字状”的富Fe强化相。当进一步增加到1.6wt.%Ni和0.8wt.%Fe后,富Fe相变为了长针状,对Al基体产生严重的割裂作用,降低了合金力学性能。由于含有1.2wt.%Ni和0.6wt.%Fe的Al-11Si铝合金中生成了“汉字状”富Fe强化相,合金的高温拉伸性能得到了显著改善。在350℃的测试温度下,Al-11Si铝合金的抗拉强度(UTS)达到了139 MPa。

高Al含量的亚稳β型Ti-Al-Mo-Nb-V系列钛合金的组织与力学性能

目前,亚稳β钛合金的成分朝着更高Al含量和更高β稳定元素含量的方向发展,本工作基于典型亚稳β钛合金β-21S和TB18的成分设计思路,添加了更高含量的Al元素,同时添加了Mo、Nb、V三种β稳定元素,设计并利用铜模吸铸法制备了高Al含量的亚稳β型Ti-Al-(Mo,Nb,V)系列钛合金。结果表明,Ti-6.5Al-1.5V-11.5Mo-2.8Nb合金在吸铸态下的β相结构达到临界稳定状态。此时,该合金的拉伸屈服强度为623 MPa,延伸率为16.6%,其屈服强度略低于对标合金TB18,但延伸率明显高于同系列合金和TB18合金,具有最佳的综合力学性能。此外,该合金液固温区为31℃,在同系列合金中最低,且明显低于对标合金TB18的液固温区238℃。

Effect of Cr content and cooling rate on the primary phase of Al-2.5Mn alloy

The effect of Cr content and cooling rate on the microstructure of Al-Mn alloy was studied using well resistance furnace melting,and the alloy was analyzed using scanning electron microscopy(SEM)and X-ray diffraction(XRD).The experimental results showed that adding Cr could significantly improve the morphology of the primary phase in the Al-2.5Mn alloy.Without Cr,the primary phase in the alloy was thick,needle-like,and strip-like structure.After adding 0.2wt%-0.5wt%Cr,the primary phase in the upper part of the alloy was gradually fined and reached the best effect at 0.35wt%Cr.When the content of Cr was 0.5wt%,the microstructure of the primary phase in the upper part began to coarsen.The bottom of the alloy was a large bulk phase,but still much finer than that without adding Cr.XRD and SEM analysis showed that the precipitation phase at the bottom was mainly Al85Mn7Cr8,while the fine microstructure at the top was Al6Mn and Al3Mn.The results of the cooling rate experiments showed that the primary phase of Al-2.5Mn-0.35Cr was further refined,and the eutectic microstructure was partly achieved,under air-cooling condition.And when the cooling method was iron die-cooling,the microstructure of the Al-2.5Mn-0.35Cr alloy was changed into a eutectic microstructure.

Cu含量对Al-Cu-Li合金淬火敏感性的影响

采用薄板叠层末端淬火的方法,通过强度测试、连续冷却转变(CCT)和时间-温度-转化率(TTT)曲线计算及X射线衍射、扫描电镜、透射电镜等微观组织表征方法,研究了Cu含量(3.15%、3.63%和3.88%)对Al-Cu-Li合金淬火敏感性的影响,结合理论分析,从析出驱动力和形核位点的角度分析了Cu含量影响淬火敏感性的机理。结果表明:随着Cu含量的增加,晶格畸变能增加,Li的溶解度降低,淬火态合金中位错和残留第二相增多,含Li相的析出驱动力和非均匀形核位点增加,淬火沉淀相增多;随着临界冷却速率的增大,鼻尖温度孕育期缩短,强度残存率减小,Al-Cu-Li合金淬火敏感性提高。T8态合金强度受Cu含量和淬火速率共同作用,淬火速率较高时,主要受Cu含量的影响;淬火速率较低时,Cu含量的影响减小。

Effect of carbon content on microstructure of in-situ Al_2O_(3p)-TiC_p/Al composites

The in situ Al 2O 3p TiC p/Al composite was fabricated by XD (exothermic dispersion) process in TiO 2 Al C system, and the effect of carbon content on the microstructure of the fabricated composite and the reactive temperature characteristics had been studied. The results show that carbon content affects the microstructure and reactive temperature of Al 2O 3p TiC p/Al composite greatly. The quantity of TiC phases in the fabricated composites increases, while the Al 3Ti phases reduces with increasing carbon content. And when C/TiO 2 molecular ratio is equal to one, the Al 3Ti phase nearly disappears. High temperature metallurgical field caused by strong exothermic reaction influences the synthetic reaction greatly, and higher synthetic temperature was favorable to the synthesis of Al 2O 3p TiC p reinforce particles.

Al含量对FeNiCoCrVAl高熵合金组织和力学性能的影响

通过XRD、SEM、EBSD和单轴拉伸测试,对不同Al含量(原子分数,%)Fe_(46-x)Ni_(20)Co_(20)Cr_(10)V_(4)Al_(x)(x=5,8,12,15)高熵合金的相结构、显微组织和力学性能进行了系统研究。结果表明,随着Al含量增加,Fe_(46-x)Ni_(20)Co_(20)Cr_(10)V_(4)Al_(x)高熵合金相结构由FCC单相转变为FCC+BCC双相结构,且强度随之增加,而塑性降低。其中,Fe_(34)Ni_(20)Co_(20)Cr_(10)V_(4)Al_(12)高熵合金在900℃退火处理后,具有极好的强塑性匹配,其屈服强度、抗拉强度和断裂延伸率分别为593 MPa、1009 MPa和32.13%。Al含量5%时,铸态和退火态高熵合金均为单一FCC相;Al含量8%,12%和15%时,高熵合金为FCC+BCC双相结构,退火处理促进了BCC相的析出,随着退火温度升高,BCC相占比增加。