OML:an online multi-particle locating method for high-resolution single-event effects studies

Identifying sensitive areas in integrated circuits susceptible to single-event effects(SEE)is crucial for improving radiation hardness.This study presents an online multi-track location(OML)framework to enhance the high-resolution online trajectory detection for the Hi’Beam-SEE system,which aims to localize SEE-sensitive positions on the IC at the micrometer scale and in real time.We employed a reparameterization method to accelerate the inference speed,merging the branches of the backbone of the location in the deployment scenario.Additionally,we designed an irregular convolution kernel,an attention mechanism,and a fused loss function to improve the positioning accuracy.OML demonstrates exceptional realtime processing capabilities,achieving a positioning accuracy of 1.83μm in processing data generated by the Hi’Beam-SEE system at 163 frames per second per GPU.

Investigation of maximum proton energy for qualified ground based evaluation of single-event effects in SRAM devices

Existing standards show a clear discrepancy in the specification of the maximum proton energy for qualified ground-based evaluation of single-event effects,which can range from 180 to 500 MeV. This work finds that the threshold linear energy transfer of a tested device is a critical parameter for determining the maximum proton energy. The inner mechanisms are further revealed. Highenergy deposition events(>10 MeV) in sensitive volumes are attributed to the interaction between protons and the tungsten vias in the metallization layers.

Single-event effects induced by medium-energy protons in 28 nm system-on-chip

Single-event effects(SEEs)induced by mediumenergy protons in a 28 nm system-on-chip(SoC)were investigated at the China Institute of Atomic Energy.An on-chip memory block was irradiated with 90 MeV and 70 MeV protons,respectively.Single-bit upset and multicell upset events were observed,and an uppermost number of nine upset cells were discovered in the 90 MeV proton irradiation test.The results indicate that the SEE sensitivities of the 28 nm SoC to the 90 MeV and 70 MeV protons were similar.Cosmic Ray Effects on Micro-Electronics Monte Carlo simulations were analyzed,and it demonstrates that protons can induce effects in a 28 nm SoC if their energies are greater than 1.4 MeV and that the lowest corresponding linear energy transfer was 0.142 MeV cm^2 mg^-1.The similarities and discrepancies of the SEEs induced by the 90 MeV and 70 MeV protons were analyzed.

Experimental study on heavy ion single-event effects in flash-based FPGAs

With extensive use of flash-based field-programmable gate arrays(FPGAs) in military and aerospace applications, single-event effects(SEEs) of FPGAs induced by radiations have been a major concern. In this paper, we present SEE experimental study of a flash-based FPGA from Microsemi Pro ASIC3 product family. The relation between the cross section and different linear energy transfer(LET) values for the logic tiles and embedded RAM blocks is obtained. The results show that the sequential logic cross section depends not too much on operating frequency of the device. And the relationship between 0 →1 upsets(zeros) and 1 →0 upsets(ones) is different for different kinds of D-flip-flops. The devices are not sensitive to SEL up to a LET of 99.0 Me V cm2/mg.Post-beam tests show that the programming module is damaged due to the high-LET ions.

An online fast multi-track locating algorithm for high-resolution single-event effect test platform

To improve the efficiency and accuracy of single-event effect(SEE)research at the Heavy Ion Research Facility at Lanzhou,Hi’Beam-SEE must precisely localize the position at which each heavy ion hitting the integrated circuit(IC)causes SEE.In this study,we propose a fast multi-track location(FML)method based on deep learning to locate the position of each particle track with high speed and accuracy.FML can process a vast amount of data supplied by Hi’Beam-SEE online,revealing sensitive areas in real time.FML is a slot-based object-centric encoder-decoder structure in which each slot can learn the location information of each track in the image.To make the method more accurate for real data,we designed an algorithm to generate a simulated dataset with a distribution similar to that of the real data,which was then used to train the model.Extensive comparison experiments demonstrated that the FML method,which has the best performance on simulated datasets,has high accuracy on real datasets as well.In particular,FML can reach 238 fps and a standard error of 1.6237μm.This study discusses the design and performance of FML.

Cumulative effects of excess high-normal alanine aminotransferase levels in relation to new-onset metabolic dysfunction-associated fatty liver disease in China

BACKGROUND Within the normal range,elevated alanine aminotransferase(ALT)levels are associated with an increased risk of metabolic dysfunction-associated fatty liver disease(MAFLD).AIM To investigate the associations between repeated high-normal ALT measurements and the risk of new-onset MAFLD prospectively.METHODS A cohort of 3553 participants followed for four consecutive health examinations over 4 years was selected.The incidence rate,cumulative times,and equally and unequally weighted cumulative effects of excess high-normal ALT levels(ehALT)were measured.Cox proportional hazards regression was used to analyse the association between the cumulative effects of ehALT and the risk of new-onset MAFLD.RESULTS A total of 83.13%of participants with MAFLD had normal ALT levels.The incidence rate of MAFLD showed a linear increasing trend in the cumulative ehALT group.Compared with those in the low-normal ALT group,the multivariate adjusted hazard ratios of the equally and unequally weighted cumulative effects of ehALT were 1.651[95%confidence interval(CI):1.199-2.273]and 1.535(95%CI:1.119-2.106)in the third quartile and 1.616(95%CI:1.162-2.246)and 1.580(95%CI:1.155-2.162)in the fourth quartile,respectively.CONCLUSION Most participants with MAFLD had normal ALT levels.Long-term high-normal ALT levels were associated with a cumulative increased risk of new-onset MAFLD.

Carbon Emission Effects Driven by Evolution of Chinese Dietary Structure from 1987 to 2020

Exploring carbon emission effects based on the evolution of residents’ dietary structure to achieve the carbon neutrality goal and mitigate climate change is an important task.This study took China as the research object(data excluding Hong Kong,Macao and Taiwan) and used the carbon emission coefficient method to quantitatively measure the food carbon emissions from 1987–2020,then analyzed the carbon emission effects under the evolution of dietary structure.The results showed that during the study period,the Chinese dietary structure gradually changed to a high-carbon consumption pattern.The dietary structure of urban residents developed to a balanced one,while that of rural residents developed to a high-quality one.During the study period,the per capita food carbon emissions and total food consumption of Chinese showed an increasing trend.The per capita food carbon emissions of residents in urban and rural showed an overall upward trend.The total food carbon emissions in urban increased significantly,while that in rural increased first and then decreased.The influence of beef and mutton on carbon emissions is the highest in dietary structure.Compared with the balanced dietary pattern,the food carbon emissions of Chinese residents had not yet reached the peak,but were evolving to a high-carbon consumption pattern.

Simulation of the Ecosystem Productivity Responses to Aerosol Diffuse Radiation Fertilization Effects over the Pan-Arctic during 2001–19

The pan-Arctic is confronted with air pollution transported from lower latitudes.Observations have shown that aerosols help increase plant photosynthesis through the diffuse radiation fertilization effects(DRFEs).While such DRFEs have been explored at low to middle latitudes,the aerosol impacts on pan-Arctic ecosystems and the contributions by anthropogenic and natural emission sources remain less quantified.Here,we perform regional simulations at 0.2o×0.2ousing a well-validated vegetation model(Yale Interactive terrestrial Biosphere,YIBs)in combination with multi-source of observations to quantify the impacts of aerosol DRFEs on the net primary productivity(NPP)in the pan-Arctic during 2001-19.Results show that aerosol DRFEs increase pan-Arctic NPP by 2.19 Pg C(12.8%)yr^(-1)under clear-sky conditions,in which natural and anthropogenic sources contribute to 8.9% and 3.9%,respectively.Under all-sky conditions,such DRFEs are largely dampened by cloud to only 0.26 Pg C(1.24%)yr^(-1),with contributions of 0.65% by natural and 0.59% by anthropogenic species.Natural aerosols cause a positive NPP trend of 0.022% yr^(-1)following the increased fire activities in the pan-Arctic.In contrast,anthropogenic aerosols induce a negative trend of-0.01% yr^(-1)due to reduced emissions from the middle latitudes.Such trends in aerosol DRFEs show a turning point in the year of 2007 with more positive NPP trends by natural aerosols but negative NPP trends by anthropogenic aerosols thereafter.Though affected by modeling uncertainties,this study suggests a likely increasing impact of aerosols on terrestrial ecosystems in the pan-Arctic under global warming.

Effects of urbanization and forest type on species composition and diversity,forest characteristics,biomass carbon sink,and their associations in Changchun,Northeast China:implications for urban carbon stock improvement

Differences in forest attributes and carbon sequestration of each organ and layer between broadleaved and conifer forests of central and outer urban areas are not well-defined,hindering the precise management of urban forests and improvement of function.To clarify the effect of two forest types with different urbanization intensities,we determined differences in vegetation composition and diversity,structural traits,and carbon stocks of 152 plots(20 m×20 m)in urban park forests in Changchun,which had the largest green quantity and carbon density effectiveness.We found that 1.1-fold thicker and healthier trees,and 1.6-to 2.0-fold higher,healthier,denser,and more various shrubs but with sparser trees and herbs occurred in the central urban forests(p<0.05)than in the outer forests.The conifer forests exhibited 30–70%obviously higher tree aboveground carbon sequestration(including stem and leaf)and 20%bigger trees,especially in the outer forests(p<0.05).In contrast,1.1-to 1.5-fold higher branch stocks,healthier and more diverse trees were found in broadleaved forests of both the inner and outer forests(p<0.05).Plant size and dominant species had similarly important roles in carbon stock improvement,especially big-sized woody plants and Pinus tabuliformis.In addition,a higher number of deciduous or needle species positively affected the broadleaved forest of the central urban area and conifer forest of the outer urban area,respectively.These findings can be used to guide precise management and accelerate the improvement of urban carbon function in Northeast China in the future.

Health Effects of Extreme Low Temperatures and Cold Waves on Respiratory Diseases

Climate change is the most significant threat to public health and exerts myriad influences on health,including the occurrence of extreme temperature events.Studies have demonstrated that populations will experience significantly severe cold waves in the future^([1]),increasing the risk of respiratory diseases.

Tilted Perpendicular Anisotropy-Induced Spin-Orbit Ratchet Effects

Using micromagnetic simulations, we demonstrate the tilted perpendicular anisotropy-induced spin-orbit ratchet effect. In spin-orbit torque(SOT)-induced magnetization switching, the critical currents required to switch between the two magnetization states(upward and downward magnetization) are asymmetric. In addition, in the nanowire structure, tilted anisotropy induces formation of tilted domain walls(DWs). The tilted DWs exhibit a ratchet behavior during motion. The ratchet effect during switching and DW motions can be tuned by changing the current direction with respect to the tilting direction of anisotropy. The ratchet motion of the DWs can be used to mimic the leaky-integrate-fire function of a biological neuron, especially the asymmetric property of the “potential” and “reset” processes. Our results provide a full understanding of the influence of tilted perpendicular anisotropy on SOT-induced magnetization switching and DW motion, and are beneficial for designs of further SOT-based devices.

Effects of Collocational Congruency,Frequency and L2 Proficiency on the Processing of English Adjective-Noun Collocations

The present study investigates the effects of congruency and frequency on adjective-noun collocational processing for Chinese learners of English at two proficiency levels based on the data obtained in an online acceptability judgment task.The subject pool of this research included 60 English majors studying at a university in China;30 were selected as a higher-proficiency group and 30 as a lower-proficiency group according to their Vocabulary Levels Test(Schmitt et al.,2001)scores and their self-reported proficiency in English.The experimental materials were programmed to E-prime 2.0 and included six types of collocations:(1)15 high-frequency congruent collocations,(2)15 low-frequency congruent collocations,(3)15 high-frequency incongruent collocations,(4)15 low-frequency incongruent collocations,(5)15 Chinese-only items,and(6)75 unrelated items for baseline data.The collected response times(RTs)and accuracy rates data were statistically analyzed by the use of an ANOVA test and pairwise comparisons through SPSS 16.0 software.The results revealed that:(1)the adjective-noun collocational processing of Chinese English learners is influenced by collocational frequency,congruency and L2 proficiency;(2)the processing time is affected by the interaction of congruency and frequency;and(3)the interactive effect of L2 proficiency in conjunction with congruency and frequency also influences the processing quality.

Cation effects in electrocatalytic reduction reactions:Recent advances

Electrocatalytic reduction reactions,powered by clean energy sources such as solar energy and wind,offer a sustainable method for converting inexpensive feedstocks(e.g.,CO_(2),N_(2)/NO_(x),organics,and O_(2))into high-value-added chemicals or fuels.The design and modification of electrocatalysts have been widely implemented to improve their performance in these reactions.However,bottle-necks are encountered,making it challenging to further improve performance through catalyst development alone.Recently,cations in the electrolyte have emerged as critical factors for tuning both the activity and product selectivity of reduction reactions.This review summarizes recent advances in understanding the role of cation effects in electrocatalytic reduction reactions.First,we introduce the mechanisms underlying cation effects.We then provide a comprehensive overview of their application in electroreduction reactions.Characterization techniques and theoretical calcula-tion methods for studying cation effects are also discussed.Finally,we address remaining challeng-es and future perspectives in this field.We hope that this review offers fundamental insights and design guidance for utilizing cation effects,thereby advancing their development.

Protective effects of baffles with different positions,row spacings,heights on debris flow impact

The baffle effectively slowed down debris flow velocity,reduced its kinetic energy,and significantly shortened the distance of debris flow movement.Consequently,they are widely used for protection against natural hazards such as landslides and mudslides.This study,based on the threedimensional DEM(Discrete Element Method),investigated the impact of different baffle positions on debris flow protection.Debris flow velocity and kinetic energy variations were studied through single-factor experiments.Suitable baffle positions were preliminarily selected by analyzing the influence of the first-row baffle position on the impact force and accumulation mass of debris flow.Subsequently,based on the selected baffle positions and four factors influencing the effectiveness of baffle protection(baffle position(P),baffle height(h),row spacing(S_(r)),and angle of transit area(α)),an orthogonal design was employed to further explore the optimal arrangement of baffles.The research results indicate that the use of a baffle structure could effectively slow down the motion velocity of debris flows and dissipate their energy.When the baffle is placed in the transit area,the impact force on the first-row baffle is greater than that when the baffle is placed in the deposition area.Similarly,when the baffle is placed in the transit area,the obstruction effect on debris flow mass is also greater than that when the baffle is placed in the deposition area.Through orthogonal experimental range analysis,when the impact on the first row of baffles is used as the evaluation criterion,the importance of each influencing factor is ranked asα>P>S_(r)>h.When the mass of debris flow behind the baffle is regarded as the evaluation criterion,the rank is changed to P>α>S_(r)>h.The experimental simulation results show that the optimal baffle arrangement is:P_(5),S_(r)=16,α=35°,h=9.

Kinetics insights into size effects of carbon nanotubes'growth and their supported platinum catalysts for 4,6-dinitroresorcinol hydrogenation

Size effects are a well-documented phenomenon in heterogeneous catalysis,typically attributed to alterations in geometric and electronic properties.In this study,we investigate the influence of catalyst size in the preparation of carbon nanotube(CNT)and the hydrogenation of 4,6-dinitroresorcinol(DNR)using Fe_(2)O_(3)and Pt catalysts,respectively.Various Fe_(2)O_(3)/Al_(2)O_(3)catalysts were synthesized for CNT growth through catalytic chemical vapor deposition.Our findings reveal a significant influence of Fe_(2)O_(3)nanoparticle size on the structure and yield of CNT.Specifically,CNT produced with Fe_(2)O_(3)/Al_(2)O_(3)containing 28%(mass)Fe loading exhibits abundant surface defects,an increased area for metal-particle immobilization,and a high carbon yield.This makes it a promising candidate for DNR hydrogenation.Utilizing this catalyst support,we further investigate the size effects of Pt nanoparticles on DNR hydrogenation.Larger Pt catalysts demonstrate a preference for 4,6-diaminoresorcinol generation at(100)sites,whereas smaller Pt catalysts are more susceptible to electronic properties.The kinetics insights obtained from this study have the potential to pave the way for the development of more efficient catalysts for both CNT synthesis and DNR hydrogenation.

Effects of Maternal Death on Children Living in the Sagnarigu Municipality

Introduction: The greatest effect of maternal mortality is renowned in children aged 2 - 5 months whose mothers had died. Children whose mothers died due to maternal complications were likely to record a higher mortality in infancy compared to children of surviving mothers. Motherless children mostly suffer a lot due to lack of day-to-day care, isolation, lack of motivation as well as economic cost associated with mother’s death. Thus, the purpose of this study was to ascertain the lives of children whose mothers passed away during childbirth at the Sagnarigu Municipality. Methods: This quantitative cross-sectional study was carried out at the Sagnarigu Municipal. The study recruited 297 respondents. To assess the effects of maternal death on the lives of children, families that experienced maternal death were assessed. The number of pregnancies experienced by the deceased woman, pregnancy-related complaints experienced, determinants of maternal death, number of children alive, and their standard of living were assessed with the aid of a structured questionnaire. Results: The data showed that negligence, illiteracy, poor road access, poverty, ignorance, delays in recognizing the problem, delays in making appropriate decisions, delays in the health facility, delays in giving the appropriate treatments, and traditional beliefs were some of the factors that led to maternal death in the Sagnarigu Municipality. Conclusion: The study concluded that determinants of maternal death in the Sagnarigu Municipal included the following;negligence, illiteracy, poverty, and delays in recognizing the problem. The study findings also demonstrated that the effects of maternal death on children are diverse and cut across different areas of a child’s life including livelihood sustenance, healthcare, education, and emotional and psychological development.

Theoretical study of kinetic isotope effects for vacancy diffusion of impurity in solids

Theoretical studies of the diffusionalisotope effect in solids are still stuck in the 1960s and 1970s.With the development of high spatial resolution mass spectrometers,isotopic data of mineral grains are rapidly accumulated.To dig up information from these data,molecularlevel theoretical models are urgently needed.Based on the microscopic definition of the diffusion coe fficient(D),a new theoretical framework for calculating the diffusional isotope effect(DIE(v))(intermsofD*/D)forvacancy-mediated impurity diffusion in solids is provided based on statistical mechanics formalism.The newly derived equation shows that theDIE(v)can be easily calculated as long as the vibration frequencies of isotope-substituted solids are obtained.The calculatedDIE(v)values of^(199)Au/^(195)Au and^(60)Co/^(57)Co during diffusion in Cu and Au metals are all within 1%of errors compared to the experimental data,which shows that this theoretical model is reasonable and precise.

Effects of Initial Defects on Effective Elastic Modulus of Concrete with Mesostructure

An exquisite mesostructure model was presented to predict the effective elastic modulus of concrete,in which concrete is realized as a four-phase composite material consisting of coarse aggregates,mortar matrix,interfacial transition zone(ITZ),and initial defects.With the three-dimensional(3D)finite element(FE)simulation,the highly heterogeneous composite elastic behavior of concrete was modeled,and the predicted results were compared with theoretical estimations for validation.Monte Carlo(MC)simulations were performed with the proposed mesostructure model to investigate the various factors of initial defects influencing the elastic modulus of concrete,such as the shape and concentration(pore volume fraction or crack density)of microspores and microcracks.It is found that the effective elastic modulus of concrete decreases with the increase of initial defects concentration,while the distribution and shape characteristics also exert certain influences due to the stress concentration caused by irregular inclusion shape.

Pharmacological effects of bioactive agents in earthworm extract:A comprehensive review

This review compiles information from the literature on the chemical composition,pharmacological effects,and molecular mechanisms of earthworm extract(EE)and suggests possibilities for clinical translation of EE.We also consider future trends and concerns in this domain.We summarize the bioactive components of EE,including G-90,lysenin,lumbrokinase,antimicrobial peptides,earthworm serine protease(ESP),and polyphenols,and detail the antitumor,antithrombotic,antiviral,antibacterial,anti-i nflammatory,analgesic,antioxidant,wound-healing,antifibrotic,and hypoglycemic activities and mechanisms of action of EE based on existing in vitro and in vivo studies.We further propose the potential of EE for clinical translation in anticancer and lipid-modifying therapies,and its promise as source of a novel agent for wound healing and resistance to antibiotic tolerance.The earthworm enzyme lumbrokinase embodies highly effective anticoagulant and thrombolytic properties and has the advantage of not causing bleeding phenomena due to hyperfibrinolysis.Its antifibrotic properties can reduce the excessive accumulation of extracellular matrix.The glycolipoprotein extract G-90 can effectively scavenge reactive oxygen groups and protect cellular tissues from oxidative damage.Earthworms have evolved a well-developed defense mechanism to fight against microbial infections,and the bioactive agents in EE have shown good antibacterial,fungal,and viral properties in in vitro and in vivo experiments and can alleviate inflammatory responses caused by infections,effectively reducing pain.Recent studies have also highlighted the role of EE in lowering blood glucose.EE shows high medicinal value and is expected to be a source of many bioactive compounds.

Review of Sc microalloying effects in Al-Cu alloys

Artificially controlling the solid-state precipitation in aluminum (Al) alloys is an efficient way to achieve well-performed properties,and the microalloying strategy is the most frequently adopted method for such a purpose.In this paper,recent advances in lengthscale-dependent scandium (Sc) microalloying effects in Al-Cu model alloys are reviewed.In coarse-grained Al-Cu alloys,the Sc-aided Cu/Sc/vacancies complexes that act as heterogeneous nuclei and Sc segregation at the θ′-Al_(2)Cu/matrix interface that reduces interfacial energy contribute significantly to θ′precipitation.By grain size refinement to the fine/ultrafine-grained scale,the strongly bonded Cu/Sc/vacancies complexes inhibit Cu and vacancy diffusing toward grain boundaries,promoting the desired intragranular θ′precipitation.At nanocrystalline scale,the applied high strain producing high-density vacancies results in the formation of a large quantity of (Cu Sc,vacancy)-rich atomic complexes with high thermal stability,outstandingly improving the strength/ductility synergy and preventing the intractable low-temperature precipitation.This review recommends the use of microalloying technology to modify the precipitation behaviors toward better combined mechanical properties and thermal stability in Al alloys.