Cycling performance of layered oxide cathode materials for sodium-ion batteries

Layered oxide is a promising cathode material for sodium-ion batteries because of its high-capacity,high operating voltage,and simple synthesis.Cycling performance is an important criterion for evaluating the application prospects of batteries.However,facing challenges,including phase transitions,ambient stability,side reactions,and irreversible anionic oxygen activity,the cycling performance of layered oxide cathode materials still cannot meet the application requirements.Therefore,this review proposes several strategies to address these challenges.First,bulk doping is introduced from three aspects:cationic single doping,anionic single doping,and multi-ion doping.Second,homogeneous surface coating and concentration gradient modification are reviewed.In addition,methods such as mixed structure design,particle engineering,high-entropy material construction,and integrated modification are proposed.Finally,a summary and outlook provide a new horizon for developing and modifying layered oxide cathode materials.

Dynamic Multi-Physics Behaviors and Performance Loss of Cylindrical Batteries Upon Low-Velocity Impact Loading

In challenging operational environments,Lithium-ion batteries(LIBs)inevitably experience mechanical stresses,including impacts and extrusion,which can lead to battery damage,failure,and even the occurrence of fire and explosion incidents.Consequently,it is imperative to investigate the safety performance of LIBs under mechanical loads.This study is grounded in a more realistic coupling scenario consisting of electrochemical cycling and low-velocity impact.We systematically and experimentally uncovered the mechanical,electrochemical,and thermal responses,damage behavior,and corresponding mechanisms under various conditions.Our study demonstrates that higher impact energy results in increased structural stiffness,maximum temperature,and maximum voltage drop.Furthermore,heightened impact energy significantly influences the electrical resistance parameters within the internal resistance.We also examined the effects of State of Charge(SOC)and C-rates.The methodology and experimental findings will offer insights for enhancing the safety design,conducting risk assessments,and enabling the cascading utilization of energy storage systems based on LIBs.

TiO_(2)-coated LiNi_(0.)9Co_(0.08)Al_(0.02)O_(2)cathode materials with enhanced cycle performance for Li-ion batteries

Ni-rich cathode material is one of the most promising materials for Li-ion batteries in electric vehicles.However,fading capacity,poor cyclic stability and high p H value are still major challenges,which suppress its practical application.In this study,spherical LiNi_(0.)9Co_(0.08)Al_(0.02)O_(2)powders with 0.4 wt%TiO_(2)coating layer were prepared by impregnation-hydrolysis method.Scanning electron microscopy(SEM),high-resolution transmission electron microscopy(HRTEM)and X-ray diffraction(XRD)results show that TiO_(2)is uniformly coated on the surface of LiNi_(0.)9Co_(0.08)Al_(0.02)O_(2)particle and slightly embedded into LiNi_(0.)9Co_(0.08)Al_(0.02)O_(2)particles.After 100 cycles at 2.0 C,0.4 wt%TiO_(2)-coated LiNi_(0.)9Co_(0.08)Al_(0.02)O_(2)electrode delivers much higher discharge capacity retention(77.0%)than the pristine LiNi_(0.)9Co_(0.08)Al_(0.02)O_(2)electrode(63.3%).The excellent cycling performance of 0.4 wt%Ti O_(2)-coated LiNi_(0.)9Co_(0.08)Al_(0.02)O_(2)electrode at a high discharge ratio is due to a TiO_(2)coating layer which can effectively reduce the direct contact between cathode material and electrolyte,suppress the oxidation of electrolyte,improve electrical conductivity of the electrode and increase the stability of the structure.

Toward high-sulfur-content,high-performance lithium-sulfur batteries:Review of materials and technologies

Lithium sulfur batteries(LSBs)are recognized as promising devices for developing next-generation energy storage systems.In addition,they are attractive rechargeable battery systems for replacing lithium-ion batteries(LIBs)for commercial use owing to their higher theoretical energy density and lower cost compared to those of LIBs.However,LSBs are still beset with some persistent issues that prevent them from being used industrially,such as the unavoidable dissolution of lithium polysulfide intermediates during electrochemical reactions and large volume expansion(up to 80%)upon the formation of Li_(2)S,resulting in serious battery life and safety limitations.In the process of solving these problems,it is necessary to maintain a high sulfur content in the cathode materials to ensure that the LSBs have high energy densities and excellent cycle performance.In this review,the novel preparation methods and cathode materials used for preparing LSBs in recent years are reviewed considering the sulfur content and cycle performance.In addition,the problems and difficulties in practically applying cathode materials are described,and the development trend is discussed.

KOH-assisted aqueous synthesis of ZIF-67 with high-yield and its derived cobalt selenide/carbon composites for high-performance Li-ion batteries

To solve the environmental pollution and low yield during the sythesis of zeolitic imidazolate frameworks(ZIFs)and their derived materials,a KOH-assisted aqueous strategy is proposed to synthesize cobalt zeolitic imidazolate framework(ZIF-67)polyhedrons,which are used as precursors to prepare cobalt selenide/carbon composites with different crystal phases(Co_(0.85)Se,CoSe_2).When evaluated as anode material for lithium ion batteries,Co_(0.85)Se/C composites deliver a reversible capacity of 758.7 m A·h·g^(-1)with a capacity retention rate of 90.5%at 1.0 A·g^(-1)after 500 cycles,and the superior rate capability is 620 m A·h·g^(-1)at 2.0 A·g^(-1).The addition of KOH accelerates the production of ZIF-67 crystals by boosting deprotonation of dimethylimidazole,resulting in rapid growth and structures transition from two-dimensional to three-dimensional of ZIF-67 in aqueous solution,which greatly promotes the application of MOFs in the field of energy storage and conversion.

Improved dehydrogenation cycle performance of the 1.1MgH_2-2LiNH_2-0.1LiBH_4 system by addition of La Ni_(4.5)Mn_(0.5) alloy

The isothermal desorption kinetics of the 1.1MgH2-2LiNH2-0.1LiBH4 system were improved by addition of LaNi4.5Mn0.5 alloy. The hydrogen desorption peak temperature of the sample containing LaNi4.5Mn0.5 reduced by approximately 5 K and the activation energy reduced by 9%. The results of isothermal dehydrogenation kinetics analysis implied that the isothermal desorption process at initial stage was controlled by the phase boundary mechanism. Moreover, the cycle performance of the materials was extended. The growth and agglomeration of the sample particles caused the deterioration of kinetics during de-/hydrogenation cycles, and then resulted in an incomplete desorption/absorption reaction which were responsible for the capacity fading. The cracking and pulverization of LaNi4.5Mn0.5 alloy had an obvious effect on preventing the composites aggregating, and the fine alloy particles could enhance the catalytic effect of the alloy, thus effectively offsetting part of the deterioration of kinetics caused by particles growth.

Al-modification for PS-PVD 7YSZ TBCs to improve particle erosion and thermal cycle performances

Plasma spray-physical vapor deposition(PS-PVD)as a novel process was used to prepare feather-like columnar thermal barrier coatings(TBCs).This special microstructure shows good strain tolerance and non-line-of-sight(NLOS)deposition,giving great potential application in aero-engine.However,due to serious service environment of aero-engine,particle erosion performance is a weakness for PS-PVD 7YSZ TBCs.As a solution,an Al-modification approach was proposed in this investigation.Through in-situ reaction of Al and ZrO2,anα-Al2O3 overlay can be formed on the surface of 7YSZ columnar coating.The results demonstrate that this approach can improve particle erosion resistance since hardness improvement of Al-modified TBCs.Meanwhile,as another important performance of thermal cycle,it has a better optimization with 350-cycle water-quenching,compared with the as-sprayed TBCs.

Synthesis and electrochemical performances of LiCoO_2 recycled from the incisors bound of Li-ion batteries

A new LiCoO2 recovery technology for Li-ion batteries was studied in this paper. LiCoO2 was peeled from the Al foil with dimethyl acetamide （DMAC）, and then polyvinylidene fluoride （PVDF） and carbon powders in the active material were eliminated by high temperature calcining. Subsequently, Li2CO3, LiOH-H20 and LiAc-2H2O were added into the recycled powders to adjust the Li/Co molar ratio to 1.00. The new LiCoO2 was obtained by calcining the mixture at 850℃ for 12 h in air. The structure and morphology of the recycled powders and resulting samples were studied by XRD and SEM techniques, respectively. The layered structure of LiCoO2 synthesized by adding Li2CO3 is the best, and it is found to have the best characteristics as a cathode material in terms of charge-discharge capacity and cycling performance. The first discharge capacity is 160 mAh·g^-1 between 3.0-4.3 V. The discharge capacity after cycling for 50 times is still 145.2 mAh·g^-1.

Lithium Hexamethyldisilazide Endows Li||NCM811 Battery with Superior Performance

The construction of stable cathode electrolyte interphase(CEI)is the key to improve the NCM811 particle structure and interfacial stability via electrolyte engineering.In He’s work,lithium hexamethyldisilazide(LiHMDS)as the electrolyte additive is proposed to facilitate the generation of stable CEI on NCM811 cathode surface and eliminate H_(2)O and HF in the electrolyte at the same time,which boosts the cycling performance of Li||NCM811 battery up to 1000 or 500 cycles with 4.5 V cut-off voltage at 25 or 60℃.

Effect of vinylene carbonate as electrolyte additive on cycling performance of LiFePO_4/graphite cell at elevated temperature

Effects of film-forming additive on stability of electrode and cycling performance of LiFePO4/graphite cell at elevated temperature were studied. Two 18650 cells with and without VC additive were investigated by galvanostatic cycling, electrochemical impedance spectroscopy, scanning electron microscopy, energy-dispersive X-ray analysis and Raman spectroscopy. The results show that in the presence of VC additive, dissolution of Fe from LiFePO4 material is greatly depressed and stability of graphite structure is improved; the additive can not only reduce reaction of electrolyte on surface of LiFePO4 electrode but also suppress reduction of solvent and thickening of the solid electrolyte interface （SEI） layer on graphite surface. Electrolyte with VC is considered to be a good candidate for improving cycling performance of the LiFePOa/graphite cell at elevated temperature.

Effect of sintering temperature on cycling performance and rate performance of LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2

LiNi0.8Co0.1Mn0.1O2 powder was prepared by mixing LiOH·H2O and co-precipitated Ni0.8Co0.1Mn0.1（OH）2 at a molar ratio of 1：1.05, followed by sintering at different temperatures. The effects of temperature on the morphology, structure and electrochemical performance were extensively studied. SEM and XRD results demonstrate that the sintering temperature has large influence on the morphology and structure and suitable temperature is very important to obtain spherical materials and suppresses the ionic distribution. The charge-discharge tests show that the electrochemical performance of LiNi0.8Co0.1Mn0.1O2 powders becomes better with the increase of temperature from 700 ℃ to 750 ℃ and higher temperature will deteriorate the performance. Although both of materials obtained at 750 ℃ and 780 ℃ demonstrate almost identical cyclic stability at 2C rate, which delivers 71.9%retention after 200 cycles, the rate performance of powder calcined at 780 ℃ is much poorer than that at 750 ℃. The XRD results demonstrate that the poor performance is ascribed to more severe ionic distribution caused by higher temperature.

Preparation and Investigation on Lattice Distortion and Electrochemical Performances of Li0.95Na0.05FePO4/C

Na^＋ doped sample Li0.95Na0.05FePO4 was prepared through solid state method. Structure characterization shows Na^＋ is successfully introduced into the LiFePO4 matrix. Scanning electron microscopy shows the particle size mainly ranges in 1-3 μm. X-ray diffraction Rietveld refinement demonstrates lattice distortion with an increased cell volume. As one cathode material, it has a discharge capacity of 150 mAh/g at 0.1 C rate. The material exhibits a capacity of 109 and 107 mAh/g at 5 and 7.5 C respectively. When cycled at 1 and 5 C, the material retains 84% （after 1000 cycles） and 86% （after 350 cycles） of the initial discharge capacity respectively indicating excellent structure stability and cycling performance. Na^＋ doping enhances the electrochemical activity especially the cycle performance effectively.

Effect of Y(OH)_3 microparticles on the electrochemical performance of alkaline zinc electrodes

This work focused on the zinc powder coated with Y(OH)3 microparticles by means of ultrasonic immersion for performance improvement of zinc electrodes in alkaline battery systems.Scanning electron microscopy and other characterization techniques were applied to examine the influence of the ultrasonic power on the sonochemical growth of Y(OH)3 microparticles in direct contact with zinc powder.Electrochemical properties of zinc electrodes containing Y(OH)3 microparticles were discussed through the measurement...

Core-shell mesoporous carbon hollow spheres as Se hosts for advanced Al-Se batteries

Incorporating a selenium(Se)positive electrode into aluminum(Al)-ion batteries is an effective strategy for improving the overall battery performance.However,the cycling stability of Se positive electrodes has challenges due to the dissolution of intermediate reaction products.In this work,we aim to harness the advantages of Se while reducing its limitations by preparing a core-shell mesoporous carbon hollow sphere with a titanium nitride(C@TiN)host to load 63.9wt%Se as the positive electrode material for Al-Se batteries.Using the physical and chemical confinement offered by the hollow mesoporous carbon and TiN,the obtained core-shell mesoporous carbon hollow spheres coated with Se(Se@C@TiN)display superior utilization of the active material and remarkable cycling stability.As a result,Al-Se batteries equipped with the as-prepared Se@C@TiN composite positive electrodes show an initial discharge specific capacity of 377 mAh·g^(-1)at a current density of 1000 mA·g^(-1)while maintaining a discharge specific capacity of 86.0 mAh·g^(-1)over 200 cycles.This improved cycling performance is ascribed to the high electrical conductivity of the core-shell mesoporous carbon hollow spheres and the unique three-dimensional hierarchical architecture of Se@C@TiN.

Improved High-rate Performance and Cycling Stability of 1D LiFePO_4 Nanorods by a Facile Annealing Process

To alleviate the main limitations of lithium ion diffusion rate and poor electronic conductivity for LiFePO4 cathode material, it is desirable to synthesize nano-size LiFePO4 material due to its enhanced electronic and lithium ion transport rates and thus an improved high-rate performance. However, our previous synthesized LiFePO4 nanorods only exhibited low high-rate and slightly unstable cycle performance. Possible reasons are the poor crystallization and Fe2＋ oxidation of LiFePO4 nanorods prepared by hydrothermal method. In this paper, LiFePO4 nanorods were simply dealt with at 700 ℃ for 4 h under the protection of Ar and H2 mixture gas. The electrochemical properties of LiFePO4/Li cells were investigated by galvanostatic test and cyclic voltammetry（CV）. The experimental results indicated that the annealed LiFePO4 nanorods delivered an excellent cycling stability and obviously improved capacity of 150 mA·h·g-1 at 1C, and even 122 mA·h·g-1 at 5C.

Supercapacitor electrode based on few-layer h-BNNSs/rGO composite for wide-temperature-range operation with robust stable cycling performance

Currently,developing supercapacitors with robust cycle stability and suitability for wide-temperature-range operations is still a huge challenge.In the present work,few-layer hexagonal boron nitride nanosheets(h-BNNSs)with a thickness of 2−4 atomic layers were fabricated via vacuum freeze-drying and nitridation.Then,the h-BNNSs/reduced graphene oxide(rGO)composite were further prepared using a hydrothermal method.Due to the combination of two two-dimensional(2D)van der Waals-bonded materials,the as-prepared h-BNNSs/rGO electrode exhibited robustness to wide-temperature-range operations from−10 to 50℃.When the electrodes worked in a neutral aqueous electrolyte(1 M Na2SO4),they showed a great stable cycling performance with almost 107%reservation of the initial capacitance at 0℃ and 111% at 50℃ for 5000 charge−discharge cycles.

High-performance self-organized Si nanocomposite anode for lithium-ion batteries

Silicon is being investigated extensively as an anodic material for next-generation lithium ion batteries for portable energy storage and electric vehicles.However,the large changes in volume during cycling lead to the breakdown of the conductive network in Si anodes and the formation of an unstable solid-electrolyte interface,resulting in capacity fading.Here,we demonstrate nanoparticles with a Si@Mn22.6Si5.4C4@C double-shell structure and the formation of self-organized Si-Mn-C nanocomposite anodes during the lithiation/delithiation process.The anode consists of amorphous Si particles less than 10 nm in diameter and separated by an interconnected conductive/buffer network,which exhibits excellent charge transfer kinetics and charge/discharge performances.A stable specific capacity of 1100 mAh·g-1 at 100 mA·g-1 and a coulombic efficiency of 99.2%after 30 cycles are achieved.Additionally,a rate capacity of 343 mAh·g-1 and a coulombic efficiency of 99.4%at 12000 mA·g-1 are also attainable.Owing to its simplicity and applicability,this strategy for improving electrode performance paves a way for the development of high-performance Si-based anodic materials for lithium ion batteries.

Dynamic test on waste heat recovery system with organic Rankine cycle

Dynamic performance is important to the controlling and monitoring of the organic Rankine cycle(ORC) system so to avoid the occurrence of unwanted conditions. A small scale waste heat recovery system with organic Rankine cycle was constructed and the dynamic behavior was presented. In the dynamic test, the pump was stopped and then started. In addition, there was a step change of the flue gas volume flow rate and the converter frequency of multistage pump, respectively. The results indicate that the working fluid flow rate has the shortest response time, followed by the expander inlet pressure and the expander inlet temperature.The operation frequency of pump is a key parameter for the ORC system. Due to a step change of pump frequency(39.49-35.24 Hz),the expander efficiency and thermal efficiency drop by 16% and 21% within 2 min, respectively. Besides, the saturated mixture can lead to an increase of the expander rotation speed.

Optimal Electrochemical Performances of CO_2 Activated Carbon Aerogels for Supercapacitors

Activated carbon aerogels（ACAs） derived from sol-gel polycondensation of resorcinol （R） and formaldehyde （F） were pyrolyzed under Ar flow and activated in CO2 atmosphere. The morphology of ACAs was characterized by scanning electron microscopy （SEM） and the structural properties were determined by N2 adsorption at 77 K. The results show that ACAs have a typical three-dimensional nanonetwork structure composing of cross-linking of carbon nanoparticles. The specific surface area and the total pore volume remarkably increase with increasing activation time while the previous porous structure still remains. The specific capacitance of the 950-10-ACA electrode can reach up to 212.3 F/g in 6 mol/L KOH electrolyte. The results of constant-current charge-discharge testing indicate that the ACAs electrodes present fast charge- discharge rate and long cycle life （about 98% capacitance retained after 3000 charge-discharge cycles at 1.25 mA/cm2）. Lower internal resistances can be achieved for 950-10-ACA electrode in KOH electrolyte. Our investigations are very important to improve the wettability and electrochemical performance of electrode for supercapacitors.

Structure Evolution and Electrochemical Performance of Al_2O_3-coated LiNi_(0.4)Co_(0.2)Mn_(0.4)O_2 During Charge-discharge Cycling

Several lithium-ion batteries of 18650-type were assembled with pristine or Al2O3-coated LiNi0.4Co0.2Mn0.4O2（NCM） as cathode material and mesocarbon microbeads（MCMB） as anode material.The cycling performance of the batteries was examined under 25 °C at a 2C rate within a potential range of 2.75―4.20 V.The changes of the crystal structure,the lattice parameter,the mean crystallite size,and the mean micro-strain of pristine NCM and Al2O3-coated NCM during the charge-discharge cycling were determined by X-ray diffraction（XRD）.The results indicate that the bulk structure of Al2O3-coated NCM is more stable than that of pristine NCM,which leads to the better cycling performance of Al2O3-coated NCM compared to that of pristine NCM.