New experimental method for inundation effect of film condensation on horizontal tube bundle

Theory of film condensation heat transfer(FCHT) for vapor condensed on horizontal tube bundle(HTB) is vital to many industry processes.Meanwhile,the inundation effect is the key to model the film condensation heat transfer coefficient(CHTC) on HTB.This paper proposed a new experimental method,homologous method,to obtain the inundation effect precisely.Based on the requirements of the new test method,a new test facility was designed and established.Then,the superiority of homologous method for inundation effect was investigated based on experiment result and theoretic analysis.The results showed that the homogenous method can effectively control the experimental error of inundation effect,which is less than 50% of the error of CHTC,and less than 30% of the error of the inundation effect gained by routine method.The new test facility built for the homogenous method is excellent in obtaining the accurate inundation effect of film condensation on HTB.All the result is a foundation of the theoretical development of the FCHT on HTB.

Preparation and Thermal Characterization of Diamond-Like Carbon Films

Diamond-like carbon （DLC） films are prepared on silicon substrates by microwave electron cyclotron resonance plasma enhanced chemical vapor deposition. Raman spectroscopy indicates that the films have an amorphous structure and typical characteristics. The topographies of the films are presented by AFM images. Effective thermal conductivities of the films are measured using a nanosecond pulsed photothermal reflectance method. The results show that thermal conductivity is dominated by the microstructure of the films.

Effects of Annealing Temperature on Structural and Optical Properties of ZnO Thin Films

The effects of annealing temperature on the structural and optical properties of ZnO films grown on Si （100） substrates by sol-gel spin-coating are investigated. The structural and optical properties are characterized by x-ray diffraction, scanning electron microscopy and photoluminescence spectra. X-ray diffraction analysis shows the crystal quality of ZnO films becomes better after annealing at high temperature. The grain size increases with the temperature increasing. It is found that the tensile stress in the plane of ZnO films first increases and then decreases with the annealing temperature increasing, reaching the maximum value of 1.8 GPa at 700℃. PL spectra of ZnO films annealed at various temperatures consists of a near band edge emission around 380 nm and visible emissions due to the electronic defects, which are related to deep level emissions, such as oxide antisite （OZn）, interstitial oxygen （Oi）, interstitial zinc （Zni） and zinc vacancy （VZn^-）, which are generated during annealing process. The evolution of defects is analyzed by PL spectra based on the energy of the electronic transitions.

Fabrication and Properties of Double-Side Tl2Ba2CaCu2O8 Thin Film on CeO2 Buffered Sapphire Substrate

The double-side Tl2Ba2 CaCu2O8 （Tl-2212） superconducting thin films were fabricated on CeO2 buffered sapphire substrates. The reactive magnetron sputtering technique was used to grow CeO2 buffer thin films on sapphire substrates. Making use of the metal cerium as a sputtering source, the depositing rate is much higher compared with the CeO2 target. The Ti-2212 thin films on CeO2 buffered sapphire substrates were fabricated by adc magnetron sputtering and post-annealing process. The x-ray diffraction indicates that the thin film is pure Tl-2212 phase with the e-axis perpendicular to the substrate surfaces, and epitaxially grown on the CeO2 buffered sapphire. The critical transition temperature Tc is around 106K, the critical current density Jc is around 3.5 MA/cm^2 at 77K, and the microwave surface resistance R8 at 77K and 10 CHz of the film is as low as 390μ Ω.

Influence of Post-Annealing Temperature on Properties of Ta-Doped ZnO Transparent Conductive Films

Ta-doped ZnO transparent conductive films are deposited on glass substrates by rf sputtering at 300℃. The influence of the post-annealing temperature on the structural, morphologic, electrical, and optical properties of the films is investigated by x-ray diffraction, Hall measurement, and optical transmission spectroscopy. The lowest resistivity of 3.5 ×10^-4 Ω·cm is obtained from the film annealed at 400℃in N2. The average optical transmittance of the films is over 90%. The optical bandgap is found to decrease with the increase of the annealing temperature.

Laser Damage Mechanisms of Amorphous Ta2O5 Films at 1064, 532 and 355nm in One-on-One Regime

Ta2O5 films are deposited on fused silica substrates by conventional e-beam evaporation. Surface topography and chemical composition are examined by atomic force microscopy （AFM） and x-ray photoelectron spectroscopy （XPS）. The calculation of electron structures of Ta2O5 and Ta2O5-x is attempted using a first-principle pseudopotential method within the local density approximation. The laser-induced damage threshold （LIDT） is performed at 1064, 532 and 355 nm in 1-on-1 regime, respectively. The results show that the LIDT increases with the wavelength increasing, which is in agreement with the wavelength effect. However, the LIDT results are not consistent with the empirical equation （I（λ）=aλm）, which may be attributed to the intrinsic absorption of Ta2O5 at the wavelengths of 532 or/and 355 nm. Moreover, different damage morphologies are observed when the films are irradiated at different wavelengths. It is concluded that the laser damage at 1064 nm is the defect dominant mechanism and at 355 nm it is the intrinsic absorption dominant mechanism, whereas at 532 nm it is the combined defect and intrinsic absorption dominant mechanism.

Fe-Vacancy-Induced Ferromagnetism in Tetragonal FeSe Thin Films

Motivated by recent experiments, we investigate structural, electronic, and magnetic properties of tetragonal FeSe with Fe vacancies using the state-of-the-art first-principles method. We show that Fe vacancies tend to stay in the same one of the two sublattices and thus induce ferromagnetism in the ground-state phase. Our calculated net moment is in good agreement with the experimental data available. Therefore, the ferromagnetism observed in tetragonal FeSe thin films is explained. It could be made controllable soon for spintronic applications.

Curvature Correction of FWHM in the X-Ray Rocking Curve of Bent Heteroepitaxial Films

A method for accurate determination of the curvature radius of semiconductor thin films is proposed. The curvature-induced broadening of the x-ray rocking curve （XRC） of a heteroepitaxially grown layer can be determined if the dependence of the full width at half maximum （FWHM） of XRC is measured as a function of the width of incident x-ray beam. It is found that the curvature radii of two GaN films grown on a sapphire wafer are different when they are grown under similar MOCVD conditions but have different values of layer thickness. At the same time, the dislocation-induced broadening of XRC and thus the dislocation density of the epitaxial film can be well calculated after the curvature correction.

Effects of Rapid Thermal Processing on Microstructure and Optical Properties of As-Deposited Ag2O Films by Direct-Current Reactive Magnetron Sputtering

（111） preferentially oriented Ag2O film deposited by direct current reactive magnetron sputtering is annealed by rapid thermal processing at different annealing temperatures for 5 min. The film microstructure and optical properties are then characterized by x-ray diffractometry, scanning electron microscopy, and spectrophotometry, respectively. The results indicate that no clear Ag diffraction peak is discernable in the Ag2O film annealed below 200°C. In comparison, the Ag2O film annealed at 200°C begins to exhibit characteristic Ag diffraction peaks, and in particular the Ag2O film annealed at 250°C can demonstrate enhanced Ag diffraction peaks. This implies that the threshold of the thermal decomposition reaction to produce Ag particles is approximately 200°C for the Ag2O film. In addition, an evolution of the film surface morphology from compact and pyramid-like to a rough and porous structure clearly occurred with increasing annealing temperature. The porous structure might be attributable to the escape of the oxygen produced during annealing, while the rough surface might originate from the reconstruction of the surface. The dispersion of interference peak intensity in the reflectance and transmission spectra could be attributed to the Ag particles produced. The lowered crystallinity and Ag particles produced induce a lattice defect, which results in an enhanced transmissivity in the violet region and a weakened transmissivity in the infrared region.

CuInSe2 Films Prepared by a Plasma-Assisted Selenization Process in Different Working Pressures

The effects of working pressure on the composition, structure and surface morphology properties of CuInSe2 （CIS） films selenized with a plasma-assisted selenization process is investigated. Higher selenium content, better crystalline quality and much more regular surface particles compared to the others are found in the CIS film with 40 Pa working pressure. A Cu（In,Ga）Se2 device fabricated with the optimized plasma-assisted selenization process is demonstrated to be better than our previous result. After discussion, the reason for these phenomena is attributed to the compromise of electron temperature and plasma density.

Competition between Radiative Power and Dissipation Power in the Refrigeration Process in Oxide Multifilms

The maximum refrigeration power dependence on the doping density in the p-BaTiO3/BaTiO3/SrTiO3/BaTiO3/ n-BaTiO3 system and in the p-AlGaAs/AlGaAs/GaAs/AlGaAs/n-AlGaAs system is obtained respectively based on the opto-thermionic refrigeration model. The results show that the maximum refrigeration power in the p-BaTiO3/BaTiO3/SrTiO3/BaTiO3/n-BaTiO3 system increases dramatically with the increase of doping density from 1.0×1018 cm-3 to 5.0×1019 cm-3 while that in the p-AlGaAs/AlGaAs/GaAs/AlGaAs/n-AlGaAs system is nearly a constant. It is found that the different Auger coefficients and the competition between radiative power and dissipation power lead to the different behavior of the maximum refrigeration power dependence on the doping density of the two systems.

Existence of Shear Horizontal Surface Waves in a Magneto-Electro-Elastic Material

The existence of shear horizontal surface waves in a magneto-electro-elastic （MEE） half-space with hexagonal （6mm） symmetry is investigated. The surface of the MEE half-space is mechanically free, but subjected to four types of electromagnetic boundary conditions. These boundary conditions are electrically open/magnetically closed, electrically open/magnetically open, electrically closed/magnetically open and electrically closed/magnetically dosed. It is shown that except for the electrically open/magnetically closed condition, the three other sets of electromagnetic boundary conditions allow the propagation of shear horizontal surface waves.

Synthesis and Properties of Magnetic Composites of Carbon Nanotubes/Fe Nanoparticle

Magnetic composites of carbon nanotubes （CNTs） are synthesized by the in situ catalytic decomposition of benzene at temperatures as low as 400℃ over Fe nanoparticles （mean grain size = 26 nm） produced by sol-gel fabrication and hydrogen reduction. The yield of CNT composite is up to about 3025% in a run of 6 h. FE- SEM and HRTEM investigations reveal that one-dimensional carbon species are produced in a large quantity. A relatively high value of magnetization is observed for the composite due to the encapsulation of ferromagnetic Fe3 C and/or α-Fe. The method is suitable for the mass-production of CNT composites that contain magnetic nanoparticles.

Preparation of High-Density Nanocrystalline Bulk Selenium by Rapid Compressing of Melt

The melt＇s solidification behavior of elemental selenium is investigated by a series of experiments including rapid compressing to 2.8 and 3.5 GPa within 20ms respectively, slow compressing to 2.8 GPa for 20 min and natural cooling at ambient pressure. Based on the x-ray diffraction, scanning electron microscope and transmission electron microscope results of the recovered samples, it is clearly shown that homogenous nanostructures are formed only by the rapid compression processes, and that the average crystal sizes are about 18.7 and 19.0 nm in the samples recovered from 2.8 and 3.5 GPa, respectively. The relative density of the nanocrystalline bulk reaches 98.17% of the theoretical value. It is suggested that rapid compression could induce pervasive nucleation and restrain grain growth during the solidification, which is related to fast supercooling, higher viscosity of the melt and lower diffusivity of atoms under high pressure.

Effects of Grain Boundary Barrier in ZnO/Si Heterostructure

The influence of ZnO microstructure on electrical barriers is investigated using capacitance-voltage （C - V）, current-voltage （I- V） and deep level transient spectroscopy （DLTS） measurements. A deep level center located at Ec - 0.24 eV obtained by DLTS in the ZnO films is an intrinsic defect related to Zni. The surface states in the ZnO grains that have acceptor behavior of capturing electrons from Zni defects result in the formation of grain barriers. In addition, we find that the current transport is dominated by grain barriers after annealing at 600℃ at 02 ambient. With the increment of the annealing temperature, the current transport mechanism of ZnO/Si heterostructure is mainly dominated by thermo-emission.

Nanoscale Thermal Response in ZnO Varistors by Atomic Force Microscopy

We report the application of customer-built scanning thermal microscopy （SThM） based on a commercial atomic force microscope to investigate local thermal inhomogeneity of ZnO varistors. The so-called 3ω method, generally used for measuring macroscale thermal conductivity, is set up and integrated with an atomic force microscope to probe the nanoseale thermal property. Remarkably, thermal contrasts of ZnO varistors are firstly imaged by the SThM, indicating the uniform distribution of spinel phases at triple points. The frequency-dependent thermal signal of ZnO varistors is also studied to present quantitative evaluation of local thermal conductivity of the sample.

Structural Feature and Solute Trapping of Rapidly Grown Ni3Sn Intermetallic Compound

The rapid dendritic growth of primary Ni3Sn phase in undercooled Ni-30.9%Sn-5%Ge alloy is investigated by using the glass fluxing technique. The dendritic growth velocity of Ni3Sn compound is measured as a function of undercooling, and a velocity of 2.47m/s is achieved at the maximum undercooling of 251 K （0.17TL）. The addition of the Ge element reduces its growth velocity as compared with the binary Ni75Sn25 alloy. During rapid solidification, the Ni3Sn compound behaves like a normal solid solution and it displays a morphological transition of ＂coarse dendrite-equiaxed grain-vermicular structure＂ with the increase of undereooling. Significant solute trapping of Ge atoms occurs in the whole undercooling range.

Effect of In Composition on Two-Dimensional Electron Gas in Wurtzite AlGaN/InGaN Heterostructures

The effect of In composition on two-dimensional electron gas in wurtzite AlGaN/InGaN heterostructures is theoretically investigated. The sheet carrier density is shown to increase nearly linearly with In mole fraction x, due to the increase in the polarization charge at the AlGaN/InGaN interface. The electron sheet density is enhanced with the doping in the AlGaN layer. The sheet carrier density is as high as 3.7×1013 cm^-2 at the donor density of 10×1018 cm^-3 for the HEMT structure with x=0.3. The contribution of additional donor density on the electron sheet density is nearly independent of the In mole fraction.

Production of ZnO Nanobelts and Meso-Scale Study of Mechanical Properties

We investigate a peculiar phenomenon by processing ZnO nanobelts with an atomic force microscope （AFM）. In the contact mode of AFM, peculiar bending occurs in meso-scale when the nanobelt is applied with force in lateral direction. We study the mechanical properties of ZnO nanobelts under the influence of small size effect, with finite element analysis and mathematical analysis by means of Matlab. Based on this abnormal effect, a novel measuring method is proposed, which allows the surface morphology and surface properties to be characterized at the same time.

Growth of Pure Zinc Blende GaAs Nanowires： Effect of Size and Density of Au Nanoparticles

Pure zinc blende GaAs nanowires were grown by metal organic chemical vapor deposition on GaAs（111）B substrates via Au catalyzed vapor-liquid-solid mechanism. The diameter, size distribution, and density of Au particles can be changed by varying the Au film thickness. We find that the grown nanowires are of rod-like shapes and pure zinc blende structure; moreover, the growth rate depends on the density of Au particles and it is independent of its diameters. It can be concluded that the nanowire was grown with main contributions from the direct impingement of vapor species onto the Au-Ga droplets and contributions from adatom diffusion can be negligible. The results indicate that the droplet acts as a catalyst rather than an adatom collector.