Hybrid Excitation Flux Switching Motor with Permanent Magnet Placed at Middle of Field Coil Slots and High Filling Factor Windings

Design and experimental studies on a hybrid excitation flux switching motor as a traction motor for hybrid electric vehicles drive are presented.A stator body of the motor consists of not only laminated silicon-iron electromagnetic steel and three-phase armature windings,but also both of field excitation coils and permanent magnets working together as a variable field magnetomotive force source.On the other hand,a rotor is composed of just laminated silicon-iron electromagnetic steel with salient poles like switched reluctance motor.To bring out the best in drive performances of the hybrid excitation flux switching motor as a variable flux motor for the application,each material adopted for the stator and rotor body should be designed properly in terms of motor efficiency,maximum torque and power densities and so forth.As some of them,in this paper,thinner silicon-iron electromagnetic steel sheet and permanent magnets with high remanent and low amount of Dysprosium used are applied for achieving higher motor efficiency.Moreover,all coils wound flatwise and edgewise using rectangular wires are introduced to realizing high filling factor for reduced copper losses.Experimental tests using a 60kW prototype of the motor demonstrates the designed motor has good motor efficiency under frequent operating points expected for the target vehicle drive.

Transmission Mechanism Based on Burst Filling in Hybrid Optical Burst/Circuit Switching Networks

Hybrid optical switching networks make full use of the advantages of Optical Circuit Switching(OCS)and Optical Burst Switching(OBS).In parallel hybrid optical switching networks,edge nodes choose a switching mode for traffic and no longer change.The inflexible decision making of the traffic transfer mode leads to low resource utilization when the arrival rate of the OCS traffic is lower than the capacity of the light path.In this paper,a new transmission scheme is proposed to improve resource utilization for hybrid optical switching networks.When the traffic arrival rate of the light path is lower than the transmission rate of the light path,the OCS traffic flow is reshaped at the edge nodes to generate a series of voids.Then,several message packets are sent along the light path to inform the core nodes of the voids of the light paths that represent the unused bandwidth resources.To improve the resource utilization,the voids can be filled with data bursts by core nodes.The simulation results show that the new scheme can effectively reduce the burst loss rate and improve the link utilization of the hybrid optical switching network on the premise of a providing service quality guarantee for OCS traffic.

Design and Implementation of Hybrid Light and Microwave Switches Based on Wavelength Selective Switch for Future Satellite Networks

A hybrid switching node structure with light and microwave links is proposed, which is applicable to the future data relay satellite systems, aiming at the development trend of coexistence of light- link and microwave-link in the future. An experimental system for the light and microwave hybrid switching node based on wavelength selective optical switches (WSS) and optical transceiver modules, is established. It is shown by our experiment that this hybrid switching node can realize the dynamic bandwidth allocation and wavelength routing while the bit error rate of light link is less than 10?12, which provides a method for solving the hybrid switching problem of light-link and microwave-link on the future data relay satellite systems.

Electric field control of deterministic current-induced magnetization switching in a hybrid ferromagnetic/ferroelectric structure

Subject Code:F04 With the support by the National Natural Science Foundation of China,a study by the research group led by Prof.Wang Kaiyou(王开友)from the Institute of Semiconductors,Chinese Academy of Sciences demonstrates all-electric and programmable manipulations of ferromagnetic bits without external

Fast response 2×2 thermo-optic switch with polymer/silica hybrid waveguide

A polymer/silica hybrid 2×2 multimode-interference switch is designed and fabricated. Instead of polymer Mach-Zehnder interferometer thermo-optic （TO） silica is used as under-cladding to accelerate heat release because of its large thermal conductivity. The developed switch exhibits low power consumption of 6.2 mW, low crosstalk of about 28 dB, and short response time. The rise and fall times of 103 and 91 its for this hybrid switch are shortened by 40.8% and 52.4%, respectively, compared with those of the fabricated TO switch （174 and 191 μs） using polymer as both upper- and under-claddings.

Fabrication of 2×2 Thermo-Optic Switches with Organic-Inorganic Hybrid Materials Prepared by Sol-Gel Technique

2×2 Mach-Zehnder interferometric thermo-optic switch was fabricated with organic/inorganic hybrid materials by sol-gel technique and direct UV patterning. The switching time of device was measured to be 4.2 ms and switching power 9.3 mW.

Performance evaluation of a WDM/OCDM based hybrid optical switch utilizing efficient resource allocation

A hybrid optical switch （HOS） with physical layer of wavelength division multiplexing and optical code division multiplexing （WDM/OCDM） scheme is proposed. An additional feature to the HOS than optical cross connect （OXC） is that the controller can process requests for both circuit establishment and burst scheduling. In our study, the measurement criteria of HOS are the blocking probability, probability of error, and probability of outage. To simplify the analysis, no distinction is made between a circuit in progress and a burst in progress. Moreover, a minimum fit （MinF） resource allocation strategy is applied in order to increase the bandwidth efficiency and control the multiplexing interference of the OCDM. A 2D Markov model for the HOS is presented using the MinF strategy. Numerical results reveal that the code parameters and the resource allocation strategy greatly affect the performance. Certain periority can be achieved by assigning shorter codes to high periority users and longer codes to low periority users. Also, the probability of error and outage are reduced bv aonling the MinF strategy.