Enhanced thermal and electrical properties of poly (D,L-lactide)/ multi-walled carbon nanotubes composites by in-situ polymerization

Biodegradable poly （D,L-lactide） （PLA）/carboxyl-functionalized multi-walled carbon nanotubes （c-MWCNTs） composites were achieved via in-situ polymerization. These as-prepared composite materials were characterized with FT-IR, XRD, TG, DSC, SEM, and high insulation resistance meter. The results demonstrate that the multi-walled carbon nanotube was carboxyl functionalized, which improved the collection between c-MWCNTs and PLA, and further realized the graft copolymerization of c-MWCNTs and PLA. There is a higher glass transition temperature and a lower pyrolysis temperature of PLA/c-MWCNTs composites than pure PLA. The c-MWCNTs gave a better dispersion than unmodified MWCNTs in the PLA matrix, and an even coating of PLA on the surface of c-MWCNTs was obtained, which increased the interfacial interaction. High insulation resistance analysis showed that the addition of c-MWCNTs increased the electric conductivity, and c-MWCNTs performed against the large dielectric coefficient and electrostatic state of PLA. These results demonstrated that c-MWCNTs modified PLA composites were beneficial for potential application in the development of heat-resisting and conductivity plastic engineering.

In-situ Polymerization-modification Process and Foaming of Poly（ethylene terephthalate）

Most of traditional linear poly(ethylene terephthalate)(PET)resins of relatively low molecular mass and narrow molecular mass distribution have low melt strength at foaming temperatures,which are not enough to support and keep cells.An in-situ polymerization-modification process with esterification and polycondensation stages was performed in a 2 L batch stirred reactor using pyromellitic dianhydride(PMDA)or pentaerythritol(PENTA)as modifying monomers to obtain PETs with high melt strength.The influence of amounts of modifying monomers on the properties of modified PET was investigated.It was found that the selected modifying monomers could effectively introduce branched structures into the modified PETs and improve their melt strength.With increasing the amount of the modifying monomer,the melt strength of the modified PET increased.But when the amount of PENTA reached 0.35%or PMDA reached 0.9%,crosslinking phenomenon was observed in the modified PET.Supercritical carbon dioxide(ScCO2)was employed as physical foaming agent to evaluate the foaming ability of modified PETs.The modified PETs had good foaming properties at 14 MPa of CO2pressure with foaming temperature ranging from 265°C to 280°C.SEM micrographs demonstrated that both modified PET foams had homogeneous cellular structures,with cell diameter ranging from 35μm to 49μm for PENTA modified PETs and38μm to 57μm for PMDA modified ones.Correspondingly,the cell density had a range of 3.5×107cells·cm 3to 7×106cells·cm 3for the former and 2.8×107cells·cm 3to 5.8×106cells·cm 3for the latter.

CHANGES OF STRUCTURE AND PROPERTIES OF POLY (ETHYLENE TEREPHTHALATE) CAUSED BY IN-SITU POLYMERIZATION OF PYRROLE

Conductive polymer composites based on crystalline polymer matrix have been prepared by using an in-situ polymerization process of pyrrole in amorphous poly （ethylene terephthalate） （PET） film. The DSC and WAXD measurement and SEM observation show that liquid-induced crystallization of PET matrix has occurred during the preparation of composite films. Depending upon the equilibrium degree of swelling and crystallinity, the limited depth of penetration of pyrrole molecules results in a skin-core structure of the composite film. The skin layer containing charge transfer intercalated polypyrrole has a surface resistance of 3.5×10;Ω. Rigid and heat-resistant polypyrrole molecules formed in PET film increase the tensile modulus and, especially, the rigidity of PET at elevated temperatures. However, they decrease the tensile strength and elongation at break, and impair the thermal ductility of PET.

SYNTHESIS AND CHARACTERIZATION OF POLYPROPYLENE/MONTMORILLONITE NANOCOMPOSITES VIA AN in-situ POLYMERIZATION APPROACH

Polypropylene/montmorillonite (PP/MMT)nanocomposites were prepared by in-situ polymerization using aMMT/MgCl_2/TiCl_4-EB Ziegler-Natta catalyst activated by triethylaluminum(TEA). The enlarged layer spacing of MMT wasconfirmed by X-ray wide angle diffraction (WAXD), demonstrating that MMT were intercalated by the catalyst components.X-ray photoelectron spectrometry (XPS) analysis proved that TiCl_4 was mainly supported on MgCl_2 instead of on the surfaceof MMT The exfoliated structure of MMT layers in the PP matrix of PP/MMT composites was demonstrated by WAXDpatterns and transmission electron microscopy (TEM) observation. The higher glass transition temperature and higher storage modulus of the PP/MMT composites in comparison with pure PP were revealed by dynamic mechanical analysis (DMA).

PREPARATION OF POLYSULFONAMIDE AND MODIFIED TITANIUM OXIDE NANOCOMPOSITES BY IN-SITU POLYMERIZATION

A kind of new nano composite with ultraviolet （UV） ray resistance and high temperature stability was prepared by in-situ polymerization in low temperature. Polysulfonamide （PSA） was synthesized with 4, 4＇-diaminodiphenyl sulfone （DDS） and terephthaloyl chloride （TPC） in the common solvent N, N-Dimethyl- -acetamide （DMAc）. Nano filler is a certain nano titanium oxide modified by silicon oxide （TMS）, which plays the role of UV resistance additives. Properties of the novel composite materials were characterized by Atomic Force microscopy （AFM）, thermal gravimetric Analysis （TGA） and Ultraviolet Spectroscopy. AFM had showed the sizes and distributions of TMS particles in the nanocomposite. Ultraviolet Spectroscopy for the nanocomposites showed a large absorption in UV band. TGA showed the decomposition temperature was increased over ten degrees with 0.5% wt TMS for this nanocomposite compared with pure PSA.

In-situ polymerization for PPy/g-C_3N_4 composites with enhanced visible light photocatalytic performance

Polypyrrole‐modified graphitic carbon nitride composites(PPy/g‐C3N4)are fabricated using an in‐situ polymerization method to improve the visible light photocatalytic activity of g‐C3N4.The PPy/g‐C3N4 is applied to the photocatalytic degradation of methylene blue(MB)under visible light irradiation.Various characterization techniques are employed to investigate the relationship between the structural properties and photoactivities of the as‐prepared composites.Results show that the specific surface area of the PPy/g‐C3N4 composites increases upon assembly of the amorphous PPy nanoparticles on the g‐C3N4 surface.Owing to the strong conductivity,the PPy can be used as a transition channel for electrons to move onto the g‐C3N4 surface,thus inhibiting the recombination of photogenerated carriers of g‐C3N4 and improving the photocatalytic performance.The elevated light adsorption of PPy/g‐C3N4 composites is attributed to the strong absorption coefficient of PPy.The composite containing 0.75 wt%PPy exhibits a photocatalytic efficiency that is 3 times higher than that of g‐C3N4 in 2 h.Moreover,the degradation kinetics follow a pseudo‐first‐order model.A detailed photocatalytic mechanism is proposed with·OH and·O2-radicals as the main reactive species.The present work provides new insights into the mechanistic understanding of PPy in PPy/g‐C3N4 composites for environmental applications.

Preparation of Polysulfonamide/ZnO Nanocomposite by In-Situ Polymerization

Polysulfonamide/zinc oxide(PSA/ZnO) nanocomposite films with w(ZnO)=0.5% were prepared by in-situ polymerization based on 4,4′-diaminodiphenylsulfone and terephthaloyl chloride in the common solvent N,N-Dimethylacetamide(DMAc). Atomic force microscopy (AFM) was employed to observe the microstructure of the composite film. The thermal property was investigated by TGA and mechanical property was characterized by DXLL-1000 electromechanical material testing machine. The results showed that the breaking strength of the film containing 0.5% ZnO was great enhanced. The average size of ZnO particles was below 100 nm. The introduction of ZnO as nano filler in PSA react as UV shield effect and make the composite mechanical property improved.

Thermoelectric properties of Bi_(0.5)Sb_(1.5)Te_3/polyaniline composites prepared by mechanical blending and in-situ polymerization

Bi 0.5 Sb 1.5 Te 3/polyaniline composites were prepared by mechanical blending and in situ polymerization, and their transport properties were measured. It was found that for the composites with 1%, 3%, 5% and 7% polyaniline (mass fraction) respectively, which were prepared by mechanical blending, the power factors decrease by about 30%, 50%, 55% and 65% compared with the Bi 0.5 Sb 1.5 Te 3 samples, which is mainly due to the remarkable decreases of the electrical conductivity. The electrical conductivity and power factor of the composites samples with 7% polyaniline prepared by in situ polymerization are higher by about 65% and 60%, respectively, than that of the corresponding samples prepared by mechanical blending.

FILLED POLYOLEFIN COMPOSITES PREPARED FROM IN-SITU POLYMERIZATION VIA A CATALYST-SUPPORTED APPROACH——Ⅰ.MORPHOLOGY OF PE IN CARBON BLACK(CB)/PE IN-SITU COMPOSITES

The morphology of PE in the in-situ CB/PE composites prepared from in-situ polymerization via a catalyst-supported approach was studied by DSC. It is found that both the melting peak temperature and crystallinity of the PE shelldecrease as filler level increases. The unexpected phenomena are ascribed to the strong interaction between PE and CB andthe very high specific area of CB. It is suggested that the lamellar thickness should be well correlated to the PE shell thickness. A two-layer PE model is successfully used to explain the experiment results.

Preparation of high vinyl polybutadiene/sepiolite nanocomposite by in-situ polymerization with new molybdenum-based catalyst

The dispersion of functional nanometer materials in polyolefin/clay nanocomposites is a key factor to determine the performances of mate-rials[1].In this research,the sepiolite with high specific surface area and good adsorption was introduced into the molybdenum-based butadiene polymerization system.Sepiolite-supporting MoCl5(Mo)function as the main catalysts,together with the alkyl aluminum(Al)substituted by m-cresol to form the butadiene coordination polymerization catalyst system to prepare high vinyl polybutadiene(HVPB)/sepiolite(Sep)nanocomposite.

Efficient in-situ end-functionalization of polydienes by isothiocyanate via neodymium mediated coordinative chain transfer polymerization system

End-functionalization of polydiene rubbers can not only improve its compatibility with inorganic fillers,but also enhance the overall mechanical properties.Nevertheless,for traditional neodymium(Nd)diene polymerization systems,it is highly challenging to achieve such end-functionalizations,because most of polydienyl chains are capped withη3-allyl-Nd moiety during the end of polymerization,which shows very poor reactivity with nucleophile compounds.We launched a new diene polymerization strategy calling coordinative chain transfer polymerization(CCTP)[1].In such a system,all the polydienyl chains are capped withη1-allyl-Al moieties,which reveal greater reactivity with cyclic esters and epoxide compounds,providing an effective manner to prepare polydiene-polyester amphiphilic block copolymers.Inspired by such findings,we now show herein how such types of chain-ends react with isot-hiocyanate to demonstrate an efficient in-situ manner to access end-functionalized polydienes by using CCTP.

3D printing encouraging desired in-situ polypyrrole seed-polymerization for ultra-high energy density supercapacitors

The tireless pursuit of supercapacitors with high energy density entails the parallel advancement of wellsuited electrode materials and elaborately engineered architectures.Polypyrrole(PPy)emerges as an exceedingly conductive polymer and a prospective pseudocapacitive materials for supercapacitors,yet the inferior cyclic stability and unpredictable polymerization patterns severely impede its real-world applicability.Here,for the first time,an innovative seed-induced in-situ polymerization assisted 3D printing strategy is proposed to fabricate PPy-reduced graphene oxide/poly(vinylidene difluoride-cohexafluoropropylene)(PVDF-HFP)(PPy-rGO/PH)electrodes with controllable polymerization behavior and exceptional areal mass loading.The preferred active sites uniformly pre-planted on the 3D-printed graphene substrates serve as reliable seeds to induce efficient polypyrrole deposition,achieving an impressive mass loading of 185.6 mg cm^(-2)(particularly 79.2 mg cm^(-2)for polypyrrole)and a superior areal capacitance of 25.2 F cm^(-2)at 2 mA cm^(-2)for a 12-layer electrode.In agreement with theses appealing features,an unprecedented areal energy density of 1.47 mW h cm^(-2)for a symmetrical device is registered,a rarely achieved value for other PPy/rGO-based supercapacitors.This work highlights a promising route to preparing high energy density energy storage modules for real-world applications.

In-situ polymerized PEO-based solid electrolytes contribute better Li metal batteries:Challenges,strategies,and perspectives

Polyethylene oxide(PEO)-based solid polymer electrolytes(SPEs)with good electrochemical stability and excellent Li salt solubility are considered as one of the most promising SPEs for solid-state lithium metal batteries(SSLMBs).However,PEO-based SPEs suffer from low ionic conductivity at room temperature and high interfacial resistance with the electrodes due to poor interfacial contact,seriously hindering their practical applications.As an emerging technology,in-situ polymerization process has been widely used in PEO-based SPEs because it can effectively increase Li-ion transport at the interface and improve the interfacial contact between the electrolyte and electrodes.Herein,we review recent advances in design and fabrication of in-situ polymerized PEO-based SPEs to realize enhanced performance in LMBs.The merits and current challenges of various SPEs,as well as their stabilizing strategies are presented.Furthermore,various in-situ polymerization methods(such as free radical polymerization,cationic polymerization,anionic polymerization)for the preparation of PEO-based SPEs are summarized.In addition,the application of in-situ polymerization technology in PEO-based SPEs for adjustment of the functional units and addition of different functional filler materials was systematically discussed to explore the design concepts,methods and working mechanisms.Finally,the challenges and future prospects of in-situ polymerized PEO-based SPEs for SSLMBs are also proposed.

SiO_(2) nanofiber composite gel polymer electrolyte by in-situ polymerization for stable Li metal batteries

Gel polymer electrolytes(GPEs) are promising alternatives to liquid electrolytes applied in high-energydensity batteries.Here superior SiO_(2) nanofiber composite gel polymer electrolytes(SNCGPEs) are developed via in-situ ionic ring-opening polymerization of 1,3-dioxolane(DOL) monomers in SiO_(2) nanofiber membrane(PDOL-SiO_(2)) for lithium metal batteries.The oxygen atoms of PDOL together with Si-O of SiO_(2) construct a more efficient channel for Li^(+) migration.Consequently,the lithium ion transference number(t_(Li^(+)) and ionic conductivity(σ) at 30℃ of PDOL-SiO_(2) are 0.80 and 1.68×10^(-4)S/cm separately.PDOL-SiO_(2) manifests the electrochemical decomposition potentials of 4.90 V.At 0.5 mA/cm^(2),Li|PDOL-SiO_(2) |Li cell shows a steady cycling performance for nearly 1400 h.LFP|PDOL-SiO_(2) |Li battery can steadily cycle at 0.5 C with a capacity retention rate of 89% after 200 cycles.While cycling at 2 C,the capacity retention rate can maintain at 78% after 300 cycles.This contribution provides a innovative strategy for accelerating Li^(+)transportation via designing PDOL molecular chains throughout the SiO_(2) nanofiber framework,which is crucial for high-energy-density LMBs.

Preparation of pH-Responsive Doxorubicin Nanocapsules by Combining High-gravity Antisolvent Precipitation with In-situ Polymerization for Intracellular Anticancer Drug Delivery

Owing to the low pH value in tumor and cancer cells,drug delivery systems based on pH-responsive polymer nanocarriers have been extensively explored for anticancer chemotherapy.Herein,we developed a pH-responsive doxonibicin(EXDX)nanocapsule(named as DNanoCapsule)prepared by combining in-situ polymerization teclinique with high-gravity antisolvent precipitation technique throngh an amphiphilic polymerized surface ligand.DNanoCapsules show an obvious spherical core-shell structure with a single DOX nanoparticle encapsulated in the polymer layer.Dissolution rate studies prove that the DNanoCapsules have robust dnig-release profiles under acidic environments due to the division of the pH-sensitive cross-linker,which triggers thecollapse of the polymer layer.The in vitro investigations demonstrated that the DNanoCapsules exhibited higli cellular uptake efficiency and cytotoxicity for both HeLa and MCF-7 cancer cells.Tlierefore,this work may provide a promising strategy to design and develop various stimuli-responsive drug nanocapsules tor the treatment of cancer or other diseases.

Screening the Insecticidal Efficacy of Nano ZnO Synthesized via in-situ Polymerization of Crosslinked Polyacrylic Acid as a Template

Nano zinc oxide （ZnO） is a very useful and important material in many industrial and biological applications. In the present work, ZnO was synthesized by post thermal degradation of the precursor ＂zinc acetate di-hydrate＂ templated in crosslinked polyacrylic acid （PAA）. The crosslinked PAA template was prepared through an in-situ polymerization process adopted in presence of ammonium per sulphate, as an initiator, and N, Nt- methylene bis-acrylamide as the crosslinker. Variation of preparation parameters and their impact on the oxide stoichiometry, crystal structure, crystallite size and surface texture of the oxide were investigated. Energy dispersive X-ray technique （EDX）, X-ray diffraction （XRD） and scanning electron microscopy （SEM） were convincingly used to reveal the oxide structural features and characteristics. The performed bioassay tests indicated the efficacy of this method of preparation to produce nano ZnO with novel insecticidal activity against the greater wax moth, Galleria rnellonella.

P(AN-MMA)/TiO_2 Nano-composite Polymer Electrolyte by in-situ Polymerization

1 Introduction With the development of portable electric devices,polymer lithium ion batteries (PLiBs) have been widely used as the power sources because of their high energy density and safe property[1].P(AN-MMA) copolymer is a kind of cheap macromolecules easily dissolving in the polar solvents such as carbonate,it has been applied as gel polymer electrolyte in PLiBs.Here we prepare a kind of highly conductive nano-composite polymer electrolytes using the P(AN-MMA) copolymer incorporated with TiO2 nan...

A combined interfacial and in-situ polymerization strategy to construct well-defined core-shell epoxy-containing SiO_(2) - based microcapsules with high encapsulation loading, super thermal stability and nonpolar solvent tolerance

SiO_(2)-based microcapsules containing hydrophobic molecules exhib-ited potential applications such as extrinsic self-healing,drug delivery,due to outstanding thermal and chemical stability of SiO_(2).However,to construct SiO_(2)-based microcapsules with both high encapsulation loading and long-term structural stability is still a troublesome issue,limiting their further utilization.We herein design asingle-batch route,a combined interfacial and in-situ polymerization strategy,to fabricate epoxy-containing SiO_(2)-based microcapsules with both high encapsu-lation loading and long-term structural stability.The final SiO_(2)-based microcapsules preserve high encapsulation loading of 85.7 wt% by controlling exclusively hydrolysis and condensed polymerization at oil/water interface in the initial interfacial polymerization step.In the subsequent in-situ polymerization step,the initial SiO_(2)-based microcapsules as seeds could efficiently harvest SiO_(2) precursors and primary SiO 2 particles to finely tune the SiO_(2) wall thickness,thereby enhancing long-term structural stability of the final SiO_(2)-based microcapsules including high thermal stability with almost no any weight loss until 250℃,and strong tolerance against nonpolar solvents such as CCl_(4) with almost unchanged core-shell structure and unchanged core weight after immersing into strong solvents for up to 5 days.These SiO_(2)-based microcapsules are extremely suited for processing them into anticorrosive coating in the presence of nonpolar solvents for self-healing application.

Lithium Salt Combining Fluoroethylene Carbonate Initiates Methyl Methacrylate Polymerization Enabling Dendrite-Free Solid-State Lithium Metal Battery

This work demonstrates a novel polymerization-derived polymer electrolyte consisting of methyl methacrylate,lithium bis(trifluoromethanesulfonyl)imide and fluoroethylene carbonate.The polymerization of MMA was initiated by the amino compounds following an anionic catalytic mechanism.LiTFSI plays both roles including the initiator and Li ion source in the polymer electrolyte.Normally,lithium bis(trifluoromethanesulfonyl)imide has difficulty in initiating the polymerization reaction of methyl methacrylate monomer,a very high concentration of lithium bis(trifluoromethanesulfonyl)imide is needed for initiating the polymerization.However,the fluoroethylene carbonate additive can work as a supporter to facilitate the degree of dissociation of lithium bis(trifluoromethanesulfonyl)imide and increase its initiator capacity due to the high dielectric constant.The as-prepared poly-methyl methacrylate-based polymer electrolyte has a high ionic conductivity(1.19×10^(−3)S cm^(−1)),a wide electrochemical stability window(5 V vs Li^(+)/Li),and a high Li ion transference number(t_(Li^(+)))of 0.74 at room temperature(RT).Moreover,this polymerization-derived polymer electrolyte can effectively work as an artificial protective layer on Li metal anode,which enabled the Li symmetric cell to achieve a long-term cycling performance at 0.2 mAh cm^(−2)for 2800 h.The LiFePO_(4)battery with polymerization-derived polymer electrolyte-modified Li metal anode shows a capacity retention of 91.17%after 800 cycles at 0.5 C.This work provides a facile and accessible approach to manufacturing poly-methyl methacrylate-based polymerization-derived polymer electrolyte and shows great potential as an interphase in Li metal batteries.

Preparation of poly （methyl methacrylate）／nanometer calcium carbonate composite by in-situ emulsion polymerization

Methyl methacrylate (MMA) emulsion polymerization in the presence of nanometer calcium carbonate(nano-CaCO3) surface modified with γ-methacryloxypropyltrimethoxysilane (MPTMS) was carried out to prepare poly (methyl methacrylate) (PMMA)/nano-CaCO3 composite. The reaction between nano-CaCO3 and MPTMS, and the grafting of PMMA onto nano-CaCO3 were confirmed by infrared spectrum. The grafting ratio and grafting efficiency of PMMA on nano-CaCO3 modified with MPTMS were much higher than that on nano-CaCO3 modified with stearic acid. The grafting ratio of PMMA increased as the weight ratio between MMA and nano-CaCO3 increased, while the grafting efficiency of PMMA decreased. Transmission electron micrograph showed that nano-CaCO3 covered with PMMA was formed by in-situ emulsion polymerization.