Relationship Between Iron Oxides and Surface Charge Characteristics in Soils

The relationship between iron oxides and surface charge characteristics in variable charge soils ( latosol and red earth ) was studied in following three ways. ( 1 ) Remove free iron oxides ( Fed ) and amorphous iron oxides ( Feo ) from the soils with sodium dithionite and acid ammonium oxalate solution respectively. ( 2 ) Add 2% glucose ( on the basis of air-dry soil weight ) to soils and incubate under submerged condition to activate iron oxides, and then the mixtures are dehydrated and air-dried to age iron oxides. ( 3 ) Precipitate various crystalline forms of iron oxides onto kaolinite. The results showed that free iron oxides ( Fed ) were the chief carrier of variable positive charges. Of which crystalline iron oxides ( Fed-Feo ) presented mainly as discrete particles in the soils and could only play a role of the carrier of positive charges, and did little influence on negative charges. Whereas the amorphous iron oxides ( Feo ) , which presented mainly as a coating with a large specific surface area, not only had positive charges, but also blocked the negative charge sites in soils. Submerged incubation activated iron oxides in the soils, and increased the amount of amorphous iron oxides and the degree of activation of iron oxide, which resulted in the increase of positive and negative charges of soils. Dehydration and air-dry aged iron oxides in soils and decreased the amount of amorphous iron oxides and the degree of activation of iron oxide, and also led to the decrease of positive and negative charges. Both the submerged incubation and the dehydration and air-dry had no significant influence on net charges. Precipitation of iron oxides onto kaolinite markedly increased positive charges and decreased negative charges. Amorphous iron oxide having a larger surface area contributed more positive charge sites and blocked more negative charge sites in kaolinite than crystalline goethite.

Magnetic labeling of primary murine monocytes using very small superparamagnetic iron oxide nanoparticles

Due to their very small size,nanoparticles can interact with all cells in the central nervous system.One of the most promising nanoparticle subgroups are very small superparamagnetic iron oxide nanoparticles(VSOP)that are citrate coated for electrostatic stabilization.To determine their influence on murine blood-derived monocytes,which easily enter the injured central nervous system,we applied VSOP and carboxydextran-coated superparamagnetic iron oxide nanoparticles(Resovist).We assessed their impact on the viability,cytokine,and chemokine secretion,as well as iron uptake of murine blood-derived monocytes.We found that(1)the monocytes accumulated VSOP and Resovist,(2)this uptake seemed to be nanoparticle-and time-dependent,(3)the decrease of monocytes viability was treatment-related,(4)VSOP and Resovist incubation did not alter cytokine homeostasis,and(5)overall a 6-hour treatment with 0.75 mM VSOP-R1 was probably sufficient to effectively label monocytes for future experiments.Since homeostasis is not altered,it is safe to label blood-derived monocles with VSOP.VSOP labeled monocytes can be used to study injured central nervous system sites further,for example with drug-carrying VSOP.

Preparation of Superparamagnetic Dextran-coated Iron Oxide Nanoparticles used as a Novel Gene Carrier into Human Bladder Cancer Cells'

Objective: Application of magnetic nanoparticles as gene carrier in gene therapy has developed quickly. This study was designed to investigate the preparation of superparamagnetic dextran-coated iron oxide nanoparticles (SDION) and the feasibility of SDION used as a novel gene carrier for plasmid DNA in vitro. Methods: SDION were prepared by chemical coprecipitation and separated by gel filtration on Sephacryl S-300HR, characterized by TEM, laser scattering system and Vibrating Sample Magnetometer Signal Processor. The green fluorescent protein (pGFP-C2) plasmid DNA was used as target gene. SDION-pGFP-C2 conjugate compounds were produced by means of oxidoreduction reaction. The connection ratio of SDION and pGFP-C2 DNA was analyzed and evaluated by agarose electrophoresis and the concentration of pGFP-C2 in supernatant was measured. Using liposome as control, the transfection efficiency of SDION and liposome was respectively evaluated under fluorescence microscope in vitro. Results: The diameter of SDION ranges from 3 nm to 8 nm, the effective diameter was 59.2 nm and the saturation magnetization was 0.23 emu/g. After SDION were reasonably oxidized, SDION could connect with pGFP-C2 to a high degree. The transfection efficiency of SDION as gene carrier was higher than that of liposome. Conclusion: The successes in connecting SDION with pGFP-C2 plasmid by means of oxidoreduction reaction and in transferring pGFP-C2 gene into human bladder cancer BIU-87 cells in vitro provided the experimental evidence for the feasibility of SDION used as a novel gene carrier.

Study on Kinetics of Iron Oxide Reduction by Hydrogen

Kinetics parameters of iron oxide reduction by hydrogen were evaluated by the isothermal method in a differential micro-packed bed. Influence of external diffusion, internal diffusion and heat transfer on the intrinsic reaction rate was investigated and the conditions free of internal and external diffusion resistance have been determined. In the experiments, in order to correctly evaluate the intrinsic kinetics parameters for reducing Fe203 to Fe3O4, the reaction temperatures were set between 440 ℃ and 490 ℃. However, in order to distinguish the reduction of Fe304 to FeO from that of FeO to Fe, the reaction temperature in the experiment was set to be greater than 570 ℃. Intrinsic kinetics of iron oxide reduction by hydrogen was established and the newly established kinetic models were validated by the experimental data.

Reduction kinetics of iron oxide pellets with H_2 and CO mixtures

Reduction of hematite pellets using H2-CO mixtures with a wide range of H2/CO by molar （1：0, 3：1, 1：1, 1：3, and 0：1） at different reducing temperatures （1073, 1173, and 1273 K） was conducted in a program reducing furnace. Based on an unreacted core model, the effective diffusion coefficient and reaction rate constant in several cases were determined, and then the rate-control step and transition were analyzed. In the results, the effective diffusion coefficient and reaction rate constant increase with the rise in temperature or hydrogen content. Reduction of iron oxide pellets using an H2-CO mixture is a compound control system; the reaction rate is dominated by chemical reaction at the very beginning, competition during the reduction process subsequently, and internal gas diffusion at the end. At low hydrogen content, increasing temperature takes the transition point of the rate-control step to a high reduction degree, but at high hydrogen content, the effect of temperature on the transition point weakens.

Ceramsite Containing Iron Oxide and its Use as Functional Aggregate in Microwave Absorbing Cement-based Materials

Electromagnetic（EM） wave absorbing cement-based composite has promising applications in protecting civil and military buildings from electromagnetic interferences. A new idea of preparing EM wave absorbing cement-based composite is proposed by using ceramsite containing iron oxide as EM wave absorbing functional aggregate. The ceramsite was synthesized by adding 10 wt% Fe3O4 into clay and sintering at 1 200 ℃, which shows obvious dielectric and magnetic loss properties for electromagnetic wave. The maximum reflection loss（RL） of the concrete specimens prepared with the ceramsite is between-10.2--10.7 dB（corresponding to absorption greater than 90% EM energy） in the bandwidth of 8-18 GHz. In addition, the compressive strength at 28 days age of the concrete is 46 MPa, showing the potentiality of being used as structural components in buildings.

Characterization of Iron Oxide Generated in Ruthner Plant of Pickling Unit in Mobarakeh Steel Complex

Reducing the chloride content in regenerated iron oxides (RIO) from steel-pickling acid waste economically treated by Ruthner process is the most critical issue for the development of RIO as a useful raw material resource. In this paper, the results of a new method for characterization and modification of RIO produced in Mobarakeh Steel Complex were reported.

Effect of Calcium Oxide Additive on the Performance of Iron Oxide Sorbent for High-Temperature Coal Gas Desulfurization

The effect of calcium oxide additive in iron oxide sorbent for hot gas desulfurization was investigated by XRD and TPR techniques.XRD characterization showed that CaO was highly dispersed after the calcination of sorbents.Calcium sulfate formed in the desulfurization was decomposed and regenerated to CaO by reacting with CO before the next sulfidation process.Calcium participated in every sulfidation/regeneration cycle and contributed to the enhancement of sulfur capacity.The TPR results showed that the reduction temperature of the sorbent increased with the increase of the content of calcium.Calcium played a role of retarding reduction.Therefore,the addition of calcium oxide additive will benefit the utilization of iron oxide sorbent in strongly reducing atmospheres.

Tailoring the surface structures of iron oxide nanorods to support Au nanoparticles for CO oxidation

Iron oxide supported Au nanomaterials are one of the most studied catalysts for low-temperature CO oxidation.Catalytic performance not only critically depends on the size of the supported Au nanoparticles(NPs)but also strongly on the chemical nature of the iron oxide.In this study,Au NPs supported on iron oxide nanorods with different surface properties throughβ-FeOOH annealing,at varying temperatures,were synthesized,and applied in the CO oxidation.Detailed characterizations of the interactions between Au NPs and iron oxides were obtained by X-ray diffraction,transmission electron microscopy(TEM),and X-ray photoelectron spectroscopy.The results indicate that the surface hydroxyl group on the Au/FeOOH catalyst,before calcination(Au/FeOOH-fresh),could facilitate the oxygen adsorption and dissociation on positively charged Au,thereby contributing to the low-temperature CO oxidation reactivity.After calcination at 200℃,under air exposure,the chemical state of the supported Au NP on varied iron oxides partly changed from metal cation to Au0,along with the disappearance of the surface OH species.Au/FeOOH with the highest Au0 content exhibits the highest activity in CO oxidation,among the as-synthesized catalysts.Furthermore,good durability in CO oxidation was achieved over the Au/FeOOH catalyst for 12 h without observable deactivation.In addition,the advanced identical-location TEM method was applied to the gas phase reaction to probe the structure evolution of the Au/iron oxide series of the catalysts and support structure.A Au NP size-dependent Ostwald ripening process mediated by the transport of Au(CO)x mobile species under certain reaction conditions is proposed,which offers a new insight into the validity of the structure-performance relationship.

Staged reaction kinetics and characteristics of iron oxide direct reduction by carbon

Staged reduction kinetics and characteristics of iron oxide direct reduction by carbon were studied in this work. The characteristics were investigated by simultaneous thermogravimetric analysis, X-ray diffraction（XRD）, and quadrupole mass spectrometry. The kinetics parameters of the reduction stages were obtained by isoconversional（model-free） methods. Three stages in the reduction are Fe2O3→Fe3O4, Fe3O4→Fe O, and Fe O→Fe, which start at 912 K, 1255 K, and 1397 K, respectively. The CO content in the evolved gas is lower than the CO2content in the Fe2O3→Fe3O4stage but is substantially greater than the CO2 contents in the Fe3O4→Fe O and Fe O→Fe stages, where gasification starts at approximately 1205 K. The activation energy（E） of the three stages are 126–309 k J/mol, 628 k J/mol, and 648 k J/mol, respectively. The restrictive step of the total reduction is Fe O→Fe. If the rate of the total reduction is to be improved, the rate of the Fe O→Fe reduction should be improved first. The activation energy of the first stage is much lower than those of the latter two stages because of carbon gasification. Carbon gasification and FexOy reduction by CO, which are the restrictive step in the last two stages, require further study.

Effects of Catalyst and Additive Containing Li, Na, or Ca on Reduction of Iron Oxide/Carbon Composite Pellets

The catalyst containing 0.69% (mass fraction) of Li+, Na+, or Ca2+ were synthesized, and the catalytic effect on the reduction of iron oxide/carbon composite pellets were investigated by comparing with that of additive at 850 degreesC. The effect of the catalyst was greater than that of the additive, it can be considered that catalyst promoted the formation of iron nucleus early on reduction processes of iron oxide/carbon composite pellets. In addition, both effects of catalyst and additive increased after added carbon powder into the pellets, but the extent of increase decreased when the carbon powder exceeded a suitable content (about 4%), this amount is less than that of carbon needed theoretically on the reduction from hematite to iron.

Dissolution kinetics of iron oxides in clay in oxalic acid solutions

Clay samples containing 8.15% iron oxides and 27.49% alumina were leached in oxalic acid. Leaching experiments were per-formed in aqueous solutions of oxalic acid of 0.2-2 mol/L at 40-80 C for up to 90 min. The mixed kinetic mechanism, i.e., t/τ=[（1 2X/3） （1 X）2/3 ]＋b[ 1 （1 X）1/3], seemed to be the most appropriate one to fit the kinetic data of leaching iron oxides contained in clay in the aqueous oxalic acid solutions. The Arrhenius activation energy for leaching in the 1.8 mol/L oxalic acid was found to be 41.035 kJ/mol.

Column adsorption of Cu(Ⅱ) by polymer-supported nano-iron oxides in the presence of sulfate: Experimental and mathematical modeling

Polymer-supported hydrous iron oxides(HFOs) are promising for heavy metals removal from aqueous systems.The ubiquitous inorganic ligands, e.g., sulfate, are expected to exert considerable impacts on pollutants removal by these hybrid sorbents. Herein, we obtained a hybrid sorbent HFO-PS by encapsulating nanosized HFO into macroporous polystyrene(PS) resin. Both batch and column sorption experiments of Cu(Ⅱ) by HFO-PS were carried out in the presence of sulfate. Obviously, the presence of sulfate is favorable for Cu(Ⅱ) sorption onto HFO-PS.The performances of column Cu(Ⅱ) removal were fitted and predicted with Adams–Bohart, Clark, Thomas and BDST models. Thomas model is suggested best-fit to predict the breakthrough curves. Besides, a linear correlation is observed between breakthrough time and column length based on BDST model, which might be useful for predicting the breakthrough time for Cu(Ⅱ) removal by HFO-PS.

Highly Efficient Labeling of Human Lung Cancer Cells Using Cationic Poly-L-lysine-Assisted Magnetic Iron Oxide Nanoparticles

Cell labeling with magnetic iron oxide nanoparticles(IONPs)is increasingly a routine approach in the cellbased cancer treatment.However,cell labeling with magnetic IONPs and their leading effects on the biological properties of human lung carcinoma cells remain scarcely reported.Therefore,in the present study the magnetic c-Fe2O3nanoparticles(MNPs)were firstly synthesized and surface-modified with cationic poly-L-lysine(PLL)to construct the PLL-MNPs,which were then used to magnetically label human A549 lung cancer cells.Cell viability and proliferation were evaluated with propidium iodide/fluorescein diacetate double staining and standard 3-(4,5-dimethylthiazol-2-diphenyl-tetrazolium)bromide assay,and the cytoskeleton was immunocytochemically stained.The cell cycle of the PLL-MNPlabeled A549 lung cancer cells was analyzed using flow cytometry.Apoptotic cells were fluorescently analyzed with nuclear-specific staining after the PLL-MNP labeling.The results showed that the constructed PLL-MNPs efficiently magnetically labeled A549 lung cancer cells and that,at low concentrations,labeling did not affect cellular viability,proliferation capability,cell cycle,and apoptosis.Furthermore,the cytoskeleton in the treated cells was detected intact in comparison with the untreated counterparts.However,the results also showed that at high concentration(400 lg m L-1),the PLL-MNPs would slightly impair cell viability,proliferation,cell cycle,and apoptosis and disrupt the cytoskeleton in the treated A549 lung cancer cells.Therefore,the present results indicated that the PLL-MNPs at adequate concentrations can be efficiently used for labeling A549 lung cancer cells and could be considered as a feasible approach for magnetic targeted anti-cancer drug/gene delivery,targeted diagnosis,and therapy in lung cancer treatment.

Synergism of Pt nanoparticles and iron oxide support for chemoselective hydrogenation of nitroarenes under mild conditions

An efficient and low-cost supported Pt catalyst for hydrogenation of niroarenes was prepared with colloid Pt precursors andα-Fe2O3 as a support.The catalyst with Pt content as low as 0.2 wt%exhibits high activities,chemoselectivities and stability in the hydrogenation of nitrobenzene and a variety of niroarenes.The conversion of nitrobenzene can reach 3170 molconv h^–1 molPt^–1 under mild conditions(30°C,5 bar),which is much higher than that of commercial Pt/C catalyst and many reported catalysts under similar reaction conditions.The spatial separation of the active sites for H2 dissociation and hydrogenation should be responsible for the high chemoselectivity,which decreases the contact possibility between the reducible groups of nitroarenes and Pt nanoparticles.The unique surface properties ofα-Fe2O3 play an important role in the reaction process.It provides active sites for hydrogen spillover and reactant adsorption,and ultimately completes the hydrogenation of the nitro group on the catalyst surface.

In Vitro Targeted Magnetic Delivery and Tracking of Superparamagnetic Iron Oxide Particles Labeled Stem Cells for Articular Cartilage Defect Repair

To assess a novel cell manipulation technique of tissue engineering with respect to its ability to augment superparamagnetic iron oxide particles （SPIO） labeled mesenchymal stem cells （MSCs） density at a localized cartilage defect site in an in vitro phantom by applying magnetic force. Meanwhile, non-invasive imaging techniques were use to track SPIO-labeled MSCs by magnetic resonance imaging （MRI）. Human bone marrow MSCs were cultured and labeled with SPIO. Fresh degenerated human osteochondral fragments were obtained during total knee arthroplasty and a cartilage defect was created at the center. Then, the osteochondral fragments were attached to the sidewalls of culture flasks filled with phosphate-buffered saline （PBS） to mimic the human joint cavity. The SPIO-labeled MSCs were injected into the culture flasks in the presence of a 0.57 Tesla （T） magnetic force. Before and 90 min after cell targeting, the specimens underwent T2-weighted turbo spin-echo （SET2WI） sequence of 3.0 T MRI. MRI results were compared with histological findings. Macroscopic observation showed that SPIO-labeled MSCs were steered to the target region of cartilage defect. MRI revealed significant changes in signal intensity （P0.01）. HE staining exibited that a great number of MSCs formed a three-dimensional （3D） cell ＂sheet＂ structure at the chondral defect site. It was concluded that 0.57 T magnetic force permits spatial delivery of magnetically labeled MSCs to the target region in vitro. High-field MRI can serve as an very sensitive non-invasive technique for the visualization of SPIO-labeled MSCs.

A hydrated amorphous iron oxide nanoparticle as active water oxidation catalyst

Developing efficient water oxidation catalysts(WOCs)with earth‐abundant elements still remains a challenging task for artificial photosynthesis.Iron‐based WOC is a promising candidate because it is economically cheap,little toxic and environmentally friendly.In this study,we found that the catalytic water oxidation activity on amorphous iron‐based oxide/hydroxide(FeOx)can be decreased by an order of magnitude after the dehydration process at room temperature.Thermogravimetric analysis,XRD and Raman results indicated that the dehydration process of FeOx at room temperature causes the almost completely loss of water molecule with no bulk structural changes.Based on this finding,we prepared hydrated ultrasmall(ca.2.2 nm)FeOx nanoparticles of amorphous feature,which turns out to be extremely active as WOC with turnover frequency(TOF)up to 9.3 s^-1 in the photocatalytic Ru(bpy)3^2+‐Na2S2O8 system.Our findings suggest that future design of active iron‐based oxides as WOCs requires the consideration of their hydration status.

Hydrogen-based direct reduction of iron oxide at 700℃:Heterogeneity at pellet and microstructure scales

Steel production causes a third of all industrial CO_(2) emissions due to the use of carbon-based substances as reductants for iron ores,making it a key driver of global warming.Therefore,research efforts aim to replace these reductants with sustainably produced hydrogen.Hydrogen-based direct reduction(HyDR)is an attractive processing technology,given that direct reduction(DR)furnaces are routinely operated in the steel industry but with CH_(4) or CO as reductants.Hydrogen diffuses considerably faster through shaft-furnace pellet agglomerates than carbon-based reductants.However,the net reduction kinetics in HyDR remains extremely sluggish for high-quantity steel production,and the hydrogen consumption exceeds the stoichiometrically required amount substantially.Thus,the present study focused on the improved understanding of the influence of spatial gradients,morphology,and internal microstructures of ore pellets on reduction efficiency and metallization during HyDR.For this purpose,commercial DR pellets were investigated using synchrotron high-energy X-ray diffraction and electron microscopy in conjunction with electron backscatter diffraction and chemical probing.Revealing the interplay of different phases with internal interfaces,free surfaces,and associated nucleation and growth mechanisms provides a basis for developing tailored ore pellets that are highly suited for a fast and efficient HyDR.

Reduction and carburization of iron oxides for Fischer–Tropsch synthesis

The activation of iron oxide Fischer–Tropsch Synthesis(FTS) catalysts was investigated during pretreatment: reduction in hydrogen followed by carburization in either CO or syngas mixture, or simultaneously reduction and carburization in syngas. A combination of different complementary in situ techniques was used to gain insight into the behavior of Fe-based FTS catalysts during activation. In situ XRD was used to identify the crystalline structures present during both reduction in hydrogen and carburization. An increase in reduction rate was established when increasing the temperature. A complete reduction was demonstrated in the ETEM and a grain size dependency was proven, i.e. bigger grains need higher temperature in order to reduce. XPS and XAS both indicate the formation of a small amount of carbonaceous species at the surface of the bulk metallic iron during carburization.

Application of iron oxide anoparticles in neuronal tissue engineering

Since the introduction of nanotechnology, nanoscale materials have developed rapidly and have been applied in various fields including in the pharmaceutical industry, medicine, and tissue engineering. Among a variety of nanomaterials, magnetic iron oxide nanoparticles （IONPs） have been intensively investigated for numerous in vivo applications such as gene and drug delivery, diagnostics, cell labeling and sorting. Compared to nanoparticles made from other materials, IONPs have several additional unique applications due to their magnetic properties, for example, magnetic cell separation,