The Preparation of Perovskite Nano Powder by Sol-gel from DTPA and the Mechanism of Thermal Decomposition

Dy0.8Sr0.2FeO3 nano powder, a synthetic oxide, is made by sol-gel method from metal nitrate and diethylenetriaminepentaacetic acid (DTPA), and the processing parameters are optimized. The process of the preparation, thermal decomposition and the property of the powder are studied by TG-DTA, IR, TEM, and XRD. The diameter of the average grain is about 70 nm. This new technique can be used in the preparation and the studying of na'no materials in the complex oxide system.

Manufacture Process of 8Y_2O_3 Stabilized ZrO_2 from Nano Powders

The manufacture process of 8mol% Y-2O-3 stabilized ZrO-2(YSZ) from nano powders, including the forming and sintering stages, was studied. During the forming process of YSZ powders, the relative density of YSZ increases lineally with the forming press,and the sintering linear shrinkage of YSZ to the forming press compiles to the parabola trend. When the forming press exceeding 500MPa, the samples with lower shrinkage and high density were obtained. The sintering temperature of YSZ decreases greatly because of the small size and high active surface of YSZ powders. As a result, the beginning sintering temperature of YSZ made in the experiment is as low as 825℃, and the end sintering temperature is 1300-1350℃. The relative density of YSZ ceramic by solid sintering at 1300-1350℃ is more than 97%, with little and small pores in the uniform microstructure.

Structure,room-temperature magnetic and optical properties of Mn-doped TiO_2 nano powders prepared by the sol-gel process

TiO2 nano powders with Mn concentration of 0 at%-12 at% were synthesized by the sol-gel process, and were annealed at 500 ℃ and 800 ℃ in air for 2 hrs. X-ray diffraction （XRD） measurements indicate that the Mn-TiO2 nano powders with Mn concentration of 1 at% and 2 at% annealed at 500 and 800 ℃ are of pure anatase and rutile, respectively. The scanning electron microscope （SEM） observations reveal that the crystal grain size increases with the annealing temperature, and the high resolution transmission electron microscopy （HRTEM） investigations further indicate that the samples are well crystallized, confirming that Mn has doped into the TiO2 crystal lattice effectively. The room temperature ferromagnetism, which could be explained within the scope of the bound magnetic polaron （BMP） theory, is detected in the Mn-TiO2 samples with Mn concentration of 2 at%, and the magnetization of the powders annealed at 500 ℃ is stronger than that of the sample treated at 800 ℃. The UV-VIS diffuse reflectance spectra results demonstrate that the absorption of the TiO2 powders could be enlarged by the enhanced trapped electron absorption caused by Mn doping.

Direct synthesis of hollow polyhedral ceria nano powders via a template-free mixed solvothermal route

Novel mono-dispersed hollow polyhedral ceria nano powders with the average particle size of 250 nm were directly synthesized via a simple template-free mixed solvothermal method by using water-ethanol as the solvent. The formation of such hollow structure with the regular polyhedral particle shape was based on a solvent-controlled Ostwald ripening coupled self-templating process. The mixed solvent promoted the formation of the regular solid particles at the beginning of solvothermal reaction and drove the Ostwald ripening as the reaction went on. Owing to the Ostwald ripening and self-assembly of nano crystallites, ceria nano particles converted into the hollow structures with regular polyhedral shape during the solvothermal process just by increasing solvothermal reaction time. The as-synthesized hollow ceria nano powders exhibited strong absorptions in the UV-vis spectrum and the evaluated energy band gaps increased according to the shape evolution and size decrease of the nano particles, which demonstrated obvious blue shift effects.

Relation between powder size and electrolyte properties in nano YSZ system

YSZ (yttria stabilized zirconia) electrolyte properties made from different sizes of nano powders were investigated. As a result, the sample marked KD with the smallest size (10 nm) of first particles and the sample marked TH with narrow distribution and the smallest median diameter Mmed of 0.49μm have the best sintering properties and the highest electrical conductivity. There is a very well correlation between the density and the electrical conductivity of YSZ, that is, the samples with a higher density have a higher electrical conductivity. The area resistance of YSZ electrolyte made in the experiment, such as TH of 0.483 Ω·cm2, is much lower than that of the sample D of 1.300 Ω·cm2 made in Germany at 850℃. The complex resistance of YSZ electrolyte made in the experiment at the grain, grain boundary and electrode in the range of 300-750℃ decreases greatly compared to the sample made in Germany by shown in the complex impedance plot.

One-pot three-component synthesis of α-amino nitriles catalyzed by nano powder TiO_2 P 25

A simple and efficient method has been developed for the synthesis ofα-amino nitriles from aldehydes,amines and trimethylsilyl cyanide（Me_3SiCN） in the presence of a catalytic amount of cyanuric acid at room temperature.

Synthesis of Y_2O_3 Nano-Powder from Yttrium Oxalate under Ambient Temperature

High purity Y_2O_3 nano-powders was synthesized directly from solution ofindustrial YCl_3 by method of oxalate precipitation through super-micro-reactors made by complexnon-ionic surfactant. The purity and diameter of Y_2O_3 particles were controlled by such processingparameters as concentration of YCl_3 and oxalic acid and complex non-ionic surfactant etc. TEMphotomicrographs show that Y_2O_3 particles are spherical in shape, with an average diameter of lessthan 30 nm. Test results certify that the purity and particle diameter as well as the dispersion ofY_2O_3 nano-powder depend on the concentrations of YCl_3, oxalic acid and complex non-ionicsurfactant. The optimum ranges of the concentrations for YCl_3 and complex non-ionic surfactant whenthe diameter of Y_2O_3 particles is smaller than 100 nm are 0.43 ～1.4 mol ? L^(-1) and0.031～0.112 mol·L^(-1) respectively, while the mass fraction range of oxalic acid is 10% ～18% .The purity of Y_2O_3 nano-powder tested by ICP-AES analysis is 99.99% .

Preparation of Nano-sized Zirconium Carbide Powders through a Novel Active Dilution Self-propagating High Temperature Synthesis Method

High quality nano-sized zirconium carbide （ZrC） powders were successfully fabricated via a developed chemical active dilution self-propagating high-temperature synthesis （SHS） method assisted by ball milling pretreatment process using traditional cheap zirconium dioxide powder （ZrO2）, magnesium powder （Mg） and sucrose （C12H22Oll） as raw materials. FSEM, TEM, HRTEM, SAED, XRD, FTIR and Raman, ICP- AES, laser particle size analyzer, oxygen and nitrogen analyzer, carbon/sulfur determinator and TG-DSC were employed for the characterization of the morphology, structure, chemical composition and thermal stability of the as-synthesized ZrC samples. The as-synthesized samples demonstrated high purity, low oxygen content and evenly distributed ZrC nano-powders with an average particle size of 50nm. In addition, the effects of endothermic rate and the possible chemical reaction mechanism were also discussed.

DIELECTRIC PROPERTIES OF NANO Si/C/N COMPOSITE POWDER AND NANO SiC POWDER AT HIGH FREQUENCIES AND MICROSTRUCTURE CHARACTERIZATION

The dielectric properties of nano Si/C/N composite powder and nano SiC powder at high frequencies have been studied. The nano Si/C/N composite powder and nano SiC powder were synthesized from hexamethyldisilazane ((Me 3Si) 2NH) (Me:CH 3) and SiH 4 C 2H 2 respectively by a laser induced gas phase reaction. The complex permittivities of the nano Si/C/N composite powder and nano SiC powder were measured between 8 2GHz and 12 4GHz. The real and imaginary parts of the complex permittivities of nano Si/C/N composite powder are much higher than those of nano SiC powder. The SiC microcrystalline in the nano Si/C/N composite powder dissolved a great deal of nitrogen. The local structure around Si atoms changed by introducing N into SiC. Carbon atoms around Si were substituted by N atoms. So charged defects and quasi free electrons moved in response to the electric field, diffusion or polarization current resulted from the field propagation. The high ε″and loss factor tgδ(ε″/ε′) of Si/C/N composite powder were due to the dielectric relaxation.

Progress on grain growth dynamics in sintering of nano-powders

Nanostructured materials, characterized by an ultrafine grain size, have stimulated much research interest by virtue of their unusual mechanical, electrical, optical, and magnetic properties. In this paper, the sintering process of nano-powders were reviewed, to which sintering of the traditional materials compared. The microstructural development, i.e., grain growth and densification during sintering as well as the mechanism of crystal surface diffusion and boundary migration were analyzed, and the dynamic models on sintering process were summarized by the relationship of grain growth and pores size, interface diffusion, densification rate, and sintering temperature. Finally, the research tendency of this major on the basis of above models was discussed.

Fabrication and Characterization of Nano Silver Powder Prepared by Spray Pyrolysis

Silver powder was fabricated by spray pyrolysis, using 2%-20% AgNO3 solution, 336-500 mL/h flux of AgNO3 solution, 0.28-0.32 MPa flux of carrier gas and in the 620-820 ℃ temperature range. The effects of furnace set temperature, concentration of AgNO3 aqueous solution, flux of AgNO3 aqueous solution as well as carrier gas on the morphology and particle size distribution of silver powder, were investigated. The experimental results showed that with the high concentration of AgNO3 aqueous solution, the average grain size of silver decreased with the increasing of furnace set temperature. But the gain size distribution was not homogenous, the discontinuous grain growth occurred. With the low concentration of AgNO3 aqueous solution, the higher furnace set temperature made the nano sliver grains sintered together to grow. Nano silver powder about 100 nm was fabricated by spray pyrolysis, using 2wt% AgNO3 solutions, 336 mL/h flux of AgNO3 aqueous solution, 0.32 MPa flux of carrier gas at 720 ℃ furnace set temperature.

Preparation and Characterization on Nano- Sized Barium Titanate Powder Doped with Lanthanum by Sol-Gel Process

The nano-sized BaTiO3:La3+ powders were prepared by sol-gel process using butyl phthalate, barium acetate and lanthanum oxide as raw material, and these samples were tested by means of TG-DTA, XRD and SEM. The results indicate that with the annealing temperature and the doped concentration rising, the powders' particle sizes will increase and decrease respectively. When annealing temperature is 900℃and doped concentration is 7%, the phase is cubic without other phases, and the particle size of power is 43 .34 nm.

ITO nano-powders prepared by microwave-assisted co-precipitation in aqueous phase

By using microwave-assisted co-precipitation in aqueous phase, adding surface activation agent PEG-6000 into the mixture of InCl3 solution and SnCl4 solution, and dropping the ammonia solution with the density (volume ratio) of 1-0 to 1-4, ITO precursor was prepared at different reaction system temperatures of 35 ℃-85 ℃, then ITO nano-powder was obtained after it was calcinated at 800 ℃ for 1 h. The morphology of ITO nano-powder was characterized by SEM and its electrical conductivity was determined by conductivity meter. The effects of different temperatures and ammonia concentration in microwave-assisted reaction system on its morphology and electric conductivity were discussed. The experimental results indicate that with the dilution of the ammonia solution or the rise of reacting system temperature, the morphology of ITO particles is transformed from spherical to rod-like one with the decline of its electric conductivity. And the electric conductivity of ITO nano-powders with spherical morphology is higher than that of ITO nano-powders with rod-like morphology.

PREPARING NANO-CRYSTALLINE La DOPED WC/Co POWDER BY HIGH ENERGY BALL MILLING

The La doped WC/Co powder was prepared by high energy ball milling. The changes of crystal structure, micrograph and defect of the powder were investigated by means of XRD (X-ray diffraction), SEM (scanning electron microscope) and DTA (differential thermal analysis). The results show that adding trace La element into carbides is effective to minish the grain size of WC/Co powder. The La doped carbides powder with grain size of 30nm can be obtained after 10h ball milling. The XRD peak of Co phase disappeared after 20h ball milling, which indicated solid solution (or secondary solid solution) of Co phase in WC phase. The La doped powder with grain size of 10nm is obtained after 30h ball milling. A peak of heat release at the temperature of 470℃ was emerged in DTA curve within the range of heating temperature, which showed that the crystal structure relaxation of the powder appeared in the process of high energy ball milling. After consolidated the La doped WC/Co alloy by high energy ball milling exhibits ultra-fine grain sizes and better mechanical properties.

Synthesis of Neodymium-Doped Yttrium Aluminum Garnet (Nd∶YAG) Nano-Sized Powders by Low Temperature Combustion

The homogeneously dispersed, less agglomerated (Nd0.01Y0.99)3Al5O12 nano-sized powders were synthesized by the low temperature combustion (LCS), using Nd2O3, Y2O3, Al(NO3)3·9H2O, ammonia water and citric acid as starting materials. This method effectively solves the problems caused by solid-state reaction at high temperature and hard agglomerates brought by the chemical precipitation method. The powders were characterized by TG-DTA, XRD, FT-IR, TEM respectively and the photoluminescence (PL) spectra of (Nd0.01Y0.99)3Al5O12 green and sintered ceramic disks were measured. The results show that the forming temperature of YAG crystal phase is 850 ℃ and YAP crystal phase appearing during the calcinations transforms to pure YAG at 1050 ℃. The particle size of the powders synthesized by the LCS is in a range of 20～50 nm depending on the thermal treatment temperatures. The effectively induced cross section (σin) with the value 4.03×10-19 cm2 of (Nd0.01Y0.99)3Al5O12 ceramics is about 44% higher than that of single crystal.

Synthesis and Luminescence of Nano Fluorescent Powder of Y_4Al_2O_9:Eu^(3+)

Nano fluorescent powder of Y 4Al 2O 9:Eu 3+ was synthesized by sol gel method.The XRD shows that the product prepared at 900℃ is pure phase Y 4Al 2O 9:Eu 3+ .The Y 4Al 2O 9 powder is nano size crystal testified by BF and ED analysis of TEM.The grain diameter of Y 4Al 2O 9 is in the range between 20 and 50nm,and its average is 30nm.The luminescent spectra show that Eu 3+ ious occupy two kinds of sites in Y 4Al 2O 9 crystal lattice.One is in the strict inversion center,and the other is in off lying inversion center.When excited with UV light (λ=254nm),Y 4Al 2O 9:Eu 3+ exhibits an orange emission band at λ=590nm due to the 5D 0→ 7F 1 transition and a red emission band at λ=610nm due to 5D 0→ 7F 2 transition.

Synthesis and Characterization of Nano-sized Boron Powder Prepared by Plasma Torch

Hydrogen thermal plasma jet was employed to prepare nano-sized boron powder with hydrogen reduction of BCI3. The maximum yield of nano-sized boron powders was about 50% with the operational conditions of H2/BCl3 of 4.5：1, total feed of 4.9 m3/h, and plasma power of 25 kW. The samples were analyzed by X-ray diffraction （XRD）, field emission scanning electron microscopy （FE-SEM）, and inductively coupled plasma - mass spectrometry （ICP-MS）, inductively coupled plasma - atomic emission spectrometry （ICP-AES）, inductive combustion infrared absorption （ICIA） and infrared thermal conductivity of oxygen and nitrogen analyzer （ITCA）. The results show that the boron powders have different crystal structures with higher dispersion and purity. The average diameter is about 50 nm, and the purity is 90.29% or so. This new technology can use simple process to produce high quality boron powders, and is feasible for industrial production.

Preparation of tetragonal CaO-ZrO_2 nano-powder by chemical coprecipitation method

With zirconium oxychloride, nitrate of lime and ammonia as raw materials, nano powder of CaO ZrO 2 was prepared by chemical coprecipitation method. By use of azeotropic distillation processing, chemical coprecipitation precursor was obtained. Phase transformation of the precursor was observed at the temperature of 593.81 ℃ and 1 234.56 ℃ respectively with DTA analyses. Phase structure was analyzed through XRD and Raman spectra. The average particle size of tetragonal zirconium oxide powder was 9.8 and 43.7 nm after calcination at 600 and 1 100 ℃ respectively which was tested by TEM and BET analyses. Furthermore, the influences of the doping of nitrate of lime and the average particle size of zirconium oxide on the stability of tetragonal zirconium oxide were also discussed.

Injection molding of nano structured 90W-7Ni-3Fe alloy powder prepared by high energy ball milling

Blended elemental 90W 7Ni 3Fe (mass fraction, %) powder was mechanically alloyed in a planetary ball mill. Nano crystalline grains were obtained after 10 h milling. The nano structured powder was processed to full density by metal injection molding approach. Compacts from the optimal powder binder mixture were studied for molding and sintering behaviors. Milling significantly increases the maximum powder loading and homogeneity of the feedstock, and enhances the sintering densification process. When solid state sintered at 1 350～1 450 ℃, the alloy shows very fine grains (～3 μm), high tensile strength (>1 130 MPa) and almost no distortion. [

Powder Quartz/Nano-TiO2 Composite: Mechanochemical Preparation and Photocatalytic Degradation of Formaldehyde

Powder quartz(PQ)/nano-TiO2composite was prepared by a mechanochemical method. Based on as-prepared PQ/nano-TiO2composite, we prepared interior paints and investigated the degradation efficiency of formaldehyde(DEF). Scanning electron microscopy showed that nano-TiO2got well dispersed by the adding of PQ. Thermogravimetric analysis indicated that the mass ratio of 4:1 was a relatively good proportion for the most production of PQ/nano-TiO2composite. Fourier transform-infrared spectrometry showed that the peak position of Ti-O-Si bond varied with the milling time. At the early stage, no characteristic peak of Ti-O-Si bond was observed, while at the later stage, new peaks at 902 cm-1and 937 cm-1appeared. Meanwhile, PQ/nano-TiO2composite-based interior paint exhibited significant DEF of 96.3% compared to that consisting of sole nanoTiO2of 92.0% under visible light illumination. As an abundant mineral resource, PQ would make interior paints with HCHO purifying effect much more efficient and cheaper.