Impact Resistance of Reactive Powder Concrete

The impact behaviour of three types of reactive powder concretes （RPC） was studied using the split Hopkinson press bar （SHPB） testing method. These RPC were prepared with steel fiber volume fraction of 0%, 3%, and 4%, respectively. The stress-strain relationship, strain rate sensitivity threshold value, dynamic strength increase factor, modulus of elasticity and failure pattern of these RPC specimens subjected to impact load were investigated. From the tests, the strain rate sensitivity threshold value of 50 s-1 was obtained. The experimental results showed that when the strain rate increased from the threshold value to 95 s-1, the maximum stress of RPC increased by about 20% and the modulus of elasticity of RPC increased by about 30%. The failure pattern of RPC specimens with steel fiber reinforcement was very different from that of the RPC matrix specimen when subjected to impact loading. Under similar impact loading rate, cracks developed in the steel fiber reinforced RPC specimens, whilst the RPC matrix specimens were broken into small pieces.

Size effect on compressive strength of reactive powder concrete

In this paper the coefficient and law of the size effect of RPC were studied through experiments and theoretical analysis. The size-effect coefficients for the compressive strength of RPC are deduced through experiments.They indicate that RPC without fiber behaves quite the same as normal or high strength concrete.The size effect on compressive strength is more prominent in RPC containing fiber.Bazant's size effect formula of compressive strength applies to RPC.A formula is given to predict the compressive strength of cubic RPC specimens 100 mm on a side where the fiber dosage ranges from 0-2%.

EXPERIMENTAL AND NUMERICAL STUDIES ON DYNAMIC COMPRESSIVE BEHAVIOR OF REACTIVE POWDER CONCRETES

Split Hopkinson pressure bar （SHPB） technique is used to determine the dynamic strength of reactive powder concretes （RPCs） with different steel-fiber contents. Two types of pulse shapers with different thicknesses are considered to reduce the high-frequency-oscillation effect and achieve a nearly constant strain rate over a certain deformation range. It is known that the compressive strength of concrete-like materials is hydrostatic-stress-dependent, and the apparent dynamic strength enhancement comes from both the effects of the hydrostatic stress and strain rate. In order to differentiate them, numerical method is used to calculate the contribution of the hydrostatic stress, and then the genuine strain-rate effect on dynamic compressive strength of RPCs is determined. In addition, the effect of steel-fibers on dynamic strength and failure mode of RPCs is discussed.

Preparation of Reactive Powder Concrete Using Fly Ash and Steel Slag Powder

To decrease the cement and SF content of RPC by using ultra-fine fly ash （UFFA） and steel slag powder （SS）, the effect of these mineral admixtures on compressive strength of RPC were investigated. The experimental results indicate that the utilization of UFFA and SS in RPC is feasible and has prominent mechanical performance. The microstructure analysis （SEM and TG-DTG-DSC） demonstrated that the excellent mechanical properties of RPC containing SS and UFFA were mainly attributed to the sequential hydration filling effect of the compound system.

Shaped charge penetration into high-and ultrahigh-strength Steel-Fiber reactive powder concrete targets

Experiments on shaped charge penetration into high and ultrahigh strength steel-fiber reactive powder concrete(RPC) targets were performed in this paper.Results show that the variation of penetration depth and crater diameter with concrete strength is different from that of shaped charge penetration into normal strength concrete(NSC).The crater diameter of RPC is smaller than that of NSC penetrated by the shaped charge.The jet particles are strongly disturbed and hardly reach the crater bottom because they pass through the narrow channel formed by jet penetration into the RPC.The effects of radial drift velocity and gap effects of jet particles for a shaped charge penetration into RFC target are discussed.Moreover,a theoretical model is presented to describe the penetration of shaped charge into RPC target.As the concrete strength increases,the penetration resistance increases and the entrance crater diameter decreases.Given the drift velocity and narrow crater channel,the low-velocity jet particles can hardly reach the crater bottom to increase the penetration depth.Moreover,the narrow channel has a stronger interference to the jet particles with increasing concrete strength;hence,the gap effects must be considered.The drift velocity and gap effects,which are the same as penetration resistance,also have significant effects during the process of shaped charge penetration into ultrahigh-strength concrete,The crater profiles are calculated through a theoretical model,and the results are in good agreement with the experiments.

Durability and Micro-structure of Reactive Powder Concrete

Durability of traditional reactive powder concrete （RPC） with rich cement and high volume of fly-ash reactive powder concrete （FRPC） were studied. The X-diffraction and scanning electron microscope （SEM） measurement was imployed to analyze the microstructure. The results show that both types of RPC have higher compressive strength, less volume shrinkage ratio and better carbonation-, chloride-, freezing-resistances than the conventional concrete. The results of X-diffraction indicate that they basically have C-S-H as the main composition without Ca（OH）2 crystal and ettringite. SEM results show that hydration products of FRPC is mainly Ⅲ-C-S-H which is piled up closely like densely arranged stone body and it has very compacted structure, in addition, Ca/Si ratio of C-S-H gel is lower than 1.5.

Mechanical Properties of Reactive Powder Concretes Produced Using Pumice Powder

We examined the applicability of the pumice aggregate on the concrete formed by considering the reactive powder concrete mixture ratios, for the rigid superstructure concrete road pavement and building construction. The natural pumice aggregate in fibrous and non-fibrous concrete samples was used in the production of concrete by fracturing in 0.1-0.6 mm dimensions in rotor mill. The concreted formed in this way is named after the pumice powder concrete(PPC). The PPC samples produced were taken 7 days as 20 ℃ standard water cure, 28 days as 20 ℃ standard cure and 9 different types of combined cures. The combined cures were applied different temperatures in different durations. PPC samples were subjected to some pressure and flexural tests at the end of the standard water and combined cures. The highest compressive and flexural strengths of PPC samples were obtained after the combined cures: 3 days in 20 ℃ as standard water curing + 2 days in 180 ℃ in drying-oven. The highest compressive strength of PPC samples without any fiber was found to be 47.27 MPa, as for the highest flexural strength, it is found to be 5.23 MPa, in the end of the study. The highest compressive strength of fibrous PPC samples was 51.12 MPa, while flexural strength was 6.57 MPa.

Strength and Toughness of Steel Fibre Reinforced Reactive Powder Concrete Under Blast Loading

The blast resistance of structures used in buildings needs to be investigated due to the increased threat of a terrorist attack. The damage done by Composition B or Powergel to steel fibre reinforced reactive powder concrete （SFRPC） panels and ordinary reinforced concrete （RC） panels of equivalent static flexural strength is compared. A 0. 5 kg charge was detonated at a distance of 0. 1 m from the 1. 3 m × 1. 0 m × 0. 1 m （thick） panels, which were simply supported and spaning 1.3 m. Dynamic displacement measurements, high-speed video recording and visual examination of the panels for spall and breach were undertaken. The SFRPC panels withstood the bare charge blast better than the reinforced ordinary concrete panels. Neither type of panel was breached using a O. 5 kg charge, The RC panel exhibited more spalling when Composition B was used. Under successive Composition B loading conditions, the RC panel was breached. In comparison the SFRPC panel was not breached. Exposure to fragmenting charge loading conditions confirmed these performance differences between the SFRPC panel and the reinforced ordinary concrete panel.

Preparation and Dynamic Tensile Behavior of C200 Green Reactive Powder Concrete

A new type of green reactive powder concrete (GRPC) with compressive strength of 200 MPa is prepared by utilizing composite mineral admixtures, natural fine aggregates, and short and fine steel fibers. The quasi-static mechanical properties (mechanical strength, toughness, fracture energy and interfacial bonding strength) of GRPC specimens, cured in three different types of regimes, are investigated. The experimental results show that the mechanical properties of the C200 GRPC made with the powder binders that is composed of 40% of Portland cement, 25% of ultra fine slag, 25% of ultra fine fly ash and 10% of silica fume are better than the others'. The corresponding compressive strength, flexural strength and fracture energy are more than 200 MPa, and 30 000 J/ m2 respectively. The dynamic tensile behavior of the C200 GRPC is also investigated through the split Hopkinson pressure bar (SHPB) according to the spalling phenomenon. The dynamic testing results demonstrate that strain rate has an important effect on the dynamic tensile behavior of GRPC. With the increase of strain rate, its peak stress and relevant strain increase. The GRPC exhibits an excellent strain ratio stiffening effect under the dynamic tensile load with high strain ratio, resulting in a significant change of the fracture pattern.

Corrosion Behavior of Steel Fibers in Reactive Powder Concrete with High Volume of Mineral Admixtures

The corrosion behavior and the effects of temperature on critical chloride content (Ccrit) of steel fibers in RPC were analyzed by a pH meter, ion chromatography, mercury intrusion porosimetry (MIP), and electrochemical techniques. It was found that the suspension pH value, the chloride binding capacity, and the total porosity of RPC were lower than those of high-performance concrete (HPC). The pore structure of RPC mainly consisted of gel pores. The Ccrit values of steel fibers in RPC and HPC at 20 ℃ were 1% and 2%, respectively. When the temperature reached 50 ℃, the Ccrit value of steel fibers in HPC decreased significantly, whereas it remained unchanged in RPC. The corrosion rate of corroded fibers in both RPC and HPC started to decrease with the rise in temperature.

Analysis on plastic properties of reactive powder concrete continuous beams reinforced with GFRP bars

To study the plastic properties of reactive powder concrete continuous beams reinforced with GFRP bars,the calculation programs for moment redistribution coefficients are prepared by using nonlinear analysis methods such as moment-curvature,conjugate beam method and so on. By comparing the test results of existed FRP bars reinforced concrete continuous beams with simulation results,the accuracy of the calculation program is verified. Then 18 simulated GFRP bars reinforced reactive powder concrete continuous beams are selected whose change parameters are reinforcement ratio of mid-span and middle support. Through the nonlinear analysis of simulated beams,moment redistribution coefficients under mid-span concentrated loads,one-third point loads and uniformly distributed loads are obtained respectively. Thus the formula of moment redistribution coefficients is obtained by fitting moment redistribution coefficients and factors. The results show that the reactive powder concrete continuous beams reinforced with GFRP bars have good plastic properties.

Surface Morphology of Reactive Powder Concrete Containing Soil

Recent studies have revealed that concrete can be used as a media to contain As （arsenic） removed from drinking water. Concrete, which is a composite material, has been effective in solidifying hazardous wastes and contaminated soils. A research project was conducted to study the effects of uncontaminated soil and arsenic contaminated soil on the microstructure of concrete to qualitatively define the mechanisms of the encapsulation of soils containing inorganic material such as arsenic by application of solidification/stabilization technique. This research paper focused on studying the surface morphology of RPC （reactive powder concrete） containing soil.

Compressive and Flexural Strength of Recycled Reactive Powder Concrete Containing Finely Dispersed Local Wastes

The main objective of this experimental study is to investigate the behavior of Recycled Reactive Powder Concrete (RRPC) developed from finely dispersed local waste raw materials. In this study, RRPC was developed by utilizing local wastes (finely dispersed waste glass powder, waste fly ash and waste ceramic powder) together with Portland cement, fine sand, admixture, steel fibers and water through full replacement of silica fume as well as quartz powder for sustainable construction practice. In this study, all raw materials for making RRPC were analyzed for X-Ray Fluorescence analysis. For sustainability of local construction works, this study employed standard curing method at ambient temperatures instead of steam curing at higher temperatures. Moreover, hand mixing was used throughout the study. To evaluate the structural performances of the developed RRPC mixes, compressive and flexural strengths of RRPC were investigated experimentally and compared with the control mix. The experimental results indicated that replacing the silica fume fully by finely dispersed local waste glass powder (GP) and fly ash (FA) is a promising approach for local structural construction applications. Accordingly, a mean compressive strength of 62.9 MPa and flexural strength of 8.8 MPa were developed using 50% GP-50% FA at 28thdays standard curing. In this study, 17.56% larger compressive strength and 30.6% flexural strength improvements were observed as compared to the control mix.

Investigating the influence of gamma ray energies and steel fiber on attenuation properties of reactive powder concrete

The effect of gamma ray energies and volume ratio of micro steel fiber(1 and 1.5%) on attenuation properties of reactive powder concrete(70 MPa compressive strength) was investigated. Different characteristics have been considered such as linear attenuation coefficient,mass attenuation coefficient, and half-value thickness.Sodium iodide crystal with a gamma ray spectrometer and collimated beam of gamma ray has been implemented to perform the experimental test. Three sources(Cs-137, Co-60, and Bi-207) with energies of(0.662, 1.17 1.33, 0.569,and 1.063) MeV were adopted in the test. The results obtained indicated that mass attenuation coefficient is proportioned inversely with gamma ray energies and directly with a volume ratio of micro steel fiber. The linear attenuation coefficient and half-value thickness of the tested samples have been calculated and discussed. The obtained results showed that increasing the volume ratio of steel fiber has modified the adequacy of the reactive powder concrete as a shielding element since it increases the density and reduces the half-value thickness.

The Effect of Various Polynaphthalene Sulfonate Based Superplasticizers on the Workability of Reactive Powder Concrete

A superplasticizer is a type of chemical admixture used to alter the workability(viscosity)of fresh concrete.The workability of fresh concrete is often of particular importance when the water-to-cement(w/c)ratio is low and a particular workability is desired.Reactive Powder Concrete(RPC)is a high-strength concrete formulated to provide compressive strengths exceeding 130MPa and made of primarily powders.RPC materials typically have a very low w/c,which requires the use of a chemical admixture in order to create a material that is easier to place,handle and consolidate.Superplasticizer are commonly used for this purpose.Superplasticizers are developed from different formulations,the most common being Polycarboxylate Ether(PCE),Polymelamine Sulfonate(PMS),and Polynaphthalene Sulfonate(PNS).This study investigates the effect of various PNS based superplasticizers on the rheological performance and mechanical(compressive strength)performance of a RPC mixture.Six distinctive types of PNS based superplasticizers were used;three of various compositional strengths(high,medium,low range)from a local provider,and three of the same compositional strengths(high,medium,low)from a leading manufacturer.The properties investigated were the individual superplasticizers’viscosity,the concrete workability,determined through a mortar spread test,the concrete viscosity,and the compressive strength of the hardened RPC mixtures measured at 7,14,and 28 days.Two separate RPC mixtures were prepared,which contained two different water-to-cementitious ratios,which consequently increases the dosage of superplasticizer needed,from 34.8L/m3 to 44.7L/m3.The results show that the name brand high range composition produced the overall highest spread,lowest viscosity,and a highest compressive performance.However,the local provider outperformed the name brand in the mid and low range compositions.Lastly,the rheology assessment also confirmed that the name brand high range,and RPC fabricated with the name brand high range,developed the lowest viscosities.

Stress-strain relationship for reactive powder concrete with recycled powder under uniaxial compression

The recycled powder(RP)from construction wastes can be used to partially replace cement in the preparation of reactive powder concrete.In this paper,reactive powder concrete mixtures with RP partially replacing cement,and natural sand instead of quartz,are developed.Standard curing is used,instead of steam curing that is normally requested by standard for reactive powder concrete.The influences of RP replacement ratio(0%,10%,20%,30%),silica fume proportion(10%,15%,20%),and steel fiber proportion(0%,1%,2%)are investigated.The effects of RP,silica fume,and steel fiber proportion on compressive strength,elastic modulus,and relative absorption energy are analyzed,and theoretical models for compressive strength,elastic modulus,and relative absorption energy are established.A constitutive model for the uniaxial compressive stress-strain relationship of reactive powder concrete with RP is developed.With the increase of RP replacement ratio from 0% to 30%,the compressive strength decreases by 42% and elastic modulus decreases by 24%.

RPC外包方钢管混凝土柱轴压受力性能研究

为了研究活性粉末混凝土(Reactive powder concrete,RPC)外包方钢管混凝土柱的轴压受力性能,以RPC厚度和长细比为参数,对6根构件开展轴压试验研究,探讨该类组合柱的破坏模式、受力机理、套箍效应和承载力。试验结果表明:外层RPC可为内部方钢管混凝土柱提供较强的约束力,在受力后期套箍效应凸显。随着RPC厚度的增加,组合柱的承载力逐渐提高;随着组合柱长细比的增大,虽然其弹性刚度和承载力逐渐降低,但延性改善。采用ABAQUS软件建立RPC外包方钢管混凝土柱的有限元模型,分析RPC强度、RPC厚度、钢管强度等级、含钢率、内部混凝土强度和长细比等参数对组合柱承载力的影响规律,可得方钢管混凝土柱发挥系数的变化幅值为0.78~1.01。在试验研究、有限元参数分析和理论探讨的基础上,借鉴钢管混凝土结构技术规范,提出了RPC外包方钢管混凝土轴压短柱和长柱的承载力简化计算方法,公式计算值与已有数据样本吻合良好。

RPC应力-应变曲线系数与塑性损伤因子无量纲化计算模型研究

为了方便活性粉末混凝土(Reactive Powder Concrete,RPC)等效矩形应力图系数与塑性损伤因子的计算与取值,对RPC应力-应变曲线系数与塑性损伤因子的计算模型进行了理论研究。通过对现有的计算方法进行无量纲化转化,推导了决定计算模型的四个原函数条件;对一个实际的应力-应变关系进行了计算,将得到的结果进行了分析;并对受弯矩形梁非极限状态下截面内力和力矩的推定计算进行了演示。针对应力-应变关系式含有非整次有理分式的情况提出了曲线拟合方法;研究了拟合次数、拟合区间和拟合函数类型对拟合精度与稳定性的影响。比较了4种典型的RPC本构模型在同种材料下的应力-应变曲线系数与损伤因子取值模型曲线,结果显示:拟合曲线得到的取值模型与其他原始曲线得到的取值模型在曲线上具有较高的相似度,证明了曲线拟合方法的准确可靠性;最后给出了一种RPC受压应力-应变曲线系数与塑性损伤因子无量纲化取值模型。

碳纤维和EPS颗粒对RPC性能的影响

研究了不同掺量(0、0.2%、0.3%、0.4%、0.5%、1.0%)的碳纤维(CF)全取代钢纤维(SF)对活性粉末混凝土(RPC)工作性的影响,优选出了适宜CF掺量;在此基础上,研究了EPS颗粒掺量(10%、20%、30%、40%、50%)对掺CF的RPC(CF-RPC)工作性、力学性能、干表观密度和导热系数的影响,并与同EPS颗粒掺量条件下掺SF的RPC(SF-RPC)性能进行了对比。结果表明:CF的适宜掺量为0.3%;随着EPS颗粒掺量的增加,CF-RPC试件的扩展度先增大后减小,抗压强度、抗折强度、干表观密度和导热系数均降低,韧性提升;与掺EPS的SF-RPC试件相比,掺EPS的CF-RPC试件的抗压强度较低,但韧性较好,干表观密度和导热系数均较低。

矿物掺合料在活性粉末混凝土(RPC)中应用研究

矿物掺合料作为一种重要材料在混凝土中应用,为研究矿物掺合料对活性粉末混凝土(RPC)性能影响,以及应用的可行性,将矿物掺合料复配到C120 RPC中,研究对RPC的性能影响规律及得到最佳胶凝材料体系。结果表明:(1)最小基本需水量、标准稠度需水量试验得到矿物掺合料最佳掺量,水泥∶超细矿粉∶硅灰∶粉煤灰=0.7∶0.1∶0.1∶0.1。(2)超细矿粉对RPC 3 d、7 d强度影响明显,分别最大提高6 MPa、13.5 MPa;硅灰对RPC 28 d强度影响明显,最大提高2.2 MPa;粉煤灰对RPC扩展度影响明显,最大提高71 mm。(3)研究确定RPC中四元胶凝体系,即水泥∶超细矿粉∶硅灰∶粉煤灰=0.7∶0.1∶0.1∶0.1,RPC坍落度370 mm,扩展度615 mm,28 d抗压强度128.47 MPa,抗硫酸盐侵蚀等级KS90。