Downlink/Uplink Identification of Time-Division Duplexing-OFDMA Systems for Cognitive Radios

When coexisting with dual-link primary systems,secondary systems in cognitive radios should first distinguish between the primary downlinks and uplinks in order to efficiently explore their respective spectrum opportunities.Because of the assumptive prior knowledge about the time-frequency locations of primary downlinks and uplinks,this procedure is usually not considered in the design of cognitive radios.In this paper,a cooperative method is proposed for the downlink/uplink identification of time-division duplex-based orthogonal frequency-division multiple access systems.In this method,the power level of the primary link is extracted as the key feature,which also contributes to the subsequent cognitive behaviours.The effects of the primary and secondary systems and the effects of the detection parameters on the identification accuracy are all analysed in detail.The simulation results show that the proposed method can identify the primary links precisely and quickly with low complexity.

Simple Closed-Loop Method to Compensate Interference Asymmetry in Time-Division Duplex MIMO-OFDM Systems

In wireless communications systems with time-division duplex (TDD) deployment, channel reciprocity and symmetric interference between transmitter and receiver sides are two widely-adopted assumptions for the design of optimal adaptation transmission mode. However, in practice, there is an undesirable but non-negligible effect, namely the asymmetric interference, that makes the assumptions no longer valid. In this paper, a simple closed-loop feedback method of compensating interference asymmetry in TDD multiple-input multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) system is proposed. The system makes the estimated interference at transmit-side be able to track the instantaneous receive-side interference dynamically. The proposed method maintains constant frame error rate (FER) by adopting adaptive modulation coding (AMC) and power loading. The final simulations have verified the effectiveness of the new method.

Stability of networked control systems with multi-step delay based on time-division algorithm

A new control mode is proposed for a networked control system whose network-induced delay is longer than a sampling period. A time-division algorithm is presented to implement the control and for the mathematical modeling of such networked control system. The infinite horizon controller is designed, which renders the networked control system mean square exponentially stable.Simulation results show the validity of the proposed theory.

On Fault Diagnosis of Rotating Machinery Using Wavelet Time-division Scale Level Moment

Based on an in-depth study of wavelet gray moment, we proposed a concept of a time-division scale level moment and gave the specific definition; ulteriorly, we discussed the factors which affected the fault diagnosis ability of a time-division scale level moment. The analysis results in the caculation of six typical fault signals show that the time-division scale level moment can be used to display the detailed information of a wavelet gray level image, extract the signal＇s characteristics effectively, and distinguish the vibration fault. Compared to the method of a wave gray moment vector, the method mentioned in this paper can provide higher calculation speed and higher capacity of fault identification, so it is more suitable for online fault diagnosis for rotating machinery.

Electromagnetic responses on microstructures of duplex stainless steels based on 3D cellular and electromagnetic sensor finite element models

Microstructures determine mechanical properties of steels,but in actual steel product process it is difficult to accurately control the microstructure to meet the requirements.General microstructure characterization methods are time consuming and results are not rep-resentative for overall quality level as only a fraction of steel sample was selected to be examined.In this paper,a macro and micro coupled 3D model was developed for nondestructively characterization of steel microstructures.For electromagnetic signals analysis,the relative permeability value computed by the micro cellular model can be used in the macro electromagnetic sensor model.The effects of different microstructure components on the relative permeability of duplex stainless steel(grain size,phase fraction,and phase distribu-tion)were discussed.The output inductance of an electromagnetic sensor was determined by relative permeability values and can be val-idated experimentally.The findings indicate that the inductance value of an electromagnetic sensor at low frequency can distinguish dif-ferent microstructures.This method can be applied to real-time on-line characterize steel microstructures in process of steel rolling.

Progress in weldability research of duplex stainless steels

Duplex stainless steels(DSSs)show better corrosion resistance with higher strength than traditional austenite stainless steels in many aggressive environments,and can be welded properly with almost every welding processes,if proper heat input is provided.Progresses of research works on weldability of DSSs in recent years are reviewed in this paper.Balance control of ferrite/austenite phases is most important for DSSs welding.The phases balance can be controlled with filler materials,nitrogen addition in shielding gas,heat input,post weld heat treatment,and alternating magnetic field.Too high cooling rate results in not only extra ferrite,but also chromium nitride precipitation.While too low cooling rate or heating repeatedly results in precipitation of secondary austenite and intermetallic compounds.In both situations,mechanical properties and corrosion resistance of the DSS joints deteriorate.Recommended upper and lower limits of heat input and maximum interpass temperature should be observed.

Duplex PCR快速检测松材线虫

利用duplexPCR技术对松材线虫 (Bursaphelenchusxylophilus)与拟松材线虫 (B .mu cronatus)的rDNA部分核苷酸序列扩增。根据松材线虫与拟松材线虫的ITS1序列区别 ,设计出特异性引物 ,检测松材线虫的存在 ;在 5 8S ,2 8S保守序列区设计通用引物 。

Characteristics of microstructure and performance of laser-treated electroless Ni-P/Ni-W-P duplex coatings

Characteristics of microstructures of electroless Ni-P/Ni-W-P duplex coatings were investigated using SEM/EDX and XRD analysis techniques. Microhardness and wear behaviour of the coatings before and after laser crystallization were evaluated by measurements of hardnesses of coating surface and cross-section, and by unlubricated friction and wear experiments. The results indicate that it is possible to prepare electroless Ni-P/Ni-W-P duplex coatings by sequential immersion in two different plating baths. After laser crystallization, the microstructures of electroless Ni-P/Ni-W-P duplex coatings present the characteristics of higher degree of crystallization and larger grain size for outer layer Ni-W-P than inner Ni-P, but outer layer has a higher hardness. The wear resistance of laser-treated duplex coatings in a given process parameter conditions is superior to the as-plated ones. Laser treatment was performed directly in air without argon protection, which provides the possibility for application of industrialized production.

老年脑缺血患者颅外段颈动脉的Duplex、MRA、DSA检查结果分析（附105例报告）

本文报告１０５例老年脑缺血患者作颅外段颈动脉彩色超声（Ｄｕｐｌｅｘ）或／和磁共振造影（ＭＲＡ）、数控减影血管造影（ＤＳＡ）、手术探查的检查结果。甲组短暂性脑缺血（ＴＩＡ）患者７７例，经上述检查发现颈动脉存在不同程度的斑块性狭窄有４４例（５１．１％），乙组脑梗塞恢复后患者２８例，颈动脉存在不同程度狭窄有１４例（５０．０％）。全组１０５例检出颈动脉有斑块性狭窄５８例（５５．２％）。作者在讨论中指出对脑缺血患者的颈动脉病变的筛选检查方法首选为彩色超声扫描。作者认为确诊颈动脉存在７０％以上狭窄者，颈动脉内膜剥脱术是最好的治疗方法。

Identification of Orientia tsutsugamushi,spotted fever group and typhus group Rickettsia by duplex and nested PCR methods

Objective:To identify members of genera of rickettsia and O.tsutsugammhi simultaneously.Methods:Rapid and duplex and nested PCR methods have been established by designing primers based on the conserved regions of heat shock protein GroEL gene.345 mouse viscera samples including liver,spleen and kidney,96 Xenopsylla cheopis and 32 chiggers collected from Hongta areas of Yuxi city,Yunnan province were tested by the new PCR methods.Results:The result of the study showed that the new PCR methods could identify most members of genera -Rickettsia and Orientia simultaneously with 100%specificity and its sensitivity could test one copy per microliter.The results of detection prevalence of rickettsioses in mouse,flea and mites DNA samples showed that the total rickettsia infection rate in mouse was 34.78%(120/345).The total infection rates in R.typhi,O.t Karp and R.sibirica of mouse samples were 28.12%(97/345),19.71%(68/345) and O. 29%(1/345) respectively.Co-infection rates in R.typhi and 0.t Karp of mouse samples were 13.33%(46/ 345).O.t Karp type has been the main epidemic strain in these areas.Conclusion:We concluded that this PCR method could be used to detect multi-genera rickettsia simultaneously.Molecular evidences provided in this and previous studies strongly support that Hongta areas of Yuxi city are a natural focus for typhus and scrub typhus with the common occurrence of their confection.

Effect of Temperature and Cl^- Concentration on Pitting of 2205 Duplex Stainless Steel

The electrochemical behaviors of 2205 duplex stainless steel in NaCl solution with different temperatures and concentrations were studied by gravimetric tests, potentiodynamic polarization, electrochemical impedance spectroscopy and scanning electron microscopy. The experinental results show that temperature and chloride concentration have a great influence on the pitting resistance of 2205 duplex stainless steels. They not only effect the corrosion rate of pitting, but also change the shape of the pits. When NaCl solution was in low concentration and temperature below the critical pitting temperature, pits were very small and scattered with hemisphere-like shape. On the contrary, the pits of 2205 duplex stainless steel were large and sometimes had a lacy cover when the NaCl concentration was higher and the temperature was 70℃.

Hot deformation behavior of microstructural constituents in a duplex stainless steel during high-temperature straining

The hot deformation characteristics of 1.4462 duplex stainless steel （DSS） were analyzed by considering strain partitioning between austenite and ferrite constituents. The individual behavior of ferrite and austenite in microstructure was studied in an iso-stress condition. Hot compression tests were performed at temperatures of 800-1100~C and strain rates of 0.001-1 s-1. The flow stress was modeled by a hyperbolic sine constitutive equation, the corresponding constants and apparent activation energies were determined for the studied alloys. The constitutive equation and law of mixture were used to measure the contribution factor of each phase at any given strain. It is found that the contribution factor of ferrite exponentially declines as the Zener-HoUomon parameter （Z） increases. On the contrary, the austenite contribution polynomially increases with the increase of Z. At low Z values below 2.6. x 1015 （lnZ---35.5）, a negative contribution factor is determined for austenite that is attributed to dynamic recrystallization. At high Z values, the contribution factor of austenite is about two orders of magnitude greater than that of ferrite, and therefore, austenite can accommodate more strain. Microstructural characterization via electron back-scattered diffraction （EBSD） confirms the mechanical results and shows that austenite recrystallization is possible only at high temperature and low strain rate.

A duplex PCR for the rapid and simultaneous detection of Brucella spp.in human blood samples

Objective:To design a duplex PCR for rapid and simultaneous detection of Brucella species, in human blood samples.Methods:Fifty-two peripheral bloods samples were collected from suspicious patients with brucellosis.Following DNA extraction,PCR assay were performed, using three primers that could simultaneously identify and differentiate three major species of pathogenic Brucella in humans and animals.Results:Of the 52 peripheral bloods samples tested, 25 sample(48%) showed positive reactions in PCR.Twelve samples were positive for Brucella abortus(B.abortus)(23%,13 for Brucella melUensis(B.melUensis)(25%) and 0 for Brucella ovis (6.ovis)(Ow.Conclusions:This work de=monstrates dial in case where specific primers were utilized,duplex PCR has proved to be a simple,fast,and relatively inexpensive method for simultaneous detection of important species of Brucella in clinical samples.

The Full-Duplex Artificial Noise Scheme for Security of a Cellular System

This paper focuses on the problem of secure transmission in a cellular system. A full-duplex base station using artificial noise is adopted to improve both the uplink and downlink secrecy rate via pairing terminals which reverses the downlink and uplink of each other. We give the designs of artificial noise and the user's desired signal, and derive the pairing prin-ciple between terminals. Moreover, the influence of self-interference cancellation on secrecy rate is ex-plored. Simulation results show that the secrecy rate can get much better performance by adopting full-duplex artificial noise scheme and proposed pair-ing method. The downlink secrecy rate decreases with the distance between terminals. Besides the uplink secrecy rate is sensitive to the ability of self-interference cancellation.

Hot Deformation Behavior of an As-cast Duplex Stainless Steel

The hot deformation behavior of an as-cast OCrl7Mnl4Mo2N duplex stainless steel has been studied by hot compression test at the temperature range from 1000℃ to 1200℃, and the strain rates are 0.1 s-1, 1 s-1 and 5 s-1, respectively. It was found that during hot deformation there is only dynamic recovery taking place within the δ-ferrite phase, but the γ-austenite phase undergoes dynamic recrystallization. The activation energy of the steel for hot compression is estimated to be 480 kJ/mol.

Optimization of process parameters of the activated tungsten inert gas welding for aspect ratio of UNS S32205 duplex stainless steel welds

The activated TIG(ATIG) welding process mainly focuses on increasing the depth of penetration and the reduction in the width of weld bead has not been paid much attention.The shape of a weld in terms of its width-to-depth ratio known as aspect ratio has a marked influence on its solidification cracking tendency.The major influencing ATIG welding parameters,such as electrode gap,travel speed,current and voltage,that aid in controlling the aspect ratio of DSS joints,must be optimized to obtain desirable aspect ratio for DSS joints.Hence in this study,the above parameters of ATIG welding for aspect ratio of ASTM/UNS S32205 DSS welds are optimized by using Taguchi orthogonal array(OA)experimental design and other statistical tools such as Analysis of Variance(ANOVA) and Pooled ANOVA techniques.The optimum process parameters are found to be 1 mm electrode gap,130 mm/min travel speed,140 A current and 12 V voltage.The aspect ratio and the ferrite content for the DSS joints fabricated using the optimized ATIG parameters are found to be well within the acceptable range and there is no macroscopically evident solidification cracking.

Endometriosis of the duplex appendix: A case report and review of the literature

BACKGROUND Duplication of the appendix is an infrequent congenital malformation with a complex classification.The horseshoe appendix is a subtype of the duplex appendix and is rarely reported in the literature.Endometriosis is a common gynecological disease that rarely occurs in the appendix.Moreover,horseshoe appendix combined with endometriosis has not been previously reported.CASE SUMMARY Here,we describe a 44-year-old woman who was admitted with a 1-d history of migratory lower right quadrant pain.Physical examination was consistent with the signs of acute appendicitis.The patient underwent an emergency exploratory laparotomy.The distal tip of the appendix was in contact with the cecum by another base,or“horseshoe appendix”.In addition,a small intestinal mass and an ovarian mass were identified.Subsequently,appendectomy,partial resection of the small intestine,and right oophorectomy were successively performed.The histopathology confirmed the diagnosis of acute inflammation of the duplex appendix with endometriosis,small intestine endometriosis,and ovarian endometriosis.CONCLUSION Surgeons need to be aware of the possibility of the duplex appendix when performing an appendectomy,and this study emphasizes the importance of exploring the entire abdomen.

Welding of 2205 duplex stainless steel natural gas pipeline

There are abundant natural gas resources in western China, but many oil and gas fields are rich in chloridion, sulfureted hydrogen, carbon dioxide and other corrosive medium, which have strong corrosivity to pipeline. One gas field possesses abundant natural gas with great pressure, and the chloridion concentration in the water separated from gas is about 10% , so the medium has great corrosivity. In order to ensure the safety of the pipeline, about 13 km length pipeline and the internal pipes of a gas treatment plant that purifies gas about 12 billion cubic meter a year are made of 2205 duplex stainless steel （2205 DSS ） . 2205 DSS has many characteristics in welding with complex welding process; and because of high quality requirements for the construction of natural gas pipeline and restriction of on-site conditions, the site welding is very difficult. Around the engineering application, a large number of experimental researches have been carried out on the material microstructure, properties and weldability. Finally welded joints which conform to the requirements of standard are obtained, contributing to the first large-scale application of this material in the field of oil and gas pipelines. Considering the engineering application and the latest research development, the welding and key factors affecting the joint properties of 2205 DSS pipes are summarized and analyzed.

Influence of hot rolling on the microstructure of lean duplex stainless steel 2101

In this work, the microstructure and the strain partitioning of lean duplex stainless steel 2101 (LDX 2101) during different hot-rolling processes are investigated by optical microscopy and electron-backscattered diffraction (EBSD). The results show that the LDX 2101 exhibits poor thermoplasticity at high temperature. The four-pass hot-rolled plates show fewer edge-cracking defects and superior thermoplasticity compared with the two-pass hot-rolled plates prepared at different temperature. The phase boundary is the weakest site in the LDX 2101. The cracks are initiated and propagated along the phase boundaries during the hot-rolling process. According to the EBSD analysis, the increase of the hot-rolling pass can dramatically improve the strain distribution in ferrite and austenite phases and promote the strain transmission in the constituent phases, thereby improving the coordinated deformation ability of the two phases. This effect further in- creases the thermoplasticity and reduces the formation of edge cracks in LDX 2101.