On the effect of pitch and yaw angles in oblique impacts of smallcaliber projectiles

A terminal ballistic analysis of the effects of 7.62 mm × 51 AP P80 rounds on inclined high-strength armor steel plates is the focus of the presented study.The findings of an instrumented ballistic testing combined with 3D advanced numerical simulations performed using the IMPETUS Afea? software yielded the conclusions.The experimental verification proved that slight differences in the pitch-andyaw angles of a projectile upon an impact caused different damage types to the projectile’s core.The residual velocities predicted numerically were close to the experimental values and the calculated core deviations were in satisfactory agreement with the experimental results.An extended matrix of the core deviation angles with combinations of pitch-and-yaw upon impact angles was subsequently built on the basis of the numerical study.The presented experimental and numerical investigation examined thoroughly the influence of the initial pitch and yaw angles on the after-perforation projectile’s performance.

Impact of Blade-Flapping Vibration on Aerodynamic Characteristics of Wind Turbines under Yaw Conditions

Although the aerodynamic loading of wind turbine blades under various conditions has been widely studied,the radial distribution of load along the blade under various yaw conditions and with blade flapping phenomena is poorly understood.This study aims to investigate the effects of second-order flapwise vibration on the mean and fluctuation characteristics of the torque and axial thrust of wind turbines under yaw conditions using computational fluid dynamics(CFD).In the CFD model,the blades are segmented radially to comprehensively analyze the distribution patterns of torque,axial load,and tangential load.The following results are obtained.(i)After applying flapwise vibration,the torque and axial thrust of wind turbines decrease in relation to those of the rigid model,with significantly increased fluctuations.(ii)Flapwise vibration causes the blades to reciprocate along the axial direction,altering the local angle of attack and velocity of the blades relative to the incoming wind flow.This results in the contraction of the torque region from a circular shape to a complex“gear”shape,which is accompanied by evident oscillations.(iii)Compared to the tangential load,the axial load on the blades is more sensitive to flapwise vibration although both exhibit significantly enhanced fluctuations.This study not only reveals the impact of flapwise vibration on wind turbine blade performance,including the reduction of torque and axial thrust and increased operational fluctuations,but also clarifies the radial distribution patterns of blade aerodynamic characteristics,which is of great significance for optimizing wind turbine blade design and reducing fatigue risks.

Road Friction Estimation under Complicated Maneuver Conditions for Active Yaw Control

Road friction coefficient is a key factor for the stability control of the vehicle dynamics in the critical conditions. Obviously the vehicle dynamics stability control systems, including the anti-lock brake system（ABS）, the traction control system（TCS）, and the active yaw control（AYC） system, need the accurate tire and road friction information. However, the simplified method based on the linear tire and vehicle model could not obtain the accurate road friction coefficient for the complicated maneuver of the vehicle. Because the active braking control mode of AYC is different from that of ABS, the road friction coefficient cannot be estimated only with the dynamics states of the tire. With the related dynamics states measured by the sensors of AYC, a comprehensive strategy of the road friction estimation for the active yaw control is brought forward with the sensor fusion technique. Firstly, the variations of the dynamics characteristics of vehicle and tire, and the stability control mode in the steering process are considered, and then the proper road friction estimation methods are brought forward according to the vehicle maneuver process. In the steering maneuver without braking, the comprehensive road friction from the four wheels may be estimated based on the multi-sensor signal fusion method. The estimated values of the road friction reflect the road friction characteristic. When the active brake involved, the road friction coefficient of the braked wheel may be estimated based on the brake pressure and tire forces, the estimated values reflect the road friction between the braked wheel and the road. So the optimal control of the wheel slip rate may be obtained according to the road friction coefficient. The methods proposed in the paper are integrated into the real time controller of AYC, which is matched onto the test vehicle. The ground tests validate the accuracy of the proposed method under the complicated maneuver conditions.

An Adaptive Nonsingular Fast Terminal Sliding Mode Control for Yaw Stability Control of Bus Based on STI Tire Model

Due to the bus characteristics of large quality,high center of gravity and narrow wheelbase,the research of its yaw stability control(YSC)system has become the focus in the field of vehicle system dynamics.However,the tire nonlinear mechanical properties and the effectiveness of the YSC control system are not considered carefully in the current research.In this paper,a novel adaptive nonsingular fast terminal sliding mode(ANFTSM)control scheme for YSC is proposed to improve the bus curve driving stability and safety on slippery roads.Firstly,the STI(Systems Technologies Inc.)tire model,which can effectively reflect the nonlinear coupling relationship between the tire longitudinal force and lateral force,is established based on experimental data and firstly adopted in the bus YSC system design.On this basis,a more accurate bus lateral dynamics model is built and a novel YSC strategy based on ANFTSM,which has the merits of fast transient response,finite time convergence and high robustness against uncertainties and external disturbances,is designed.Thirdly,to solve the optimal allocation problem of the tire forces,whose objective is to achieve the desired direct yaw moment through the effective distribution of the brake force of each tire,the robust least-squares allocation method is adopted.To verify the feasibility,effectiveness and practicality of the proposed bus YSC approach,the TruckSim-Simulink co-simulation results are finally provided.The co-simulation results show that the lateral stability of bus under special driving conditions has been significantly improved.This research proposes a more effective design method for bus YSC system based on a more accurate tire model.

CFD Based Determination of Dynamic Stability Derivatives in Yaw for a Bird

Dynamic yaw stability derivatives of a gull bird are determined using Computational Fluid Dynamics（CFD） method. Two kinds of motions are applied for calculating the dynamic yaw stability derivatives CNr and CNβ. The first one relates to a lateral translation and, separately, to a yaw rotation. The second one consists of a combined translational and rotational motion. To determine dynamic yaw stability derivatives, the simulation of an unsteady flow with a bird model showing a harmonic motion is performed. The flow solution for each time step is obtained by solving unsteady Euler equations based on a finite volume approach for a small reduced frequency. Then, an evaluation of unsteady forces and moments for one cycle is conducted using harmonic Fourier analysis. The results of the dynamic yaw stability derivatives for both simulations of the model show a good agreement.

Direct Yaw Moment Control for Distributed Drive Electric Vehicle Handling Performance Improvement

For a distributed drive electric vehicle（DDEV） driven by four in-wheel motors, advanced vehicle dynamic control methods can be realized easily because motors can be controlled independently, quickly and precisely. And direct yaw-moment control（DYC） has been widely studied and applied to vehicle stability control. Good vehicle handling performance： quick yaw rate transient response, small overshoot, high steady yaw rate gain, etc, is required by drivers under normal conditions, which is less concerned, however. Based on the hierarchical control methodology, a novel control system using direct yaw moment control for improving handling performance of a distributed drive electric vehicle especially under normal driving conditions has been proposed. The upper-loop control system consists of two parts： a state feedback controller, which aims to realize the ideal transient response of yaw rate, with a vehicle sideslip angle observer; and a steering wheel angle feedforward controller designed to achieve a desired yaw rate steady gain. Under the restriction of the effect of poles and zeros in the closed-loop transfer function on the system response and the capacity of in-wheel motors, the integrated time and absolute error（ITAE） function is utilized as the cost function in the optimal control to calculate the ideal eigen frequency and damper coefficient of the system and obtain optimal feedback matrix and feedforward matrix. Simulations and experiments with a DDEV under multiple maneuvers are carried out and show the effectiveness of the proposed method： yaw rate rising time is reduced, steady yaw rate gain is increased, vehicle steering characteristic is close to neutral steer and drivers burdens are also reduced. The control system improves vehicle handling performance under normal conditions in both transient and steady response. State feedback control instead of model following control is introduced in the control system so that the sense of control intervention to drivers is relieved.

Feasibility of replacing the 3-coach with a 1.5-coach grouping trainmodel in wind tunnel experiment at different yaw angles

The effects of different yaw angles on the aerodynamic performance of city electric multiple units(EMUs)were investigated in a wind tunnel using a 1:16.8 scaled model.Pressure scanning valve and six-component box-type aerodynamic balance were used to test the pressure distribution and aerodynamic force of the head car respectively from the 1.5-and 3-coach grouping city EMU models.Meanwhile,the effects of the yaw angles on the pressure distribution of the streamlined head as well as the aerodynamic forces of the train were analyzed.The experimental results showed that the pressure coefficient was the smallest at the maximum slope of the main shape-line.The side force coefficient and pressure coefficient along the head car cross-section were most affected by crosswind when the yaw angle was 55°,and replacing a 3-coach grouping with a 1.5-coach grouping had obvious advantages for wind tunnel testing when the yaw angle was within 24.2°.In addition,the relative errors of lift coefficient C_(L),roll moment coefficient C_(Mx),side force coefficient C_(S),and drag coefficient C_(D) between the 1.5-and 3-coach cases were below 5.95%,which all met the requirements of the experimental accuracy.

Integrated yaw and rollover control based on differential braking for off-road vehicles with mechanical elastic wheel

Aiming at the issue of yaw and rollover stability control for off-road vehicles with non-pneumatic mechanical elastic wheel(MEW),an integrated control system based on fuzzy differential braking is developed.By simplifying the structure of the MEW,a corresponding fitting brush tire model is constructed and its longitudinal and lateral tire force expressions are set up,respectively.Then,a nonlinear vehicle simulation model with MEW is established to validate the proposed control scheme based on Carsim.The designed yaw and rollover control system is a two-level structure with the upper additional moment controller,which utilizes a predictive load transfer ratio(PLTR)as the rollover index.In order to design the upper integrated control algorithm,fuzzy proportional-integral-derivative(PID)is adopted to coordinate the yaw and rollover control,simultaneously.And the lower control allocator realizes the additional moment to the vehicle by differential braking.Finally,a Carsim-simulink co-simulation model is constructed,and simulation results show that the integrated control system could improve the vehicle yaw and roll stability,and prevent rollover happening.

Debris cloud structure and hazardous fragments distribution under hypervelocity yaw impact

This study investigates how the debris cloud structure and hazardous fragment distribution vary with attack angle by simulating a circular cylinder projectile hypervelocity impinging on a thin plate using the finite element-smoothed particle hydrodynamics(FE-SPH)adaptive method.Based on the comparison and analysis of the experimental and simulation results,the FE-SPH adaptive method was applied to address the hypervelocity yaw impact problem,and the variation law of the debris cloud structure with the attack angle was obtained.The screening criterion of the hazardous fragment at yaw impact is given by analyzing the debris formation obtained by the FE-SPH adaptive method,and the distribution characteristics of hazardous fragments and their relationship with the attack angle are given.Moreover,the velocity space was used to evaluate the distribution range and damage capability of asymmetric hazardous fragments.The maximum velocity angle was extended from fully symmetrical working conditions to asymmetrical cases to describe the asymmetrical debris cloud distribution range.In this range,the energy density was calculated to quantitatively analyze how much damage hazardous fragments inflict on the rear plate.The results showed that the number of hazardous fragments generated by the case near the 35°attack angle was the largest,the distribution range was the smallest,and the energy density was the largest.These results suggest that in this case,debris cloud generated by the impact had the strongest damage to the rear plate.

Numerical Analysis of Horizontal-Axis Wind Turbine Characteristics in Yawed Conditions

Computational fluid dynamics (CFD) modeling and experiments have both advantages and disadvantages. Doing both can be complementary, and we can expect more effective understanding of the phenomenon. It is useful to utilize CFD as an efficient tool for the turbomachinery and can complement uncertain experimental results. However the CFD simulation takes a long time for a design in generally. It is need to reduce the calculation time for many design condi- tions. In this paper, it is attempted to obtain the more accurate characteristics of a wind turbine in yawed flow condi- tions for a short time, using a few grid points. It is discussed for the reliability of the experimental results and the CFD results.

Validation of the Actuator Line Model for Simulating Flows past Yawed Wind Turbine Rotors

The Actuator Line/Navier-Stokes model is validated against wind tunnel measurements for flows past the yawed MEXICO rotor and past the yawed NREL Phase VI rotor. The MEXICO rotor is operated at a rotational speed of 424 rpm, a pitch angle of ?2.3。, wind speeds of 10, 15, 24 m/s and yaw angles of 15。, 30。 and 45。. The computed loads as well as the velocity field behind the yawed MEXICO rotor are compared to the detailed pressure and PIV measurements which were carried out in the EU funded MEXICO project. For the NREL Phase VI rotor, computations were carried out at a rotational speed of 90.2 rpm, a pitch angle of 3。, a wind speed of 5 m/s and yaw angles of 10。and 30。. The computed loads are compared to the loads measured from pressure measurement.

Research on Direct Yaw Moment Control Strategy of Distributed-Drive Electric Vehicle Based on Joint Observer

Combined with the characteristics of the distributed-drive electric vehicle and direct yaw moment control,a double-layer structure direct yaw moment controller is designed.The upper additional yaw moment controller is constructed based on model predictive control.Aiming at minimizing the utilization rate of tire adhesion and constrained by the working characteristics of motor system and brake system,a quadratic programming active set was designed to optimize the distribution of additional yaw moments.The road surface adhesion coefficient has a great impact on the reliability of direct yaw moment control,for which joint observer of vehicle state parameters and road surface parameters is designed by using unscented Kalman filter algorithm,which correlates vehicle state observer and road surface parameter observer to form closed-loop feedback correction.The results show that compared to the“feedforward+feedback”control,the vehicle’s error of yaw rate and sideslip angle by the model predictive control is smaller,which can improve the vehicle stability effectively.In addition,according to the results of the docking road simulation test,the joint observer of vehicle state and road surface parameters can improve the adaptability of the vehicle stability controller to the road conditions with variable adhesion coefficients.

Reference Modelof Desired Yaw Anglefor Automated Lane Changing Behavior of Vehicle

In this paper,it studies the problem of trajectory planning and tracking for lane changing behavior of vehicle in automatic highway systems. Based on the model of yaw angle acceleration with positive and negative trapezoid constraint,by analyzing the variation laws of yaw motion of vehicle during a lane changing maneuver,the reference model of desired yaw angle and yaw rate for lane changing is generated. According to the yaw angle model,the vertical and horizontal coordinates of trajectory for vehicle lane change are calculated. Assuming that the road curvature is a constant,the difference and associations between two scenarios are analyzed,the lane changing maneuvers occurred on curve road and straight road,respectively. On this basis,it deduces the calculation method of desired yaw angle for lane changing on circular road. Simulation result shows that,it is different from traditional lateral acceleration planning method with the trapezoid constraint,by applying the trapezoidal yaw acceleration reference model proposed in this paper, the resulting expected yaw angular acceleration is continuous,and the step tracking for steering angle is not needed to implement. Due to the desired yaw model is direct designed based on the variation laws of raw movement of vehicle during a lane changing maneuver, rather than indirectly calculated from the trajectory model for lane changing, the calculation steps are simplified.

Influence of Wind Speed, Stay Cable Inclination Angle and Wind Yaw Angle on Formation of Rivulets

Combining lubrication theory and CFD technology, a finite element model is established to simulate the rain-wind-induced vibration(RWIV). Based on Spalart-Allmaras(S-A)turbulence type, COMSOL software is adopted to calculate the wind pressure coefficient and wind friction coefficient that vary with the location and time. To verify the veracity and rationality of this method, the formation and evolution of rivulets at different wind speeds are studied and compared with the existing experimental results. Furthermore, the time, location, height and width of the initial formation of rivulets are analyzed at different wind speeds, cable inclination angles and wind yaw angles. The results show that the three influencing factors mentioned above have great effect on the formation of rivulet, and the influencing tendency, range and degree are different from each other.

Validation of Chaviaro Poulos and Hansen Stall Delay Model in the Case of Horizontal Axis Wind Turbine Operating in Yaw Conditions

Operating in natural wind field, the horizontal axis wind turbines are subject to cyclical variation of aerodynamic loads. This cyclical loads fluctuation is a result of two aerodynamic phenomenon: the first one is the advancing and retreating blade effect;the second one is related to the cyclical variation of induced velocity at the rotor plane. In these operating conditions, the correct prediction of this load variation is necessary to predict some important parameters linked to the fatigue and stability of free yawing turbines. The main objective of the present study is the evaluation of the azimuthal variation of normal force at different radial positions. To model the problem, the blade element momentum theory is used and wind turbine is supposed operate in yaw conditions. The aerodynamic coefficients are corrected using Chaviaropoulos and Hansen model to take into account the phenomenon of stall delay. A computer code was developed to obtain the numerical values and results are compared with measurements performed in the NASA Ames wind tunnel.

A Genetic Algorithm for Optimizing Yaw Operation Control in Wind Power Plants

A genetic algorithm is proposed to optimize the yaw control system used for the stable and efficient operation of turbines in wind power plants.In particular,the factors that produce yaw static deviation are analyzed.Then,the sought optimization method for the yaw static deviation of the wind turbine is implemented by using a lidar wind meter in the engine room in order to solve the low accuracy problem caused by yaw static deviation.It is shown that fuzzy control can overcome problematic factors such as the randomness of wind direction and track the change of wind direction accurately.Power control implementation is simple,as only the voltage and current of the generator need to be measured.

A data-driven machine learning approach for yaw control applications of wind farms

This study proposes a cost-effective machine-learning based model for predicting velocity and turbulence kineticenergy fields in the wake of wind turbines for yaw control applications.The model consists of an auto-encoderconvolutional neural network(ACNN)trained to extract the features of turbine wakes using instantaneous datafrom large-eddy simulation(LES).The proposed framework is demonstrated by applying it to the Sandia NationalLaboratory Scaled Wind Farm Technology facility consisting of three 225 kW turbines.LES of this site is performedfor different wind speeds and yaw angles to generate datasets for training and validating the proposed ACNN.It is shown that the ACNN accurately predicts turbine wake characteristics for cases with turbine yaw angleand wind speed that were not part of the training process.Specifically,the ACNN is shown to reproduce thewake redirection of the upstream turbine and the secondary wake steering of the downstream turbine accurately.Compared to the brute-force LES,the ACNN developed herein is shown to reduce the overall computational costrequired to obtain the steady state first and second-order statistics of the wind farm by about 85%.

A New Methodology for Reducing Yaw Rate Estimation Error

The dependency of the steady-state yaw rate model on vehicle weight and its distribution is studied in this paper. A speed-dependent adjustment of the yaw rate model is proposed to reduce the yaw rate estimation error. This new methodology allows the calibration engineer to minimize the yaw rate estimation error caused by the different weight conditions without going through the calibration process multiple times. It is expected that this modified yaw rate model will improve the performance of Electronic Stability Control (ESC) systems such as response time and robustness.

Analysis of Near-Wake Deflection Characteristics of Horizontal Axis Wind Turbine Tower under Yaw State

The yaw of the horizontal axis wind turbine results in the deflection of the wake flow field of the tower.The reasonable layout of wind farm can reduce the power loss of the downstream wind turbine generators due to the blocking effect of the upstream wake flow and increase the output power of the whole wind farm.However,there is still much space for further research.In this paper,experimental research is conducted on the near-wake deflection characteristics of wind turbine tower under yaw state,expecting the effect of throwing away a brick in order to get a gem.In the low-turbulence wind tunnel test,regarding the most unfavorable position where the rotating blades coincide with the tower,Particle image velocimetry(PIV)technology is used to test the instantaneous velocity field and output power and analyze experimental data at four different yaw angles,different inflow velocities and heights.Meanwhile,in order to quantitatively analyze the laws on wake deflection,the radon transformation is used to analyze the velocity contour for calculating the wake direction angle,and the results show high reliability.The comprehensive experimental results indicate that the near-wake flow field of the tower obviously deflects towards a side in the horizontal plane.With the increase of the yaw angle,the deflection angle of the wake flow field further increases,and the recovery of wake velocity accelerates.The closer to the blade root,the more complex the flow is,and the influence of the blade on the near wake of the tower is gradually weakened.The change laws on the wake direction angle with the yaw angle and the blade spanwise direction are obtained.The experiment in this paper can provide guidance for layout optimization of wind farm,and the obtained data can provide a scientific basis for the research on performance prediction of horizontal axis wind turbine.