基于“教、学、评”一体化的“硫酸”微课设计

文章首先阐述了微课的概念及特点,然后分析了基于“教、学、评”一体化的微课设计的作用,接着提出了基于“教、学、评”一体化的“硫酸”微课设计,最后对基于“教、学、评”一体化的“硫酸”微课设计进行了反思。

“加害者隐身”:网络热词的流播机制解析--以“硫酸男孩”为例

网络热词的“热”体现为巨大的流量效应,“流量为王”的数据热遮蔽了媒体事件报道背后的隐性问题:“加害者隐身”现象。本研究运用网络观察法,通过“硫酸男孩”的案例分析,解析网络热词流播的表征归因与传播机制。研究发现,媒体报道中情绪优先于事实、报道传统框架的固化和社交平台的算法机制共同促成了“加害者隐身”现象,网络热词流播的隐性机制体现在弱编码叙事、智能推送和参与式文化三个层面。

Resource utilization of hazardous gypsum sludge in oxidation smelting of lead concentrate

Gypsum sludge,a hazardous waste generated by the non-ferrous smelting industry,presents a significant challenge for disposal and utilization.To investigate the feasibility of substituting gypsum sludge for limestone as a flux for smelting,the effects of calcium sulfate(CaSO_(4))and smelting conditions on oxygen-rich smelting of lead concentrate were studied.The interaction between CaSO_(4)and sulfides facilitates the conversion of CaSO_(4)into CaO,which is crucial for slag formation.The order of the influence of sulfide minerals on the conversion of CaSO_(4)is pyrite>sphalerite>galena.When using gypsum sludge exclusively as the calcium source,under optimal conditions with a CaO/SiO_(2)mass ratio of 0.8,an FeO/SiO_(2)mass ratio of 1.2,a melting temperature of 1150℃,an oxygen flow rate of 1.3 L/min,the recovery rates of Pb and Zn in the lead-rich slag reached 85.01%and 95.69%,respectively,with a sulfur content of 2.65 wt%.The As content in the smelting slag obtained by reduction smelting was 0.02 wt%.Resource utilization of gypsum sludge in lead smelting is a feasible method.

Investigation of mortar corrosion by an acidophilic sulfur-oxidizing microorganism A.thiooxidans

The corrosion behavior of the acidophilic sulfur-oxidizing microorganism(ASOM)Acidithiobacillusthiooxidans(A.thiooxidans)on mortar was investigated for changes of medium and mortar,as well as for weight lossand surface morphology of mortar specimens.Weight loss analysis showed that mortar weight was reduced by(15.1±2.2)%after 56 d.Morphological surface analysis of mortar specimens showed weakly structured fibrous substances with2−100μm in size.The pH variations of the mortar surface and medium indicated that biogenic sulfuric acid had beenproduced by A.thiooxidans.The results prove that A.thiooxidans accelerated concrete corrosion and caused concretefailure.

Separation of halogens and recovery of heavy metals from secondary copper smelting dust

The separation of halogens and recovery of heavy metals from secondary copper smelting(SCS)dust using a sulfating roasting−water leaching process were investigated.The thermodynamic analysis results confirm the feasibility of the phase transformation to metal sulfates and to gaseous HF and HCl.Under the sulfating roasting conditions of the roasting temperature of 250℃ and the sulfuric acid excess coefficient of 1.8,over 74 wt.%of F and 98 wt.%of Cl were volatilized into flue gas.Approximately 98.6 wt.%of Zn and 96.5 wt.%of Cu in the roasting product were dissolved into the leaching solution after the water leaching process,while the leaching efficiencies of Pb and Sn were only 0.12%and 0.22%,respectively.The mechanism studies indicate the pivotal effect of roasting temperature on the sulphation reactions from various metal species to metal sulfates and the salting out reactions from various metal halides to gaseous hydrogen halides.

Research progress on the skincare efficacy of sulfated glycosaminoglycans

With the improvement of consumers’scientific skin care consciousness,skin problems-oriented efficacy skin care and precise skin care methods have become the future development trend.Glycosaminoglycans are long,linear polysaccharides comprised of repeated disaccharide units,which are highly expressed endogenously in the skin.They are commonly present in skin cells,cell surface and extracellular matrix,with pleiotropic biological function.In addition to hyaluronic acid,the sulfated glycosaminoglycans heparin,heparan sulfate,dermatan sulfate and chondroitin sulfate play an important role in anti-wrinkle,firming,soothing,and improving microvascular circulation,but are still in the research and development stage in cosmetics.This paper summarizes the skincare mechanism of sulfated glycosaminoglycans,and demonstrates the potential of sulfated glycosaminoglycans as functional raw materials in cosmetics.

Adsorption behaviors and mechanisms of gold recovery from thiosulfate solution by ion exchange resin

The adsorption behaviors and mechanisms of gold from thiosulfate solution on strong-base anion exchange resin were systematically investigated.The comparison experiment of adsorption ability and selectivity for gold showed that gel Amberlite IRA-400 resin with Type Ⅰ quaternary ammonium functional group had better adsorption performance.The increases of resin dosage,ammonia concentration and solution pH were favorable to gold adsorption,whereas the rises of cupric and thiosulfate concentrations were disadvantageous to gold loading.Microscopic characterization results indicated that gold was adsorbed in the form of [Au(S_(2)O_(3))_(2)]^(3–) complex anion by exchanging with the counter ion Cl^(–) in the functional group of the resin.Density functional theory calculation result manifested that gold adsorption was mainly depended on the hydrogen bond and van der Waals force generated between O atom in [Au(S_(2)O_(3))_(2)]^(3–) and H atom in the quaternary ammonium functional group of the resin.

Effect of organic carbon sources on the anodic corrosion of magnesium AZ31B by sulfate-reducing prokaryote

Corrosion caused by sulfate-reducing prokaryotes(SRP)is an important cause of magnesium alloy anode failure in oil pipeline.In this study,the effects of Desulfovibrio sp.HQM3 on the corrosion behavior of AZ31B magnesium alloy anode in organic carbon sources with different contents in simulated tidal flat environment were analyzed using weight loss test,surface analysis and electrochemical analysis technologies.The results showed that the weight loss rate of coupons in low carbon sources contents(0%,1%,10%)was higher than that in 100%carbon sources.Electrochemical analyses showed that the corrosion current density(J_(corr))under low carbon sources contents was larger,while the charge transfer resistance(R_(ct))was lower,leading to a higher corrosion rate compared to those under 100%carbon sources content.Observations from scanning electron microscopy(SEM)and confocal laser scanning microscopy(CLSM)revealed more severe pitting corrosion on the alloy surface in the absence of carbon sources.In addition,a large number of nanowires were observed between bacteria on the alloy surface using SEM.Combined with thermodynamic calculations,it was demonstrated that the corrosion of coupons by Desulfovibrio sp.HQM3 in the absence of carbon sources was achieved through extracellular electron transfer.

Corrosion behavior of B10 copper-nickel alloy beneath a deposit caused by sulfate-reducing bacteria with carbon source starvation in marine environments

Copper-nickel alloys can suffer severe localized corrosion in marine environments containing sulfate-reducing bacteria(SRB),but the effect of SRB on the under-deposit corrosion of copper-nickel alloys is unknown.In this work,the corrosion behavior of B10 copper-nickel alloy beneath a deposit caused by SRB with carbon source starvation in artificial seawater was studied based on electrochemical measurements and surface analysis.Results demonstrate that SRB with an organic carbon starvation can survive in artificial water but most SRB cells have died.The survived SRB cells can attach to the bare and deposit-covered B10 copper-nickel alloy,leading to the corrosion acceleration.Due to the limitation of organic carbon source,the pitting corrosion of B10 copper-nickel alloy caused by SRB is not serious.However,serious pitting corrosion of the deposit-covered B10 copper-nickel alloy can be found both in abiotic and biotic conditions,and the pitting corrosion and uniform corrosion are further accelerated by SRB.There is a galvanic effect between the bare and deposit-covered specimens in the presence of SRB in the early stage but the galvanic effect after 5 d of testing can be neglected due to the low OCP difference values.

Synthesis of High Purity Lithium Sulfide for Sulfide Solid Electrolyte Applications through Hydrogen Reduction of Lithium Sulfate

This paper is aimed to present a clean,inexpensive and sustainable method to synthesize high purity lithium sulfide(Li_(2)S)powder through hydrogen reduction of lithium sulfate(Li_(2)SO_(4)).A three-step reduction process has been successfully developed to synthesize well-crystallized and single-phase Li_(2)S powder by investigating the melting,sintering and reduction behavior of the mixtures of Li_(2)SO_(4)-Li_(2)S.High purity alumina was found to be the most suitable crucible material for producing high purity Li_(2)S,because it was not attacked by the Li_(2)SO_(4)-Li_(2)S melt during heating,as compared with other materials,such as carbon,mullite,quartz,boron nitride and stainless steel.The use of synthesized LizS resulted in higher purity and substantially higher room temperature ionic conductivity(2.77 mS·cm^(-1))for the argyrodite sulfide electrolyte Li_(6)PS_(5)Cl than commercial Li_(2)S(1.12 mS·cm^(-1)).This novel method offers a great opportunity to produce battery grade Li_(2)S for sulfide solid electrolyte applications.

Synthesis,crystal structures,and antibacterial activities of two zinc(Ⅱ) complexes bearing 5⁃phenyl⁃1H⁃pyrazole group

A novel compound(H_(2)L)SCN(5⁃methyl⁃3⁃phenyl⁃2H⁃pyrazol⁃1⁃ium thiocyanate)has been obtained by the reaction of thiosemicarbazide with benzoylacetone in ethanol.Two zinccomplexes[Zn(HL)_(2)(NCS)(CH_(3)COO)](1)and[Zn_(2)(L)_(2)(HL)_(2)(NCS)_(2)]_(2)·2CH_(3)OH(2)have been synthesized by the coordination reactions of Zn(OAc)_(2)·2H_(2)O or ZnCl_(2)with(H_(2)L)SCN under reflux conditions.Elemental analyses and single⁃crystal X⁃ray diffraction have con⁃firmed the structures of the synthesized compounds.The(H_(2)L)SCN ligand and complex 1 pertain to the triclinic sys⁃tem with space group P1,while complex 2 belongs to the monoclinic system with space group P2_(1)/n.Additionally,the antibacterial activities of the compounds were evaluated in vitro using the agar diffusion method against the bac⁃terial strains(Candida albicans,Staphylococcus aureus,and Escherichia coli).The results showed that the ligand exhibited relatively good antibacterial activities against the bacteria,and the complexes possessed stronger antibac⁃terial activities against the same bacteria than the free ligand.CCDC:2190252,(H2L)SCN;2190253,1;2190256,2.

Acid mine drainage activation mechanism on lime-depressed pyrite flotation from copper sulfide ore

The lime-depressed pyrite from Cu differential flotation tailings with acid mine drainage(AMD)as a natural activator was recovered.The effect of AMD on lime-depressed pyrite flotation was investigated by a series of laboratory flotation tests and surface analytical techniques.Flotation test results indicated that AMD could effectively activate the pyrite flotation with a sodium butyl xanthate(SBX)collector,and a high-quality sulfur concentrate was obtained.Pulp ion concentration analysis results indicated that AMD facilitated desorption of Ca^(2+)and adsorption of Cu^(2+)on the depressed-pyrite surface.Adsorption measurements and contact angle analysis results confirmed that adding AMD improved the adsorption amount of SBX collector on the pyrite surface and increased the contact angle by 31°.Results of Raman spectroscopy and X-ray photoelectron spectroscopy analysis indicated that AMD treatment promoted the formation of hydrophobic species(S^(0) hydrophobic entity and copper sulfides)and the removal of hydrophilic calcium and iron species on the pyrite surface,which reinforced the adsorption of collector.The findings of the present research provide important theoretical basis and technical support for a cleaner production of copper sulfide ores.

Efficient in-situ end-functionalization of polydienes by isothiocyanate via neodymium mediated coordinative chain transfer polymerization system

End-functionalization of polydiene rubbers can not only improve its compatibility with inorganic fillers,but also enhance the overall mechanical properties.Nevertheless,for traditional neodymium(Nd)diene polymerization systems,it is highly challenging to achieve such end-functionalizations,because most of polydienyl chains are capped withη3-allyl-Nd moiety during the end of polymerization,which shows very poor reactivity with nucleophile compounds.We launched a new diene polymerization strategy calling coordinative chain transfer polymerization(CCTP)[1].In such a system,all the polydienyl chains are capped withη1-allyl-Al moieties,which reveal greater reactivity with cyclic esters and epoxide compounds,providing an effective manner to prepare polydiene-polyester amphiphilic block copolymers.Inspired by such findings,we now show herein how such types of chain-ends react with isot-hiocyanate to demonstrate an efficient in-situ manner to access end-functionalized polydienes by using CCTP.

Flotation separation of chalcopyrite from galena by sodium humate and ammonium persulfate

The flotabilities of chalcopyrite and galena with sodium humate（HA） and ammonium persulfate（APS） as the depressant were studied by flotation test, adsorption measurement and infrared spectroscopic analysis. Single mineral flotation test shows that the slurry oxidation environment and the proper oxidation of galena surface are prerequisites for the depression of galena by sodium humate. The closed-circuit flotation test of copper/lead bulk concentrate shows that the grade and recovery of Cu reach 30.47% and 89.16% respectively and those of Pb reach 2.06% and1.58% respectively in copper concentrate, and the grade and recovery of Pb reach 50.34% and 98.42% and those of Cu reach 1.45% and 10.84% respectively in lead concentrate with HA and APS. The selective depression effect of HA and APS is more obvious than that of potassium dichromate. The results of FTIR analysis and adsorption measurements indicate that the adsorption of sodium humate on the fresh surface of galena is negligible, while after oxidation, sodium humate can be chemically adsorbed on the surface of galena. According to the theory of solubility product, the sodium humate can display the oxidation product PbSO_4, after then, adsorb on the surface of lead chemically to produce inhibitory effect. Thus, it can be seen that the combination of HA and APS is an efficient non-toxic reagent to achieve cleaning separation copper/lead bulk concentrate by flotation. The combination of HA and APS is an efficient non-toxic reagent to achieve cleaning for copper/lead bulk concentrate by flotation.

Leaching characteristics of ion-adsorption type rare earths ore with magnesium sulfate

Magnesium sulfate was proposed to be leaching agent to deal with the ion-adsorption type rare earths ore to reduce or even eliminate ammonia?nitrogen emissions. The effects of temperature, particle size and stirring speed on rare earth leaching process and the leaching behaviors of the single rare earth element were investigated in order to reveal the rare earth leaching characteristics. Besides, the comparison of leaching effects between magnesium sulfate and ammonium sulfate was also studied. The results showed that the rare earth leaching process could be well described with inner diffusion control model and the apparent activation energy was 9.48 kJ/mol. The leaching behaviors of the single rare earth element were brought into correspondence with rare earths. Moreover, when the concentration of leaching agent was 0.20 mol/L, the rare earth leaching efficiency could all reach above 95% and the leaching efficiency of aluminum impurities could be restrained by 10% using magnesium sulfate compared with ammonium sulfate.

Leaching kinetics of low-grade copper ore containing calcium-magnesium carbonate in ammonia-ammonium sulfate solution with persulfate

The leaching kinetics of copper from low-grade copper ore was investigated in ammonia-ammonium sulfate solution with sodium persulfate. The effect parameters of stirring speed, temperature, particle size, concentrations of ammonia, ammonium sulfate and sodium persulfate were determined. The results show that the leaching rate is nearly independent of agitation above 300 r/min and increases with the increase of temperature, concentrations of ammonia, ammonium sulfate and sodium persulfate. The EDS analysis and phase quantitative analysis of the residues indicate that bornite can be dissolved by persulfate oxidization. The leaching kinetics with activation energy of 22.91 kJ/mol was analyzed by using a new shrinking core model （SCM） in which both the interfacial transfer and diffusion across the product layer affect the leaching rate. A semi-empirical rate equation was obtained to describe the leaching process and the empirical reaction orders with respect to the concentrations of ammonia, ammonium sulfate and sodium persulfate are 0.5, 1.2 and 0.5, respectively.

Extraction of alumina from fly ash by ammonium hydrogen sulfate roasting technology

NH4HSO4 roasting technology was used for preparing Al2O3 from fly ash. First, Al and Fe were extracted from fly ash by NH4HSO4 roasting and deionized water leaching. Then, the Al and Fe in the leached liquid were precipitated by adding NH4HCO3 solution. After the mixed precipitations of Al（OH）3 and Fe（OH）3 were leached by NaOH solution, the NaAl（OH）4 solution was decomposed by carbonation. Finally, the pure Al（OH）3 was calcined to α-Al2O3. The optimal conditions of the whole technology were determined by experiments. The quality ofa-Al2O3 product is up to the technical indicator of YS/T 274-1998 standard.

Separation and recovery of Cu and As during purification of copper electrolyte

Cu, As, Sb and Bi in copper electrolyte could be efficiently removed by reducing with SO2 followed by evaporative crystallization. As2O3 and CuSO4·5H2O were obtained after crystallized product was treated by dissolution, oxidation, neutralization, sedimentation, filtration and evaporative crystallization. The removal rates of Cu, As, Sb and Bi are 87.1%, 83.9%, 21.0% and 84.7%, respectively, when As （Ⅴ） in copper electrolyte is fully reduced to As （Ⅲ） by SO2, and the H2SO4 in concentrated copper electrolyte is 645 g/L. The removal rate of As is 92.81% when 65 g crystallized product is dissolved in 200 mL water at 30 ℃. The CuSO4·5H2O content is 98.8% when the filtrate is purified under the conditions that n（Fe）：n（As） is 1.2, the dosage of H2O2 is 19 times the stoichiometric needed, temperature is 45 ℃, time is 40 min, pH is 3.7, and then is evaporation crystallized.