Nickel nanowire and nanotube arrays as supports for Pt-Pd catalyst were prepared by elec- troless deposition with anodic aluminum oxide template. Pt-Pd composite catalyst was de- posited on the arrays by displacement ...Nickel nanowire and nanotube arrays as supports for Pt-Pd catalyst were prepared by elec- troless deposition with anodic aluminum oxide template. Pt-Pd composite catalyst was de- posited on the arrays by displacement reaction. SEM images show that the nickel nanowires have an average diameter of I00 nm and the nickel nanotubes have an average inner diameter of 200 nm. EDS scanning reveals that elemental Pt and Pd disperse uniformly on the arrays. Cyclic voltammetry study indicates that the nickel nanotube array loaded with Pt-Pd pos- sesses a higher electrochemical activity for ethanol oxidation than the nickel nanowire array with Pt-Pd.展开更多
Experimental results on processing,structural and mechanical characterization of a multilayer composite based on commercially pure aluminum foils were presented.A multilayer composite was produced by hot-rolling of an...Experimental results on processing,structural and mechanical characterization of a multilayer composite based on commercially pure aluminum foils were presented.A multilayer composite was produced by hot-rolling of anodized and non-anodized aluminum foils alternately sandwiched.In addition,the same process was applied for bonding of non-anodized foils.In both cases,obtained multilayer composites were compact and sound.In order to study composites microstructural evolution and mechanical properties,optical and scanning electron microscopy(SEM),energy dispersive spectrometry(EDS),X-ray diffraction(XRD)analysis,hardness,tensile and three-point flexural tests were performed.Microstructural characterization confirmed that the rod-like particles distributed in parallel rows in the composite aluminum matrix with anodized foils correspond to Al2O3.Maximum and minimum peaks of oxygen and aluminum,respectively,suggest that after the final hot-rolling of composite with non-anodized foils,a small amount of coarser particles were formed at boundaries between foils.Hardness,strength,modulus of elasticity and flexural strength of both multilayer composites were much higher than those of pure aluminum,whereas ductility was significantly less.The composite with anodized foils exhibited the highest strength and modulus of elasticity,but lower ductility compared to composite processed from non-anodized foils.Fracture failure corresponded to the change of ductility.展开更多
The CaO doped 10NiO-NiFe2O4 composite ceramics were prepared by the cold isostatic pressing-sintering process, and the effects of CaO content on the phase composition, mechanical property and thermal shock resistance ...The CaO doped 10NiO-NiFe2O4 composite ceramics were prepared by the cold isostatic pressing-sintering process, and the effects of CaO content on the phase composition, mechanical property and thermal shock resistance of 10NiO-NiFe2O4 composite ceramics were studied. The results show that the samples mainly consist of NiO and NiFe2O4 when content of CaO is less than 4%(mass fraction), bending strength increases obviously by CaO doping. Bending strength of the samples doped with 2% CaO is above 185 MPa, but that of the samples without CaO is only 60 MPa. Fracture toughness is improved obviously by CaO doping, the samples doped with 2% CaO have the maximum fracture toughness of 2.12 MPa ·m1/2 , which is about two times of that of the undoped ceramics. CaO doping is bad to thermal shock resistance of 10NiO-NiFe2O4 composite ceramics.展开更多
文摘Nickel nanowire and nanotube arrays as supports for Pt-Pd catalyst were prepared by elec- troless deposition with anodic aluminum oxide template. Pt-Pd composite catalyst was de- posited on the arrays by displacement reaction. SEM images show that the nickel nanowires have an average diameter of I00 nm and the nickel nanotubes have an average inner diameter of 200 nm. EDS scanning reveals that elemental Pt and Pd disperse uniformly on the arrays. Cyclic voltammetry study indicates that the nickel nanotube array loaded with Pt-Pd pos- sesses a higher electrochemical activity for ethanol oxidation than the nickel nanowire array with Pt-Pd.
基金financially supported by the Ministry of Education,Science and Technological Development of the Republic of Serbia through the Project Nos.Ⅲ45012 and ON174004
文摘Experimental results on processing,structural and mechanical characterization of a multilayer composite based on commercially pure aluminum foils were presented.A multilayer composite was produced by hot-rolling of anodized and non-anodized aluminum foils alternately sandwiched.In addition,the same process was applied for bonding of non-anodized foils.In both cases,obtained multilayer composites were compact and sound.In order to study composites microstructural evolution and mechanical properties,optical and scanning electron microscopy(SEM),energy dispersive spectrometry(EDS),X-ray diffraction(XRD)analysis,hardness,tensile and three-point flexural tests were performed.Microstructural characterization confirmed that the rod-like particles distributed in parallel rows in the composite aluminum matrix with anodized foils correspond to Al2O3.Maximum and minimum peaks of oxygen and aluminum,respectively,suggest that after the final hot-rolling of composite with non-anodized foils,a small amount of coarser particles were formed at boundaries between foils.Hardness,strength,modulus of elasticity and flexural strength of both multilayer composites were much higher than those of pure aluminum,whereas ductility was significantly less.The composite with anodized foils exhibited the highest strength and modulus of elasticity,but lower ductility compared to composite processed from non-anodized foils.Fracture failure corresponded to the change of ductility.
基金Project(2005CB623703) supported by the National Basic Research Program of China
文摘The CaO doped 10NiO-NiFe2O4 composite ceramics were prepared by the cold isostatic pressing-sintering process, and the effects of CaO content on the phase composition, mechanical property and thermal shock resistance of 10NiO-NiFe2O4 composite ceramics were studied. The results show that the samples mainly consist of NiO and NiFe2O4 when content of CaO is less than 4%(mass fraction), bending strength increases obviously by CaO doping. Bending strength of the samples doped with 2% CaO is above 185 MPa, but that of the samples without CaO is only 60 MPa. Fracture toughness is improved obviously by CaO doping, the samples doped with 2% CaO have the maximum fracture toughness of 2.12 MPa ·m1/2 , which is about two times of that of the undoped ceramics. CaO doping is bad to thermal shock resistance of 10NiO-NiFe2O4 composite ceramics.
